On 2015.02.09 12:51, Ulf Hansson wrote:
On 5 February 2015 at 12:13, Addy Ke <addy.ke@xxxxxxxxxxxxxx> wrote:
Because of some uncertain factors, such as worse card or worse hardware,
DAT[3:0](the data lines) may be pulled down by card, and mmc controller
will be in busy state. This should not happend when mmc controller
send command to update card clocks. If this happends, mci_send_cmd will
be failed and we will get 'Timeout sending command', and then system will
be blocked. To avoid this, we need reset mmc controller.
Signed-off-by: Addy Ke <addy.ke@xxxxxxxxxxxxxx>
Hi Addy,
Should I consider $subject patch as a better option to the one below?
No:
This patch fix the bug, which can be found by script:
cd /sys/bus/platform/drivers/dwmmc_rockchip
for i in $(seq 1 10000); do
echo "========================" $i
echo ff0c0000.dwmmc > unbind
sleep .5
echo ff0c0000.dwmmc > bind
sleep 2
done
[PATCH] mmc: dw_mmc: rockchip: Add DW_MCI_QUIRK_RETRY_DELAY
This patch is for tuning issue: we should delay until card go to idle
state, when the previous command return error.
https://lkml.org/lkml/2015/1/13/562
Kind regards
Uffe
---
drivers/mmc/host/dw_mmc.c | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 4d2e3c2..b1d6dfb 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -100,6 +100,7 @@ struct idmac_desc {
};
#endif /* CONFIG_MMC_DW_IDMAC */
+static int dw_mci_card_busy(struct mmc_host *mmc);
static bool dw_mci_reset(struct dw_mci *host);
static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset);
@@ -888,6 +889,26 @@ static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
cmd, arg, cmd_status);
}
+static void dw_mci_wait_busy(struct dw_mci_slot *slot)
+{
+ struct dw_mci *host = slot->host;
+ unsigned long timeout = jiffies + msecs_to_jiffies(500);
+
+ while (time_before(jiffies, timeout)) {
+ if (!dw_mci_card_busy(slot->mmc))
+ return;
+ }
+ dev_err(host->dev, "Data busy (status %#x)\n",
+ mci_readl(slot->host, STATUS));
+
+ /*
+ * Data busy, this should not happend when mmc controller send command
+ * to update card clocks in non-volt-switch state. If it happends, we
+ * should reset controller to avoid getting "Timeout sending command".
+ */
+ dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS);
+}
+
static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
{
struct dw_mci *host = slot->host;
@@ -899,6 +920,8 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
/* We must continue to set bit 28 in CMD until the change is complete */
if (host->state == STATE_WAITING_CMD11_DONE)
sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH;
+ else
+ dw_mci_wait_busy(slot);
if (!clock) {
mci_writel(host, CLKENA, 0);
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
