Re: [PATCHv6 1/5] mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jaehoon,

Am 25.07.2014 03:11, schrieb Jaehoon Chung:
> Almost Soc is used the slot per a host.

Something's very wrong with this sentence. What are you trying to say?
Almost all SoCs use one slot only per host controller device?

> Don't use the slot-node and deprecated the "supports-highsped" property.

s/deprecated/deprecate/ ?
s/highsped/highspeed/

> Instead, use the cap-mmc/sd-highspeed.
> 
> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
> Reviewed-by: Tushar Behera <trblinux@xxxxxxxxx>
> Reviewed-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> Tested-by: Sachin Kamat <sachin.kamat@xxxxxxxxxxx>
> Acked-by: Seungwon Jeon <tgih.jun@xxxxxxxxxxx>
> ---
>  .../devicetree/bindings/mmc/exynos-dw-mshc.txt     |   17 +++++------------
>  .../devicetree/bindings/mmc/k3-dw-mshc.txt         |   12 +++++-------
>  .../devicetree/bindings/mmc/synopsys-dw-mshc.txt   |   12 +++++-------
>  3 files changed, 15 insertions(+), 26 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> index 532b1d4..9308325 100644
> --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> @@ -46,13 +46,14 @@ Required Properties:
>        - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
>          phase shift clocks should be 0.
>  
> -Required properties for a slot:
> +Required properties for a slot (Deprecated - Recommend to use one slot per a host):

"per host"

>  
>  * gpios: specifies a list of gpios used for command, clock and data bus. The
>    first gpio is the command line and the second gpio is the clock line. The
>    rest of the gpios (depending on the bus-width property) are the data lines in
>    no particular order. The format of the gpio specifier depends on the gpio
>    controller.
> + (Deprecated - Refer to Documentaion/devicetree/binding/pinctrl/samsung-pinctrl.txt)

"Documentation/"

Nit: Is the indentation intentional? (parenthesis not aligned with text)

>  
>  Example:
>  
> @@ -69,21 +70,13 @@ Example:
>  
>  	dwmmc0@12200000 {
>  		num-slots = <1>;
> -		supports-highspeed;
> +		cap-mmc-highspeed;
> +		cap-sd-highspeed;
>  		broken-cd;
>  		fifo-depth = <0x80>;
>  		card-detect-delay = <200>;
>  		samsung,dw-mshc-ciu-div = <3>;
>  		samsung,dw-mshc-sdr-timing = <2 3>;
>  		samsung,dw-mshc-ddr-timing = <1 2>;
> -
> -		slot@0 {
> -			reg = <0>;
> -			bus-width = <8>;
> -			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
> -				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
> -				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
> -				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
> -				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
> -		};
> +		bus-width = <8>;
>  	};
> diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
> index e5bc49f..3b35449 100644
> --- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
> @@ -34,13 +34,11 @@ Example:
>  		num-slots = <1>;
>  		vmmc-supply = <&ldo12>;
>  		fifo-depth = <0x100>;
> -		supports-highspeed;
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&sd_pmx_pins &sd_cfg_func1 &sd_cfg_func2>;
> -		slot@0 {
> -			reg = <0>;
> -			bus-width = <4>;
> -			disable-wp;
> -			cd-gpios = <&gpio10 3 0>;
> -		};
> +		bus-width = <4>;
> +		disable-wp;
> +		cd-gpios = <&gpio10 3 0>;
> +		cap-mmc-highspeed;
> +		cap-sd-highspeed;
>  	};
> diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> index 2d4a725..346c609 100644
> --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> @@ -67,7 +67,8 @@ Optional properties:
>  * card-detect-delay: Delay in milli-seconds before detecting card after card
>    insert event. The default value is 0.
>  
> -* supports-highspeed: Enables support for high speed cards (up to 50MHz)
> +* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz)
> +			   (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead)
>  
>  * broken-cd: as documented in mmc core bindings.
>  
> @@ -98,14 +99,11 @@ board specific portions as listed below.
>  		clock-frequency = <400000000>;
>  		clock-freq-min-max = <400000 200000000>;
>  		num-slots = <1>;
> -		supports-highspeed;
>  		broken-cd;
>  		fifo-depth = <0x80>;
>  		card-detect-delay = <200>;
>  		vmmc-supply = <&buck8>;
> -
> -		slot@0 {
> -			reg = <0>;
> -			bus-width = <8>;
> -		};
> +		bus-width = <8>;
> +		cap-mmc-highspeed;
> +		cap-sd-highspeed;
>  	};

Regards,
Andreas

-- 
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux