Hi,
Apologies for the delayed reply.
On 12/09/2013 07:00 PM, Courtney Cavin wrote:
On Wed, Nov 06, 2013 at 04:56:45PM +0100, Georgi Djakov wrote:
This platform driver adds the initial support of Secure
Digital Host Controller Interface compliant controller
found in Qualcomm MSM chipsets.
Signed-off-by: Georgi Djakov <gdjakov@xxxxxxxxxx>
[...]
+static int sdhci_msm_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_msm_host *msm_host;
+ struct resource *core_memres = NULL;
+ int ret, dead;
+ u16 host_version;
+ u32 irq_status, irq_ctl;
+
+ if (!pdev->dev.of_node) {
+ dev_err(&pdev->dev, "No device tree data\n");
+ return -ENOENT;
+ }
+
+ msm_host = devm_kzalloc(&pdev->dev, sizeof(*msm_host), GFP_KERNEL);
+ if (!msm_host)
+ return -ENOMEM;
+
+ msm_host->sdhci_msm_pdata.ops = &sdhci_msm_ops;
+ host = sdhci_pltfm_init(pdev, &msm_host->sdhci_msm_pdata, 0);
+ if (IS_ERR(host)) {
+ dev_err(mmc_dev(host->mmc), "sdhci_pltfm_init error\n");
+ return PTR_ERR(host);
+ }
+
+ pltfm_host = sdhci_priv(host);
+ pltfm_host->priv = msm_host;
+ msm_host->mmc = host->mmc;
+ msm_host->pdev = pdev;
+
+ ret = mmc_of_parse(host->mmc);
Can we please add a call to sdhci_get_of_property(pdev) somewhere around
here too?
Thanks, I have added it to v8.
+ if (ret) {
+ dev_err(&pdev->dev, "failed parsing mmc device tree\n");
+ goto pltfm_free;
+ }
+
+ ret = sdhci_msm_populate_pdata(&pdev->dev, &msm_host->pdata);
+ if (ret) {
+ dev_err(&pdev->dev, "DT parsing error\n");
+ goto pltfm_free;
+ }
+
+ /* Setup SDCC bus voter clock. */
+ msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
+ if (!IS_ERR(msm_host->bus_clk)) {
+ /* Vote for max. clk rate for max. performance */
+ ret = clk_set_rate(msm_host->bus_clk, INT_MAX);
+ if (ret)
+ goto pltfm_free;
+ ret = clk_prepare_enable(msm_host->bus_clk);
+ if (ret)
+ goto pltfm_free;
+ }
+
+ /* Setup main peripheral bus clock */
+ msm_host->pclk = devm_clk_get(&pdev->dev, "iface");
+ if (!IS_ERR(msm_host->pclk)) {
+ ret = clk_prepare_enable(msm_host->pclk);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Main peripheral clock setup fail (%d)\n",
+ ret);
+ goto bus_clk_disable;
+ }
+ }
+
+ /* Setup SDC MMC clock */
+ msm_host->clk = devm_clk_get(&pdev->dev, "core");
+ if (IS_ERR(msm_host->clk)) {
+ ret = PTR_ERR(msm_host->clk);
+ dev_err(&pdev->dev, "SDC MMC clock setup fail (%d)\n", ret);
+ goto pclk_disable;
+ }
+
+ ret = clk_prepare_enable(msm_host->clk);
+ if (ret)
+ goto pclk_disable;
+
+ /* Setup regulators */
+ ret = sdhci_msm_vreg_init(&pdev->dev, &msm_host->pdata);
+ if (ret) {
+ if (ret != -EPROBE_DEFER)
+ dev_err(&pdev->dev, "Regulator setup fail (%d)\n", ret);
+ goto clk_disable;
+ }
+
+ core_memres = platform_get_resource_byname(pdev,
+ IORESOURCE_MEM, "core_mem");
+ msm_host->core_mem = devm_ioremap_resource(&pdev->dev, core_memres);
+
+ if (IS_ERR(msm_host->core_mem)) {
+ dev_err(&pdev->dev, "Failed to remap registers\n");
+ ret = PTR_ERR(msm_host->core_mem);
+ goto vreg_disable;
+ }
+
+ /* Reset the core and Enable SDHC mode */
+ writel_relaxed(readl_relaxed(msm_host->core_mem + CORE_POWER) |
+ CORE_SW_RST, msm_host->core_mem + CORE_POWER);
+
+ /* SW reset can take upto 10HCLK + 15MCLK cycles. (min 40us) */
+ usleep_range(1000, 5000);
+ if (readl(msm_host->core_mem + CORE_POWER) & CORE_SW_RST) {
+ dev_err(&pdev->dev, "Stuck in reset\n");
+ ret = -ETIMEDOUT;
+ goto vreg_disable;
+ }
+
+ /* Set HC_MODE_EN bit in HC_MODE register */
+ writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE));
+
+ /*
+ * CORE_SW_RST above may trigger power irq if previous status of PWRCTL
+ * was either BUS_ON or IO_HIGH_V. So before we enable the power irq
+ * interrupt in GIC (by registering the interrupt handler), we need to
+ * ensure that any pending power irq interrupt status is acknowledged
+ * otherwise power irq interrupt handler would be fired prematurely.
+ */
+ irq_status = readl_relaxed(msm_host->core_mem + CORE_PWRCTL_STATUS);
+ writel_relaxed(irq_status, (msm_host->core_mem + CORE_PWRCTL_CLEAR));
+ irq_ctl = readl_relaxed(msm_host->core_mem + CORE_PWRCTL_CTL);
+ if (irq_status & (CORE_PWRCTL_BUS_ON | CORE_PWRCTL_BUS_OFF))
+ irq_ctl |= CORE_PWRCTL_BUS_SUCCESS;
+ if (irq_status & (CORE_PWRCTL_IO_HIGH | CORE_PWRCTL_IO_LOW))
+ irq_ctl |= CORE_PWRCTL_IO_SUCCESS;
+ writel_relaxed(irq_ctl, (msm_host->core_mem + CORE_PWRCTL_CTL));
+ /*
+ * Ensure that above writes are propogated before interrupt enablement
+ * in GIC.
+ */
+ mb();
+
+ /*
+ * Following are the deviations from SDHC spec v3.0 -
+ * 1. Card detection is handled using separate GPIO.
+ * 2. Bus power control is handled by interacting with PMIC.
+ */
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+ host->quirks |= SDHCI_QUIRK_SINGLE_POWER_WRITE;
I couldn't get v6 running without the 5 quirks you submitted in [1].
Aren't these also attributes of the controller itself? If so, shouldn't they
be part of this patch series, and included here?
Most of the quirks are for older hardware revisions. On what board/chip
are you trying to run it? I will post v8 shortly. Could you try with it
please?
Thanks,
Georgi
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html