On Tuesday, August 29, 2012, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
> On 08/29/2012 10:21 AM, Seungwon Jeon wrote:
> > On Tuesday, August 28, 2012, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
> >> synopsys spec is mentioned. (7.1 Software/Hardware Restrictions)
> >> "Before disabling clock, ensure that card is not busy due to any previous data command."
> >>
> >> At specific board, i found the problem that didn't inform ciu.
> >> (It didn't produce always.)
> >> At that time, i checked the status register whether card is busy or not.
> >> (Start bit of CMD register is cleared, but card is busy.)
> >> Current code didn't check the card status. Just check whether the start-bit cleared.
> >> host regard that command is completed, will send the next command.
> >> But next command didn't issue because Card is busy.
> >> This patch can prevent this situation.
> >>
> >> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
> >> ---
> >> drivers/mmc/host/dw_mmc.c | 27 +++++++++++++++++++++------
> >> drivers/mmc/host/dw_mmc.h | 1 +
> >> 2 files changed, 22 insertions(+), 6 deletions(-)
> >>
> >> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> >> index 36f98c0..e30d3ed 100644
> >> --- a/drivers/mmc/host/dw_mmc.c
> >> +++ b/drivers/mmc/host/dw_mmc.c
> >> @@ -623,6 +623,24 @@ static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
> >> cmd, arg, cmd_status);
> >> }
> >>
> >> +static void dw_mci_inform_ciu(struct dw_mci_slot *slot)
> >> +{
> >> + struct dw_mci *host = slot->host;
> >> + unsigned long timeout = jiffies + msecs_to_jiffies(10);
> > 10ms is from test?
> It's tested...it's not exactly value..but never spent the time.
> >
> >> + u32 ctrl, status;
> >> +
> >> + do {
> >> + status = mci_readl(host, STATUS);
> >> + if (!(status & SDMMC_DATA_BUSY))
> >> + break;
> >> + ctrl = mci_readl(host, CTRL);
> >> + ctrl |= SDMMC_CTRL_RESET;
> >> + mci_writel(host, CTRL, ctrl);
> >> + } while (time_before(jiffies, timeout));
> >> +
> >> + mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> +}
> >> +
> >> static void dw_mci_setup_bus(struct dw_mci_slot *slot)
> >> {
> >> struct dw_mci *host = slot->host;
> >> @@ -650,15 +668,13 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot)
> > According to your quotation of manual("Before disabling clock, ...),
> > Place of dw_mci_inform_ciu is proper here?
> manual is mentioned "before the disabling clock". but i think no problem before send the command.
> >
> > dw_mci_inform_ciu(slot);
> >
> > /* disable clock */
> > mci_writel(host, CLKENA, 0);
> > mci_writel(host, CLKSRC, 0);
> >
> >> mci_writel(host, CLKSRC, 0);
> >>
> >> /* inform CIU */
> >> - mci_send_cmd(slot,
> >> - SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> + dw_mci_inform_ciu(slot);
> >>
> >> /* set clock to desired speed */
> >> mci_writel(host, CLKDIV, div);
> >>
> >> /* inform CIU */
> >> - mci_send_cmd(slot,
> >> - SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> + dw_mci_inform_ciu(slot);
> > And then, since start to change clock sequence, there is no need to check busy-status.
> > Just need to update clock with origin code.
> Right, didn't check the busy-status. but there is also no reason that didn't need to check busy-status.
Ok, I mentioned no check busy-status because host doesn't send command to card in the middle of host's clock update.
If you have a opinion, please let me know.
Thanks,
Seungwon Jeon
> >>
> >> /* enable clock; only low power if no SDIO */
> >> clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
> >> @@ -667,8 +683,7 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot)
> >> mci_writel(host, CLKENA, clk_en_a);
> >>
> >> /* inform CIU */
> >> - mci_send_cmd(slot,
> >> - SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
> >> + dw_mci_inform_ciu(slot);
> > Same here.
> >
> > Thanks,
> > Seungwon Jeon
> >>
> >> host->current_speed = slot->clock;
> >> }
> >> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
> >> index 15c27e1..b6a1a78 100644
> >> --- a/drivers/mmc/host/dw_mmc.h
> >> +++ b/drivers/mmc/host/dw_mmc.h
> >> @@ -127,6 +127,7 @@
> >> #define SDMMC_CMD_INDX(n) ((n) & 0x1F)
> >> /* Status register defines */
> >> #define SDMMC_GET_FCNT(x) (((x)>>17) & 0x1FFF)
> >> +#define SDMMC_DATA_BUSY BIT(9)
> >> /* Internal DMAC interrupt defines */
> >> #define SDMMC_IDMAC_INT_AI BIT(9)
> >> #define SDMMC_IDMAC_INT_NI BIT(8)
> >> --
> >> 1.7.4.1
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> > the body of a message to majordomo@xxxxxxxxxxxxxxx
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
