Add dw_mmc-k3.c for k3v2, support sd/emmc
Signed-off-by: Zhangfei Gao <zhangfei.gao@xxxxxxxxxx>
Tested-by: Zhigang Wang <brooke.wangzhigang@xxxxxxxxxx>
---
.../devicetree/bindings/mmc/k3-dw-mshc.txt | 66 ++++
drivers/mmc/host/Kconfig | 10 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/dw_mmc-k3.c | 392 ++++++++++++++++++++
4 files changed, 469 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
create mode 100644 drivers/mmc/host/dw_mmc-k3.c
diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
new file mode 100644
index 0000000..54a9d8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
@@ -0,0 +1,66 @@
+* Hisilicon specific extensions to the Synopsis Designware Mobile
+ Storage Host Controller
+
+Read synopsis-dw-mshc.txt for more details
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsis dw mshc controller properties described
+by synopsis-dw-mshc.txt and the properties used by the Hisilicon specific
+extensions to the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+ - "hisilicon,hi4511-dw-mshc": for controllers with hi4511
+ specific extentions.
+* vmmc-supply: should be vmmc used in dwmmc
+* fifo-depth: should be provided if register can not provide correct value
+* clken-reg: should be clock enable register and offset
+* drv-sel-reg: should be driver delay select register and offset
+* sam-sel-reg: should be sample delay select register and offset
+* div-reg: should be divider register and offset
+
+Example:
+
+ The MSHC controller node can be split into two portions, SoC specific and
+ board specific portions as listed below.
+
+ dwmmc_0: dwmmc0@fcd03000 {
+ compatible = "hisilicon,hi4511-dw-mshc";
+ reg = <0xfcd03000 0x1000>;
+ interrupts = <0 16 4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clk_sd>, <&clk_ddrc_per>;
+ clock-names = "ciu", "biu";
+ clken-reg = <0x1f8 0>;
+ drv-sel-reg = <0x1f8 4>;
+ sam-sel-reg = <0x1f8 8>;
+ div-reg = <0x1f8 1>;
+ };
+ dwmmc0@fcd03000 {
+ num-slots = <1>;
+ vmmc-supply = <&ldo12>;
+ fifo-depth = <0x100>;
+ supports-highspeed;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd_pmx_pins &sd_cfg_func1 &sd_cfg_func2>;
+ cd-gpio = <&gpio10 3 0>;
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+ };
+
+PCTRL:
+
+Required Properties:
+* compatible: should be
+ - "hisilicon,pctrl": Peripheral control
+
+Example:
+
+ pctrl: pctrl@fca09000 {
+ compatible = "hisilicon,pctrl";
+ reg = <0xfca09000 0x1000>;
+ };
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 7fc5099..45aaa2d 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -575,6 +575,16 @@ config MMC_DW_SOCFPGA
This selects support for Altera SoCFPGA specific extensions to the
Synopsys DesignWare Memory Card Interface driver.
+config MMC_DW_K3
+ tristate "K3 specific extensions for Synopsys DW Memory Card Interface"
+ depends on MMC_DW
+ select MMC_DW_PLTFM
+ select MMC_DW_IDMAC
+ help
+ This selects support for Hisilicon K3 SoC specific extensions to the
+ Synopsys DesignWare Memory Card Interface driver. Select this option
+ for platforms based on Hisilicon K3 SoC's.
+
config MMC_DW_PCI
tristate "Synopsys Designware MCI support on PCI bus"
depends on MMC_DW && PCI
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index c41d0c3..64f5f8d 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_MMC_DW) += dw_mmc.o
obj-$(CONFIG_MMC_DW_PLTFM) += dw_mmc-pltfm.o
obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o
obj-$(CONFIG_MMC_DW_SOCFPGA) += dw_mmc-socfpga.o
+obj-$(CONFIG_MMC_DW_K3) += dw_mmc-k3.o
obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o
obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o
obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
diff --git a/drivers/mmc/host/dw_mmc-k3.c b/drivers/mmc/host/dw_mmc-k3.c
new file mode 100644
index 0000000..f46453f
--- /dev/null
+++ b/drivers/mmc/host/dw_mmc-k3.c
@@ -0,0 +1,392 @@
+/*
+ * Copyright (c) 2013 Linaro Ltd.
