Bartlomiej, On Thu, Oct 2, 2014 at 10:24 AM, Bartlomiej Zolnierkiewicz <b.zolnierkie@xxxxxxxxxxx> wrote: > > Hi, > > On Thursday, October 02, 2014 09:45:41 AM Doug Anderson wrote: >> Bartiomiej >> >> On Thu, Oct 2, 2014 at 9:39 AM, Bartlomiej Zolnierkiewicz >> <b.zolnierkie@xxxxxxxxxxx> wrote: >> > On Thursday, October 02, 2014 09:19:08 AM Doug Anderson wrote: >> >> Bartiomiej, >> >> >> >> On Thu, Oct 2, 2014 at 9:10 AM, Bartlomiej Zolnierkiewicz >> >> <b.zolnierkie@xxxxxxxxxxx> wrote: >> >> > Regulators for MMC2 (SD card) are PVDD_TFLASH_2V8 (LDO19) for vmmc >> >> > and PVDD_APIO_MMCOFF_2V8 (LDO13) for vqmmc. Currently the device >> >> > tree entry for MMC2 uses PVDD_PRE_1V8 (LDO10) for vmmc and vqmmc is >> >> > not specified. Fix it. >> >> > >> >> > Without this patch: >> >> > - "mmc: dw_mmc: use mmc_regulator_get_supply to handle regulators" >> >> > patch causes a SD card detection to fail >> >> > - "mmc: dw_mmc: Support voltage changes" patch causes a boot hang >> >> > >> >> > This patch fixes both above problems. >> >> > >> >> > Suggested-by: Doug Anderson <dianders@xxxxxxxxxx> >> >> > Cc: Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxxxx> >> >> > Cc: Ulf Hansson <ulf.hansson@xxxxxxxxxx> >> >> > Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@xxxxxxxxxxx> >> >> > Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx> >> >> > --- >> >> > arch/arm/boot/dts/exynos5420-arndale-octa.dts | 3 ++- >> >> > 1 file changed, 2 insertions(+), 1 deletion(-) >> >> > >> >> > Index: b/arch/arm/boot/dts/exynos5420-arndale-octa.dts >> >> > =================================================================== >> >> > --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts 2014-10-02 15:44:53.014826886 +0200 >> >> > +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts 2014-10-02 17:35:24.110600398 +0200 >> >> > @@ -74,7 +74,8 @@ >> >> > samsung,dw-mshc-ddr-timing = <1 2>; >> >> > pinctrl-names = "default"; >> >> > pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >> >> > - vmmc-supply = <&ldo10_reg>; >> >> > + vmmc-supply = <&ldo19_reg>; >> >> > + vqmmc-supply = <&ldo13_reg>; >> >> >> >> This looks right to me. ...but I notice that ldo13 and ldo19 are not >> >> "always-on" in the DTS. Are you sure card detect works for you if you >> >> eject your card and try to put it back in? >> >> >> >> ...eventually the "always-on" won't be needed, but for now I think it is... >> > >> > Card detection works fine without "always-on". >> >> That's weird. >> >> 1. In the schematics I see XMMC2CDN has an external pullup to PVDD_TFLASH_2V8. >> >> 2. The internal pullup should (I think) be to VDDQ_MMC2 which is >> PVDD_APIO_MMCOFF_2V8. >> >> 3. In (51da224 mmc: dw_mmc: use mmc_regulator_get_supply to handle >> regulators) we should be turning off both regulators in >> "MMC_POWER_OFF". >> >> 4. If I understand correctly MMC_POWER_OFF is called when the card is >> ejected, which means that both regulators should be off when the card >> is ejected. >> >> 5. I don't think card detect can work if neither regulator is powered. >> >> >> One of the above points must be wrong. Any idea which one? Can you >> check to see if MMC_POWER_OFF is called for you when the card is >> ejected? Can you check to see if these regulators are off? > > MMC_POWER_OFF is called on card removal and both regulators get disabled > (I have verified that they are really off with regulator_is_enabled() which > returns 1 before and 0 after disabling regulator). It seems that 5. is > wrong? This really doesn't make a lot of sense to me, so I'm still kinda confused. If you want to call it good then that's your (and Ulf's) decision, but it's the kind of thing that would keep me up at night. How can this pin be high if all the regulators pulling it up are off? Is there a current leak somewhere and that's why it's working? How this is supposed to work (as I understand it): 1. When no card is inserted then this pin is supposed to be pulled up to VDDQ_MMC2. That could be either an internal or an external pullup. It should be pulled up to VDDQ_MMC2 (as opposed to any other voltage) since the exynos manual documents that this pin lives in the VDDQ_MMC2 io domain. Note that it could be pulled up externally to a different supply than the one going to VDDQ_MMC2, but for correctness it should be the same voltage. 2. When a card is inserted, the pin will be grounded (AKA this is an open drain pin). With your patch, can you probe the pin and see if card detect is high when all the regulators are off? Any idea how it gets high? If you turn off the internal pullup is it still high? -Doug -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
