On 15.02.2014 21:52, Russell King - ARM Linux wrote:
On Sat, Feb 15, 2014 at 05:21:11PM +0100, Arnd Bergmann wrote:
On Saturday 15 February 2014 14:22:30 Tomasz Figa wrote:
On 15.02.2014 14:09, Arnd Bergmann wrote:
For spi-mode SDIO devices I'm assuming it's similar, except that
you'd describe the actual SDIO device in the board info rather than
create a fake SDIO controller. Still not discoverable unless I'm
missing your point.
I'm not sure if we should assume that SPI = MMC over SPI. I believe
there might be a custom protocol involved as well.
In case of SD/MMC, you essentially have three separate command sets:
SPI, MMC and SD, and each of them has multiple versions. MMC and SD
compatible devices generally also support the SPI command set (IIRC
it is required,
SPI support is mandatory for SDIO as well.
SDIO has CIS (remember card information structures... like PCMCIA)
which identifies the various different logical functions of the device,
giving class information, vendor information etc.
So... certainly the type of the attached device is discoverable even
on SPI.
It certainly is, assuming that you properly configure the
non-discoverable part.
If a device supports both SDIO and SPI, I think a straightforward
implementation would be to use the exact same command set, but
you are right that this isn't the only possibility, and the SD/MMC
shows how they can be slightly different already.
Given that the SPI mode is mandatory for SDIO cards, why would you
also implement another SPI mode with different commands?
Well, isn't this embedded world we're living in a constant race between
software and hardware engineers, where the former invent more and more
generic solutions to cover wider ranges of hardware with nice
abstractions, while the latter invent more quirky hardware designs to
destroy the effort of the former? Cute embedded nonsense hacks and so...
Stepping aside from SPI, I already gave an example of a WLAN chip that
supports multiple control busses [1]. In addition to the commonly used
SDIO, it supports USB and HSIC as well:
[1] http://www.marvell.com/wireless/assets/marvell_avastar_88w8797.pdf
Moreover, some of Samsung boards use HSIC to communicate with modem
chips, which have exactly the same problem as we're trying to solve here
- they need to be powered on to be discovered.
Thanks, this definitely makes a good example. I see that it also
supports SPI mode for SDIO as mentioned in your link.
Well, USB is another discoverable bus. As HSIC is a derivative of USB,
I'd be surprised if it weren't discoverable there too.
So, out of everything identified so far, we have no undiscoverable buses.
Agreed. Putting the same chip on USB or HSIC has the exact same
requirements, since we also have a discoverable bus, but actually
finding the device likely involves some power-on sequencing before
the bus controller can find it.
That's partly the nature of integrating something onto a board where you
want maximal power savings. It's basically that dreaded word which
software people seem to hate: "embedded".
This isn't something we can ignore, though.
* Arnd's proposal (change bus code to probe nonstandard devices
from DT if we can't easily detect them):
+ Matches what we already do for PCI (at least on powerpc)
and AMBA/Primecell devices: If a device can't be probed
using the standard method, we treat it as nondiscoverable
and describe it using DT.
+ Devices can have arbitrary complex requirements without
impacting the core, since all code is contained in the
driver for the nonstandard device.
+ Properties that are required for probing and runtime
configuration only have to be set once (e.g. you may
need clk_get() for probing and clk_set_rate() for
runtime-pm).
+ Devices that have alternative bus interfaces like 88w8797
can implement the power-on code in a central place per
driver, and can reuse the code they have for nondiscoverable
buses on the buses that are normally discoverable but
broken here.
- Still need to modify each subsystem to have alternate
ways of probing, and match up devices later.
- Has to be implemented in each driver that needs it, making
it harder to share code for drivers with the same need
(e.g. every device that just needs an external reset
trigger).
- requires different DT if the chip is changed, which causes problems
for users to identify which out of zillions of DT files they should
use for their exact platform.
That's how things work in embedded world, unfortunately. As Arnd stated
in one of his previous replies, different chips use to have different
power-up sequences and set of data the driver needs to know.
If you change your hardware in an incompatible way and such change can't
be detected automatically (i.e. the chip is non-discoverable) then I
don't know how you could let the OS know about this change in any other
way than providing it with the information it needs.
- have to work out how to match up the fake device with a probed device
when it becomes available: existing SDIO drivers all assume that the
card has been through a fairly complex initialisation sequence already.
- multi-function SDIO is much harder to deal with since you have mutliple
drivers involved, and the SDIO device as a whole needs initialisation
before anyone can drive it.
- adds complexity to the SDIO drivers; they would have to know whether
they're embedded or on a plug-in card.
The three points above could be eliminated by adopting the solution I
proposed [1]. Moreover it could be analogically implemented for other
bus types and use almost identical DT bindings.
[1] http://thread.gmane.org/gmane.linux.kernel.mmc/24728/focus=24864
Best regards,
Tomasz
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