+ * Copyright (c) 2013 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/dw_mmc.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/of_address.h>
+
+#include "dw_mmc.h"
+#include "dw_mmc-pltfm.h"
+
+#define DRIVER_NAME "dwmmc_k3"
+
+enum dw_mci_k3_type {
+ DW_MCI_TYPE_HI4511,
+};
+
+static struct dw_mci_k3_compatible {
+ char *compatible;
+ enum dw_mci_k3_type type;
+} k3_compat[] = {
+ {
+ .compatible = "hisilicon,hi4511-dw-mshc",
+ .type = DW_MCI_TYPE_HI4511,
+ },
+};
+
+struct dw_mci_k3_priv_data {
+ enum dw_mci_k3_type type;
+ int old_timing;
+ u32 id;
+ u32 gpio_cd;
+ u32 clken_reg;
+ u32 clken_bit;
+ u32 sam_sel_reg;
+ u32 sam_sel_bit;
+ u32 drv_sel_reg;
+ u32 drv_sel_bit;
+ u32 div_reg;
+ u32 div_bit;
+};
+
+static void __iomem *pctrl;
+static DEFINE_SPINLOCK(mmc_tuning_lock);
+static int k3_tuning_config[][8][6] = {
+ /* bus_clk, div, drv_sel, sam_sel_max, sam_sel_min, input_clk */
+ {
+ {180000000, 6, 6, 13, 13, 25000000}, /* 0: LEGACY 400k */
+ {0}, /* 1: MMC_HS */
+ {360000000, 6, 4, 2, 0, 50000000 }, /* 2: SD_HS */
+ {180000000, 6, 4, 13, 13, 25000000}, /* 3: SDR12 */
+ {360000000, 6, 4, 2, 0, 50000000 }, /* 4: SDR25 */
+ {720000000, 6, 1, 9, 4, 100000000 }, /* 5: SDR50 */
+ {0}, /* 6: SDR104 */
+ {360000000, 7, 1, 3, 0, 50000000 }, /* 7: DDR50 */
+ }, {
+ {26000000, 1, 1, 3, 3, 13000000 }, /* 0: LEGACY 400k */
+ {360000000, 6, 3, 3, 1, 50000000 }, /* 1: MMC_HS*/
+ {0}, /* 2: SD_HS */
+ {0}, /* 3: SDR12 */
+ {26000000, 1, 1, 3, 3, 13000000 }, /* 4: SDR25 */
+ {360000000, 6, 3, 3, 1, 50000000 }, /* 5: SDR50 */
+ {0}, /* 6: SDR104 */
+ {720000000, 6, 4, 8, 4, 100000000}, /* 7: DDR50 */
+ },
+};
+
+static void dw_mci_k3_set_timing(struct dw_mci_k3_priv_data *priv,
+ int idx, int sam, int drv, int div)
+{
+ unsigned int clken_reg = priv->clken_reg;
+ unsigned int clken_bit = priv->clken_bit;
+ unsigned int sam_sel_reg = priv->sam_sel_reg;
+ unsigned int sam_sel_bit = priv->sam_sel_bit;
+ unsigned int drv_sel_reg = priv->drv_sel_reg;
+ unsigned int drv_sel_bit = priv->drv_sel_bit;
+ unsigned int div_reg = priv->div_reg;
+ unsigned int div_bit = priv->div_bit;
+ int i = 0;
+ unsigned int temp_reg;
+ unsigned long flags;
+
+ spin_lock_irqsave(&mmc_tuning_lock, flags);
+
+ /* disable clock */
+ temp_reg = readl(pctrl + clken_reg);
+ temp_reg &= ~(1<<clken_bit);
+ writel(temp_reg, pctrl + clken_reg);
+
+ temp_reg = readl(pctrl + sam_sel_reg);
+ if (sam >= 0) {
+ /* set sam delay */
+ for (i = 0; i < 4; i++) {
+ if (sam % 2)
+ temp_reg |= 1<<(sam_sel_bit + i);
+ else
+ temp_reg &= ~(1<<(sam_sel_bit + i));
+ sam = sam >> 1;
+ }
+ }
+ writel(temp_reg, pctrl + sam_sel_reg);
+
+ temp_reg = readl(pctrl + drv_sel_reg);
+ if (drv >= 0) {
+ /* set drv delay */
+ for (i = 0; i < 4; i++) {
+ if (drv % 2)
+ temp_reg |= 1<<(drv_sel_bit + i);
+ else
+ temp_reg &= ~(1<<(drv_sel_bit + i));
+ drv = drv >> 1;
+ }
+ }
+ writel(temp_reg, pctrl + drv_sel_reg);
+
+ temp_reg = readl(pctrl + div_reg);
+ if (div >= 0) {
+ /* set drv delay */
+ for (i = 0; i < 3; i++) {
+ if (div % 2)
+ temp_reg |= 1<<(div_bit + i);
+ else
+ temp_reg &= ~(1<<(div_bit + i));
+ div = div >> 1;
+ }
+ }
+ writel(temp_reg, pctrl + div_reg);
+
+ /* enable clock */
+ temp_reg = readl(pctrl + clken_reg);
+ temp_reg |= 1<<clken_bit;
+ writel(temp_reg, pctrl + clken_reg);
+
+ spin_unlock_irqrestore(&mmc_tuning_lock, flags);
+}
+
+static void dw_mci_k3_tun(struct dw_mci *host, int id, int index)
+{
+ struct dw_mci_k3_priv_data *priv = host->priv;
+ int ret;
+
+ if (!pctrl)
+ return;
+
+ if (priv->old_timing == index)
+ return;
+
+ ret = clk_set_rate(host->ciu_clk, k3_tuning_config[id][index][0]);
+ if (ret)
+ dev_err(host->dev, "clk_set_rate failed\n");
+
+ dw_mci_k3_set_timing(priv, id,
+ (k3_tuning_config[id][index][3] +
+ k3_tuning_config[id][index][4]) / 2,
+ k3_tuning_config[id][index][2],
+ k3_tuning_config[id][index][1]);
+
+ host->bus_hz = k3_tuning_config[id][index][5];
+ priv->old_timing = index;
+}
+
+static void dw_mci_k3_set_ios(struct dw_mci *host, struct mmc_ios *ios)
+{
+ struct dw_mci_k3_priv_data *priv = host->priv;
+ int id = priv->id;
+
+ if (priv->type == DW_MCI_TYPE_HI4511)
+ dw_mci_k3_tun(host, id, ios->timing);
+}
+
+static int dw_mci_k3_priv_init(struct dw_mci *host)
+{
+ struct dw_mci_k3_priv_data *priv;
+ int i;
+
+ priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv) {
+ dev_err(host->dev, "mem alloc failed for private data\n");
+ return -ENOMEM;
+ }
+ priv->id = of_alias_get_id(host->dev->of_node, "mshc");
+ priv->old_timing = -1;
+ host->priv = priv;
+
+ for (i = 0; i < ARRAY_SIZE(k3_compat); i++) {
+ if (of_device_is_compatible(host->dev->of_node,
+ k3_compat[i].compatible))
+ priv->type = k3_compat[i].type;
+ }
+
+ if (priv->type == DW_MCI_TYPE_HI4511) {
+ if (!pctrl) {
+ struct device_node *node;
+
+ node = of_find_compatible_node(NULL, NULL,
+ "hisilicon,pctrl");
+ pctrl = of_iomap(node, 0);
+ }
+ }
+
+ return 0;
+}
+
+static int dw_mci_k3_setup_clock(struct dw_mci *host)
+{
+ struct dw_mci_k3_priv_data *priv = host->priv;
+
+ if (priv->type == DW_MCI_TYPE_HI4511)
+ dw_mci_k3_tun(host, priv->id, MMC_TIMING_LEGACY);
+
+ return 0;
+}
+
+
+static irqreturn_t dw_mci_k3_card_detect(int irq, void *data)
+{
+ struct dw_mci *host = (struct dw_mci *)data;
+
+ queue_work(host->card_workqueue, &host->card_work);
+ return IRQ_HANDLED;
+};
+
+static int dw_mci_k3_get_cd(struct dw_mci *host, u32 slot_id)
+{
+ unsigned int status;
+ struct dw_mci_k3_priv_data *priv = host->priv;
+
+ status = !gpio_get_value(priv->gpio_cd);
+ return status;
+}
+
+static int dw_mci_k3_parse_dt(struct dw_mci *host)
+{
+ struct dw_mci_k3_priv_data *priv = host->priv;
+ struct device_node *np = host->dev->of_node;
+ u32 data[2];
+ int ret;
+
+ if (priv->type == DW_MCI_TYPE_HI4511) {
+ ret = of_property_read_u32_array(np,
+ "clken-reg", data, 2);
+ if (!ret) {
+ priv->clken_reg = data[0];
+ priv->clken_bit = data[1];
+ }
+
+ ret = of_property_read_u32_array(np,
+ "drv-sel-reg", data, 2);
+ if (!ret) {
+ priv->drv_sel_reg = data[0];
+ priv->drv_sel_bit = data[1];
