On 08/28/2012 10:58 PM, Thomas Abraham wrote:
> On 28 August 2012 13:25, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
>> This patch is added the use_hold_reg bit in CMD register.
>>
>> In upper version than 2.40a, bit[29] of CMD register is used the use_hold_reg.
>> Some SoC is affected by this bit.
>> (This bit means whether use hold register when send data and cmd.
>> And related with cclk_in_drv phase)
>>
>> Now i known that HOLD-register is using only Exynos-SoC.
>> But hold-register is supported basically feature at Synopsys-IP.
>> If Other SoC is used hold regster, we can change the _CLKSEL_REG_.
>>
>> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
>> Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
>> ---
>> drivers/mmc/host/dw_mmc.c | 36 ++++++++++++++++++++++++++++++++++++
>> drivers/mmc/host/dw_mmc.h | 1 +
>> include/linux/mmc/dw_mmc.h | 3 +++
>> 3 files changed, 40 insertions(+), 0 deletions(-)
>>
>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
>> index 437fdf8..3642455 100644
>> --- a/drivers/mmc/host/dw_mmc.c
>> +++ b/drivers/mmc/host/dw_mmc.c
>> @@ -265,11 +265,45 @@ static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
>> static void dw_mci_start_command(struct dw_mci *host,
>> struct mmc_command *cmd, u32 cmd_flags)
>> {
>> + struct dw_mci_slot *slot = host->cur_slot;
>> + struct mmc_ios *ios = &slot->mmc->ios;
>> +
>> host->cmd = cmd;
>> dev_vdbg(&host->dev,
>> "start command: ARGR=0x%08x CMDR=0x%08x\n",
>> cmd->arg, cmd_flags);
>>
>> + if (host->quirks & DW_MCI_QUIRK_USE_CLKSEL_REG) {
>> + /*
>> + * If use HOLD register and SDR12/SDSR25,
>> + * CMD and DATA sent to card through HOLD regster by default.
>> + * But if mode is SDR50/DDR50/SDR104,
>> + * only use the hold register when cclk_in_drv value is greater than 0.
>> + */
>> + switch (ios->timing) {
>> + case MMC_TIMING_UHS_SDR50:
>> + case MMC_TIMING_UHS_DDR50:
>> + case MMC_TIMING_UHS_SDR104:
>> + if (host->pdata->get_clk_drv &&
>> + host->pdata->get_clk_drv(host) &&
>> + host->use_hold_reg) {
>> + cmd_flags |= SDMMC_CMD_USE_HOLD_REG;
>> + break;
>> + }
>> +
>> + cmd_flags &= ~SDMMC_CMD_USE_HOLD_REG;
>> + break;
>> + case MMC_TIMING_UHS_SDR12:
>> + case MMC_TIMING_UHS_SDR25:
>> + if (host->use_hold_reg) {
>> + cmd_flags |= SDMMC_CMD_USE_HOLD_REG;
>> + break;
>> + }
>> + default:
>> + cmd_flags &= ~SDMMC_CMD_USE_HOLD_REG;
>> + }
>> + }
>> +
>> mci_writel(host, CMDARG, cmd->arg);
>> wmb();
>>
>> @@ -2015,6 +2049,8 @@ int dw_mci_probe(struct dw_mci *host)
>> host->data_shift = 2;
>> }
>>
>> + host->use_hold_reg = (mci_readl(host, HCON) >> 22) & 0x1;
>> +
>
> The presence of DW_MCI_QUIRK_USE_CLKSEL_REG quirk should be sufficient
> condition to know if HOLD_REG bit is supported on not. The setting of
> host->use_hold_reg as above creates a dependency on the boot loader to
> setup the controller appropriately.
Dependency on the bootloader? I known that HCON's type is read only.
It didn't have any dependency with bootloader.
>
> Thanks,
> Thomas.
>
>
>> /* Reset all blocks */
>> if (!mci_wait_reset(&host->dev, host))
>> return -ENODEV;
>> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
>> index b6a1a78..cc905ee 100644
>> --- a/drivers/mmc/host/dw_mmc.h
>> +++ b/drivers/mmc/host/dw_mmc.h
>> @@ -111,6 +111,7 @@
>> #define SDMMC_INT_ERROR 0xbfc2
>> /* Command register defines */
>> #define SDMMC_CMD_START BIT(31)
>> +#define SDMMC_CMD_USE_HOLD_REG BIT(29)
>> #define SDMMC_CMD_CCS_EXP BIT(23)
>> #define SDMMC_CMD_CEATA_RD BIT(22)
>> #define SDMMC_CMD_UPD_CLK BIT(21)
>> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
>> index f20979c..803a80d 100644
>> --- a/include/linux/mmc/dw_mmc.h
>> +++ b/include/linux/mmc/dw_mmc.h
>> @@ -156,6 +156,7 @@ struct dw_mci {
>> u32 fifoth_val;
>> u16 verid;
>> u16 data_offset;
>> + bool use_hold_reg;
>> struct device dev;
>> struct dw_mci_board *pdata;
>> struct dw_mci_slot *slot[MAX_MCI_SLOTS];
>> @@ -201,6 +202,8 @@ struct dw_mci_dma_ops {
>> #define DW_MCI_QUIRK_HIGHSPEED BIT(2)
>> /* Unreliable card detection */
>> #define DW_MCI_QUIRK_BROKEN_CARD_DETECTION BIT(3)
>> +/* To use the CLKSEL register for phase-shift */
>> +#define DW_MCI_QUIRK_USE_CLKSEL_REG BIT(4)
>>
>>
>> struct dma_pdata;
>> --
>> 1.7.4.1
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
