Hi Jackey, no, the cw1200 chip is a SDIO < 2.0 device. Kind regards, Johan 2012/12/14 Shen, Jackey <Jackey.Shen@xxxxxxx>: > Hi Johan, > > Is the SDIO WLAN chip (cw1200), you mentioned, SDIO 3.0 device with SDIO interface? > > Thanks, > Jackey > > -----Original Message----- > From: linux-mmc-owner@xxxxxxxxxxxxxxx [mailto:linux-mmc-owner@xxxxxxxxxxxxxxx] On Behalf Of Johan Rudholm > Sent: Saturday, December 08, 2012 12:20 AM > To: linux-mmc@xxxxxxxxxxxxxxx; Chris Ball > Cc: Per Forlin; Ulf Hansson; Fredrik Soderstedt; Kevin Liu; Philip Rakity; Daniel Drake; Aaron; Subhash Jadavani; Johan Rudholm > Subject: [PATCH 0/3] Signal voltage switch procedure for UHS mode > > This patch series attempts to make the 1.8V signal voltage switch required for UHS mode work according to the SD specification. > > These patches have been tested with a couple of UHS SD cards, one of which sometimes requires up to five power cycles before it accepts the signal voltage switch. The patches have also been tested with various other SD cards, as well as one SDIO WLAN chip (cw1200) to check for regressions. The patches have also been tested with CONFIG_MMC_CLKGATE. > > As usual, I'd be very grateful if someone could help me test this patch with an UHS SDIO card and perhaps also a combo card (which does seem to be rare these days?)? > > This patch series is based on previous RFC/patch: > > [RFC/PATCH v2] mmc: core: Fixup signal voltage switch > > Changelog: > v2 -> This patch series > - Removed the extra argument to the card_busy host_ops function > - Added mmc_power_cycle > - Some clarifying comments > v1 -> v2 > - Removed reset of signal voltage in mmc_sd_get_cid, since > "mmc: core: reset signal voltage on power up" > previous two patches -> v1: > - Keep calls to mmc_host_clk_hold / mmc_host_clk_release > - Add retry-loop / power cycle in sdio.c > - Fall back to 3.3 V if the switch repeatedly fails > - Add an extra argument to the card_busy host_ops function, > which can be used to signal polling use of the function > > Johan Rudholm (3): > mmc: core: Add mmc_power_cycle > mmc: core: Add card_busy to host_ops > mmc: core: Fixup signal voltage switch > > drivers/mmc/core/core.c | 43 +++++++++++++++++++++++++++++++++++++++++++ > drivers/mmc/core/core.h | 1 + > drivers/mmc/core/sd.c | 26 +++++++++++++++++++++----- > drivers/mmc/core/sdio.c | 25 +++++++++++++++++++++++-- > include/linux/mmc/host.h | 3 +++ > 5 files changed, 91 insertions(+), 7 deletions(-) > > -- > 1.7.10 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
