On 05/26/14 09:48, Hans de Goede wrote:
It has taken me a long long time to get the OOB interrupt working on the
AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
end I found these magic register pokes in the cubietruck kernel tree:
https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a
I'm not entirely sure if this specific to the AP6210 module, or if this
should be done for all BCM43362 sdio devices.
Let keep it as this for now. I added some remarks below.
Regards,
Arend
Signed-off-by: Hans de Goede<hdegoede@xxxxxxxxxx>
---
drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
index 0fc707c..2369a0f 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
@@ -39,7 +39,9 @@
#include<brcm_hw_ids.h>
#include<brcmu_utils.h>
#include<brcmu_wifi.h>
+#include<chipcommon.h>
#include<soc.h>
+#include "chip.h"
#include "dhd_bus.h"
#include "dhd_dbg.h"
#include "sdio_host.h"
@@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
{
int ret = 0;
u8 data;
+ u32 addr, gpiocontrol;
unsigned long flags;
if ((sdiodev->pdata)&& (sdiodev->pdata->oob_irq_supported)) {
@@ -148,6 +151,21 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
sdio_claim_host(sdiodev->func[1]);
+ if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) {
+ /* assign GPIO to SDIO core */
+ addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol);
+ gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr,&ret);
+ gpiocontrol |= 0x2;
+ brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol,&ret);
+
+ /* SPROM_ADDR_HIGH ? perhaps the defines name is off */
These names are all off. These should be:
SBSDIO_SPROM_ADDR_HIGH = SBSDIO_GPIO_SELECT
SBSDIO_CHIP_CTRL_DATA = SBSDIO_GPIO_OUT
SBSDIO_CHIP_CTRL_EN = SBSDIO_GPIO_EN
+ brcmf_sdiod_regwb(sdiodev, SBSDIO_SPROM_ADDR_HIGH, 0xf,
+ &ret);
+ brcmf_sdiod_regwb(sdiodev, SBSDIO_CHIP_CTRL_DATA, 0,
+ &ret);
+ brcmf_sdiod_regwb(sdiodev, SBSDIO_CHIP_CTRL_EN, 0x2,
+ &ret);
+ }
+
/* must configure SDIO_CCCR_IENx to enable irq */
data = brcmf_sdiod_regrb(sdiodev, SDIO_CCCR_IENx,&ret);
data |= 1<< SDIO_FUNC_1 | 1<< SDIO_FUNC_2 | 1;
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