+ }
+
+ ret = of_property_read_u32_array(np,
+ "sam-sel-reg", data, 2);
+ if (!ret) {
+ priv->sam_sel_reg = data[0];
+ priv->sam_sel_bit = data[1];
+ }
+
+ ret = of_property_read_u32_array(np,
+ "div-reg", data, 2);
+ if (!ret) {
+ priv->div_reg = data[0];
+ priv->div_bit = data[1];
+ }
+ }
+
+ return 0;
+}
+
+static unsigned long k3_dwmmc_caps[4] = {
+ MMC_CAP_4_BIT_DATA | MMC_CAP_SD_HIGHSPEED,
+ MMC_CAP_8_BIT_DATA | MMC_CAP_MMC_HIGHSPEED,
+ 0,
+ 0,
+};
+
+static const struct dw_mci_drv_data k3_drv_data = {
+ .caps = k3_dwmmc_caps,
+ .init = dw_mci_k3_priv_init,
+ .set_ios = dw_mci_k3_set_ios,
+ .setup_clock = dw_mci_k3_setup_clock,
+ .parse_dt = dw_mci_k3_parse_dt,
+};
+
+static const struct of_device_id dw_mci_k3_match[] = {
+ { .compatible = "hisilicon,hi4511-dw-mshc",
+ .data = &k3_drv_data, },
+ {},
+};
+MODULE_DEVICE_TABLE(of, dw_mci_k3_match);
+
+int dw_mci_k3_probe(struct platform_device *pdev)
+{
+ const struct dw_mci_drv_data *drv_data;
+ const struct of_device_id *match;
+ struct dw_mci *host;
+ int gpio, err;
+
+ match = of_match_node(dw_mci_k3_match, pdev->dev.of_node);
+ drv_data = match->data;
+
+ err = dw_mci_pltfm_register(pdev, drv_data);
+ if (err)
+ return err;
+
+ host = platform_get_drvdata(pdev);
+ if (host->pdata->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
+ return 0;
+
+ gpio = of_get_named_gpio(pdev->dev.of_node, "cd-gpio", 0);
+ if (gpio_is_valid(gpio)) {
+ if (devm_gpio_request(host->dev, gpio, "dw-mci-cd")) {
+ dev_err(host->dev, "gpio [%d] request failed\n", gpio);
+ } else {
+ struct dw_mci_k3_priv_data *priv = host->priv;
+ priv->gpio_cd = gpio;
+ host->pdata->get_cd = dw_mci_k3_get_cd;
+ err = devm_request_irq(host->dev, gpio_to_irq(gpio),
+ dw_mci_k3_card_detect,
+ IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+ DRIVER_NAME, host);
+ if (err)
+ dev_warn(mmc_dev(host->dev), "request gpio irq error\n");
+ }
+
+ } else {
+ dev_info(host->dev, "cd gpio not available");
+ }
+ return 0;
+}
+
+static int dw_mci_k3_suspend(struct device *dev)
+{
+ int ret;
+ struct dw_mci *host = dev_get_drvdata(dev);
+
+ ret = dw_mci_suspend(host);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int dw_mci_k3_resume(struct device *dev)
+{
+ int ret;
+ struct dw_mci *host = dev_get_drvdata(dev);
+ struct dw_mci_k3_priv_data *priv = host->priv;
+
+ if (priv->type == DW_MCI_TYPE_HI4511) {
+ int id = priv->id;
+
+ priv->old_timing = -1;
+ dw_mci_k3_tun(host, id, MMC_TIMING_LEGACY);
+ }
+
+ ret = dw_mci_resume(host);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+SIMPLE_DEV_PM_OPS(dw_mci_k3_pmops, dw_mci_k3_suspend, dw_mci_k3_resume);
+
+static struct platform_driver dw_mci_k3_pltfm_driver = {
+ .probe = dw_mci_k3_probe,
+ .remove = dw_mci_pltfm_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = dw_mci_k3_match,
+ .pm = &dw_mci_k3_pmops,
+ },
+};
+
+module_platform_driver(dw_mci_k3_pltfm_driver);
+
+MODULE_DESCRIPTION("K3 Specific DW-MSHC Driver Extension");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
