在 2015/8/15 6:13, Heiko Stübner 写道:
Hi Shawn,
Am Freitag, 14. August 2015, 16:34:35 schrieb Shawn Lin:
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK312x
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx>
judging by your "from", I guess you're running this on some older Rockchip soc
without the idma? Because I tried testing this on a Radxa Rock, but only got
failures, from the start (failed to read card status register). In PIO mode
everything works again.
I guess I overlooked just some tiny detail, but to me the dma channel ids seem
correct after all. Maybe you have any hints what I'm doing wrong?
Thanks, HeiKo.
yes, I'm running a quite older low-end Rockchip soc w/o idma.
Hmm... from your failure to read CSR, I think generic DMA of Radxa Rock
was not runing properly. Your dma channel ids is correct, but it
certainly work on my platform。 I will try to find a Radxa Rock to
re-test my patch ASAP.
diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rk3xxx.dtsi
index 4497d28..92d7156 100644
--- a/arch/arm/boot/dts/rk3xxx.dtsi
+++ b/arch/arm/boot/dts/rk3xxx.dtsi
@@ -217,6 +217,8 @@
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>;
clock-names = "biu", "ciu";
+ dmas = <&dmac2 1>;
+ dma-names = "rx-tx";
fifo-depth = <256>;
status = "disabled";
};
@@ -227,6 +229,8 @@
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>;
clock-names = "biu", "ciu";
+ dmas = <&dmac2 3>;
+ dma-names = "rx-tx";
fifo-depth = <256>;
status = "disabled";
};
@@ -237,6 +241,8 @@
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>;
clock-names = "biu", "ciu";
+ dmas = <&dmac2 4>;
+ dma-names = "rx-tx";
fifo-depth = <256>;
status = "disabled";
};
[...]
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index fcbf552..e01ead3 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -2517,8 +2642,23 @@ static void dw_mci_cleanup_slot(struct dw_mci_slot
*slot, unsigned int id) static void dw_mci_init_dma(struct dw_mci *host)
{
int addr_config;
+ int trans_mode;
+ struct device *dev = host->dev;
+ struct device_node *np = dev->of_node;
+
+ /* Check tansfer mode */
+ trans_mode = SDMMC_GET_TRANS_MODE(mci_readl(host, HCON));
+ if (trans_mode == 0) {
+ trans_mode = TRANS_MODE_IDMAC;
+ } else if (trans_mode == 1 || trans_mode == 2) {
+ trans_mode = TRANS_MODE_EDMAC;
+ } else {
+ trans_mode = TRANS_MODE_PIO;
+ goto no_dma;
+ }
+
/* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */
- addr_config = (mci_readl(host, HCON) >> 27) & 0x01;
+ addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON));
if (addr_config == 1) {
/* host supports IDMAC in 64-bit address mode */
I guess the idmac address size checking block
/* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */
addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON));
if (addr_config == 1) {
/* host supports IDMAC in 64-bit address mode */
host->dma_64bit_address = 1;
dev_info(host->dev, "IDMAC supports 64-bit address mode.\n");
if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
dma_set_coherent_mask(host->dev, DMA_BIT_MASK(64));
} else {
/* host supports IDMAC in 32-bit address mode */
host->dma_64bit_address = 0;
dev_info(host->dev, "IDMAC supports 32-bit address mode.\n");
}
could either live inside the trans_mode == 0 conditional above or get its own
if (trans_mode == 0) conditional. Either way I guess it should not talk about
idmac when either pio or extdmac are used.
Thanks
Heiko
--
Shawn Lin
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
