Re: [PATCH] mmc: Add delay between CMD6 and CMD13 for Sandisk eMMC cards

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



2014-09-15 12:53 GMT+02:00 Jean-Michel Hautbois
<jean-michel.hautbois@xxxxxxxxxxx>:
> 2014-09-15 12:44 GMT+02:00 Jaehoon Chung <jh80.chung@xxxxxxxxxxx>:
>> On 09/15/2014 07:08 PM, Jean-Michel Hautbois wrote:
>>> Hi Jaehoon,
>>>
>>>> On 09/09/2014 09:26 PM, Jean-Michel Hautbois wrote:
>>>>> Tested on a i.MX6 board, with Sandisk SDIN5D1-2G.
>>>>> Without this patch, I/O errors occur.
>>>>> This eMMC seems to have a different Manufacturer ID as it reads 0x45
>>>>> and not 0x2 as specified in datasheet.
>>>>
>>>> I think this patch don't merge into mainline.
>>>> This is not solution for problem.
>>>> you mentioned the below comment, this is workaround.
>>>
>>> Yes
>>>
>>>>>
>>>>> Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx>
>>>>> ---
>>>>>  drivers/mmc/core/mmc_ops.c | 9 +++++++++
>>>>>  1 file changed, 9 insertions(+)
>>>>>
>>>>> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
>>>>> index f51b5ba..91babaa 100644
>>>>> --- a/drivers/mmc/core/mmc_ops.c
>>>>> +++ b/drivers/mmc/core/mmc_ops.c
>>>>> @@ -458,6 +458,15 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
>>>>>       if (!use_busy_signal)
>>>>>               return 0;
>>>>>
>>>>> +     /* WORKAROUND: for Sandisk eMMC cards, it might need certain delay
>>>>> +      * before sending CMD13 after CMD6
>>>>> +      * On SDIN5D1-2G MANFID is 0x45 and not 0x2 as specified in datasheet
>>>>> +      */
>>>>> +     if (card->cid.manfid == CID_MANFID_SANDISK ||
>>>>> +             card->cid.manfid == 0x45) {
>>>>> +             msleep(1);
>>>>> +     }
>>>>
>>>> If it's a general problem of Sandisk SDIN5D1-2G,
>>>> I think you need to verify this problem. And can you use the MMC_FIXUP() and QUIRK?
>>>
>>> Well, this is difficult to verify, I know that on all my SDIN5D1-2G I
>>> have this MANFID different from what is defined by CID_MANFID_SANDISK.
>>> How should I use MMC_FIXUP ? Like this ?
>>
>> I think you need to explain why delay is need.
>> i didn't have same card, but it might be your host controller or other problem.
>
> Well, I don't know why it is needed, this is undocumented, nothing in
> datasheet explains anything about this.

It seems to be uSDHC / DDR mode related. I don't even know if this is
limited to Sandisk !
And I don't have another board with another manufacturer eMMC to test.
Maybe some guys from Freescale could help with this ?

Thanks,
JM
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux