Hi, Heiko. On 09/01/2015 03:24 AM, Heiko Stuebner wrote: > From: Alexandru M Stan <amstan@xxxxxxxxxxxx> > > Add ciu_drv, ciu_sample clocks and default-sample-phase. This will later > be used by tuning code. As i know, ciu_drv and ciu_sample clocks are generated with "ciu" clock. But in these patch-set, ciu_drv and ciu_sample are controlled by clock framework. It's a little strange. Are there ciu_drv and ciu_sample clock on Rockchip? Best Regards, Jaehoon Chung > > We do not touch ciu_drive (and by extension define default-drive-phase). > Drive phase is mostly used to define minimum hold times, while one could > write some code to determine what phase meets the minimum hold time > (ex 10 degrees) this will not work with the current clock phase framework > (which floors angles, so we'll get 0 deg, and there's no way to know what > resolution the floors happen at). We assume that the default drive angles > set by the hardware are good enough. > > Signed-off-by: Alexandru M Stan <amstan@xxxxxxxxxxxx> > Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx> > --- > Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt | 14 ++++++++++---- > 1 file changed, 10 insertions(+), 4 deletions(-) > > diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt > index 346c609..5edadc2 100644 > --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt > +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt > @@ -42,11 +42,13 @@ Optional properties: > * clocks: from common clock binding: handle to biu and ciu clocks for the > bus interface unit clock and the card interface unit clock. > > -* clock-names: from common clock binding: Shall be "biu" and "ciu". > - If the biu clock is missing we'll simply skip enabling it. If the > - ciu clock is missing we'll just assume that the clock is running at > +* clock-names: from common clock binding: Shall be "biu", "ciu", "ciu_drv" and > + "ciu_sample". If the biu clock is missing we'll simply skip enabling it. > + If the ciu clock is missing we'll just assume that the clock is running at > clock-frequency. It is an error to omit both the ciu clock and the > - clock-frequency. > + clock-frequency. "ciu_drv" and "ciu_sample" are used to control the clock > + phases, "ciu_sample" is required for tuning high speed modes (if no other > + custom tuning method is defined). > > * clock-frequency: should be the frequency (in Hz) of the ciu clock. If this > is specified and the ciu clock is specified then we'll try to set the ciu > @@ -75,6 +77,10 @@ Optional properties: > * vmmc-supply: The phandle to the regulator to use for vmmc. If this is > specified we'll defer probe until we can find this regulator. > > +* default-sample-phase: The default phase to set ciu_sample at probing, low > + speeds or in case where all phases work at tuning time. If not specified > + 0 deg will be used. > + > Aliases: > > - All the MSHC controller nodes should be represented in the aliases node using > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
