[PATCH 4/4] mmc: core: hold SD Clock before CMD11 during Signal

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Voltage Switch Procedure

This patch is to fix an issue found on mb86s7x platforms.

[symptom]
There are some UHS-1 SD memory cards sometimes cannot be detected correctly,
e.g., Transcend 600x SDXC 64GB UHS-1 memory card.
During Signal Voltage Switch Procedure, failure to switch is indicated
by the card holding DAT[3:0] low.

[analysis]
According to SD Host Controller Simplified Specification Version 3.00
chapter 3.6.1, the Signal Voltage Switch Procedure should be:
(1) Check S18A; (2) Issue CMD11; (3) Check CMD 11 response;
(4) Stop providing SD clock; (5) Check DAT[3:0] should be 0000b;
(6) Set 1.8V Signal Enable; (7) Wait 5ms; (8) Check 1.8V Signal Enable;
(9) Provide SD Clock; (10) Wait 1ms; (11) Check DAT[3:0] should be 1111b;
(12) error handling

With CONFIG_MMC_CLKGATE=y, sometimes there is one more gating/un-gating
SD clock between (2) and (3). In this case, some UHS-1 SD cards will hold
DAT[3:0] 0000b at (11) and thus fails Signal Voltage Switch Procedure.

[solution]
By mmc_host_clk_hold() before CMD11, the additional gating/un-gating
SD clock between (2) and (3) can be prevented and thus no failure at (11).
It has been verified with many UHS-1 SD cards on mb86s7x platforms and
works correctly.

Signed-off-by: Vincent Yang <Vincent.Yang@xxxxxxxxxxxxxx>
---
 drivers/mmc/core/core.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index f26a5f1..8b9e2cfd 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -1420,18 +1420,20 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr)
 		pr_warn("%s: cannot verify signal voltage switch\n",
 			mmc_hostname(host));
 
+	mmc_host_clk_hold(host);
+
 	cmd.opcode = SD_SWITCH_VOLTAGE;
 	cmd.arg = 0;
 	cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
 
 	err = mmc_wait_for_cmd(host, &cmd, 0);
 	if (err)
-		return err;
-
-	if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
-		return -EIO;
+		goto err_command;
 
-	mmc_host_clk_hold(host);
+	if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) {
+		err = -EIO;
+		goto err_command;
+	}
 	/*
 	 * The card should drive cmd and dat[0:3] low immediately
 	 * after the response of cmd11, but wait 1 ms to be sure
@@ -1480,6 +1482,7 @@ power_cycle:
 		mmc_power_cycle(host, ocr);
 	}
 
+err_command:
 	mmc_host_clk_release(host);
 
 	return err;
-- 
1.9.0

--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux