On Mon, December 09, 2013, Dinh Nguyen wrote:
> From: Dinh Nguyen <dinguyen@xxxxxxxxxx>
>
> This patch will enable the SDMMC_CMD_USE_HOLD_REG bit when the slot is
> operating all timing modes, except for SDR50, DDR50, SDR104, and MMC_HS200.
>
> According to the Synopsys databook :"To meet the relatively high Input Hold
> Time requirement for SDR12, SDR25, and other MMC speed modes, you should
> program bit[29]use_hold_Reg of the CMD register to 1'b1;"..."However, for
> the higher speed modes of SDR104, SDR50 and DDR50, you can meet the much
> smaller Input Hold Time requirement of 0.8ns by bypassing the Hold Register
> (Path A in Figure 10-8, programming CMD.use_hold_reg = 1'b0) and then adding
> delay elements on the output path as indicated.
>
> Also, "Never set CMD.use_hold_reg = 1 and cclk_in_drv phase shift to 0 at the
> same time. This would add an extra one-cycle delay on the output path, resulting
> in incorrect behavior."
>
> This patch also checks the IHR(Implement Hold Register) in the HCON register.
>
> This information is taking from the v2.50a of the Synopsys Designware Cores
> Mobile Storage Host Databook.
If cclk_in_drv has non-zero, hold_reg_bit should be 1'b1 for SDR50, DDR50, SDR104, and MMC_HS200 mode.
Can you check it?
And samsung,dw-mshc-sdr(ddr)-timing property is still specific for Exynos.
It will be modified with adding new cell element soon.
Thanks,
Seungwon Jeon
>
> Signed-off-by: Dinh Nguyen <dinguyen@xxxxxxxxxx>
> Acked-by: Heiko Stuebner <heiko@xxxxxxxxx>
> Tested-by: Heiko Stuebner <heiko@xxxxxxxxx>
> ---
> v3: Read the IHR(Implement Hold Register) in the HCON
> v2: Add check for cclk_in_drv phase shift in conjunction with use_hold_reg.
> ---
> drivers/mmc/host/dw_mmc.c | 51 ++++++++++++++++++++++++++++++++++++++++++++
> drivers/mmc/host/dw_mmc.h | 4 ++++
> include/linux/mmc/dw_mmc.h | 3 +++
> 3 files changed, 58 insertions(+)
>
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 4bce0de..480dafe 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -279,6 +279,9 @@ static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
> cmdr |= SDMMC_CMD_DAT_WR;
> }
>
> + if (slot->host->use_hold_reg)
> + cmdr |= SDMMC_CMD_USE_HOLD_REG;
> +
> if (drv_data && drv_data->prepare_command)
> drv_data->prepare_command(slot->host, &cmdr);
>
> @@ -969,6 +972,24 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> mci_writel(slot->host, UHS_REG, regs);
> slot->host->timing = ios->timing;
>
> + /* Per Synopsys spec, use_hold_reg should be set for all modes except for
> + * high-speed SDR50, DDR50, SDR104, and MMC_HS200. However, use_hold_reg
> + * should be cleared if the cclk_in_drv is 0.
> + */
> + switch (slot->host->timing) {
> + case MMC_TIMING_UHS_SDR50:
> + case MMC_TIMING_UHS_SDR104:
> + case MMC_TIMING_UHS_DDR50:
> + case MMC_TIMING_MMC_HS200:
> + slot->host->use_hold_reg = 0;
> + break;
> + default:
> + slot->host->use_hold_reg = 1;
> + }
> +
> + if (slot->host->can_use_hold_reg == 0)
> + slot->host->use_hold_reg = 0;
> +
> /*
> * Use mirror of ios->clock to prevent race with mmc
> * core ios update when finding the minimum.
> @@ -2339,6 +2360,8 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> const struct dw_mci_drv_data *drv_data = host->drv_data;
> int idx, ret;
> u32 clock_frequency;
> + int sdr_timing[2];
> + int ddr_timing[2];
>
> pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
> if (!pdata) {
> @@ -2389,6 +2412,25 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> if (of_find_property(np, "caps2-mmc-hs200-1_2v", NULL))
> pdata->caps2 |= MMC_CAP2_HS200_1_2V_SDR;
>
> + /* Check for the "samsung,dw-mshc-sdr-timing" and the
> + * "samsung,dw-mshc-ddr-timing" bindings as this will tell us if we
> + * can safely set the SDMMC_CMD_USE_HOLD_REG bit. The second paramater
> + * in these 2 bindings is the value of the cclk_in_drv. If cclk_in_drv
> + * is 0, we cannot set the SDMMC_CMD_USE_HOLD_REG bit. The default
> + * behavior will be to set cclk_in_drv, as some platforms do not have
> + * to set the sdr or ddr timing parameters.
> + */
> + sdr_timing[1] = ddr_timing[1] = 1;
> + of_property_read_u32_array(np,
> + "samsung,dw-mshc-sdr-timing", sdr_timing, 2);
> +
> + of_property_read_u32_array(np,
> + "samsung,dw-mshc-ddr-timing", ddr_timing, 2);
> +
> + pdata->cclk_in_drv = 1;
> + if ((sdr_timing[1] == 0) || (ddr_timing[1] == 0))
> + pdata->cclk_in_drv = 0;
> +
> return pdata;
> }
>
> @@ -2495,6 +2537,15 @@ int dw_mci_probe(struct dw_mci *host)
> goto err_regulator;
> }
>
> + /* Check to see if the HOLD REG is implemented. */
> + host->can_use_hold_reg = (mci_readl(host, HCON) & SDMMC_HCON_IHR) >> 22;
> +
> + /* Can only use the HOLD REG is both conditions are true:
> + * Hardware has implemented HOLD_REG and
> + * cclk_in_drv is non-zero.
> + */
> + host->can_use_hold_reg &= host->pdata->cclk_in_drv;
> +
> host->quirks = host->pdata->quirks;
>
> spin_lock_init(&host->lock);
> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
> index 6bf24ab..dfd05c9 100644
> --- a/drivers/mmc/host/dw_mmc.h
> +++ b/drivers/mmc/host/dw_mmc.h
> @@ -145,6 +145,10 @@
> #define SDMMC_IDMAC_ENABLE BIT(7)
> #define SDMMC_IDMAC_FB BIT(1)
> #define SDMMC_IDMAC_SWRESET BIT(0)
> +
> +/* Hardware Configuration(HCON) register */
> +#define SDMMC_HCON_IHR BIT(22)
> +
> /* Version ID register define */
> #define SDMMC_GET_VERID(x) ((x) & 0xFFFF)
> /* Card read threshold */
> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
> index 6ce7d2c..2b5b8bf 100644
> --- a/include/linux/mmc/dw_mmc.h
> +++ b/include/linux/mmc/dw_mmc.h
> @@ -191,6 +191,8 @@ struct dw_mci {
> struct regulator *vmmc; /* Power regulator */
> unsigned long irq_flags; /* IRQ flags */
> int irq;
> + u32 can_use_hold_reg;
> + bool use_hold_reg;
> };
>
> /* DMA ops for Internal/External DMAC interface */
> @@ -238,6 +240,7 @@ struct dw_mci_board {
> u32 caps; /* Capabilities */
> u32 caps2; /* More capabilities */
> u32 pm_caps; /* PM capabilities */
> + u32 cclk_in_drv; /*cclk_in_drv phase shift */
> /*
> * Override fifo depth. If 0, autodetect it from the FIFOTH register,
> * but note that this may not be reliable after a bootloader has used
> --
> 1.7.9.5
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
