On 17:15 Thu 24 May , ludovic.desroches@xxxxxxxxx wrote:
> From: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>
>
> Signed-off-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>
> ---
> .../devicetree/bindings/mmc/atmel-hsmci.txt | 67 +++++++++++++++
> drivers/mmc/host/atmel-mci.c | 85 +++++++++++++++++++-
> 2 files changed, 150 insertions(+), 2 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
>
> diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
> new file mode 100644
> index 0000000..81c20cc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
> @@ -0,0 +1,67 @@
> +* Atmel High Speed MultiMedia Card Interface
> +
> +This controller on atmel products provides an interface for MMC, SD and SDIO
> +types of memory cards.
> +
> +1) MCI node
> +
> +Required properties:
> +- compatible: no blank "atmel,hsmci"
> +- reg: should contain HSMCI registers location and length
> +- interrupts: should contain HSMCI interrupt number
> +- #address-cells: should be one. The cell is the slot id.
> +- #size-cells: should be zero.
> +- at least one slot node
> +
> +The node contains child nodes for each slot that the platform uses
> +
> +Example MCI node:
> +
> +mmc0: mmc@f0008000 {
> + compatible = "atmel,hsmci";
> + reg = <0xf0008000 0x600>;
> + interrupts = <12 4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + [ child node definitions...]
> +};
> +
> +2) slot nodes
> +
> +Required properties:
> +- reg: should contain the slot id.
> +- bus-width: number of data lines connected to the controller
> +
> +Optional properties:
> +- cd-gpios: specify GPIOs for card detection
> +- cd-inverted: invert the value of external card detect gpio line
> +- wp-gpios: specify GPIOs for write protection
> +
> +Example slot node:
> +
> +slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 15 0>
> + cd-inverted;
> +};
> +
> +Example full MCI node:
> +mmc0: mmc@f0008000 {
> + compatible = "atmel,hsmci";
> + reg = <0xf0008000 0x600>;
> + interrupts = <12 4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 15 0>
> + cd-inverted;
> + };
> + slot@1 {
> + reg = <1>;
> + bus-width = <4>;
> + };
> +};
> diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
> index f2c115e..47421fc 100644
> --- a/drivers/mmc/host/atmel-mci.c
> +++ b/drivers/mmc/host/atmel-mci.c
> @@ -19,6 +19,9 @@
> #include <linux/interrupt.h>
> #include <linux/ioport.h>
> #include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <linux/platform_device.h>
> #include <linux/scatterlist.h>
> #include <linux/seq_file.h>
> @@ -493,6 +496,70 @@ err:
> dev_err(&mmc->class_dev, "failed to initialize debugfs for slot\n");
> }
>
> +#if defined(CONFIG_OF)
> +static const struct of_device_id atmci_dt_ids[] = {
> + { .compatible = "atmel,hsmci" },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmci_dt_ids);
> +
> +static struct mci_platform_data __devinit*
> +atmci_of_init(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct device_node *cnp;
> + struct mci_platform_data *pdata;
> + u32 slot_id;
> +
> + if (!np) {
> + dev_err(&pdev->dev, "device node not found\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
> + if (!pdata) {
> + dev_err(&pdev->dev, "could not allocate memory for pdata\n");
> + return ERR_PTR(-ENOMEM);
> + }
> +
> + for_each_child_of_node(np, cnp) {
> + if (of_property_read_u32(cnp, "reg", &slot_id)) {
> + dev_warn(&pdev->dev, "reg property is missing for %s\n",
> + cnp->full_name);
> + continue;
> + }
> +
> + if (slot_id >= ATMCI_MAX_NR_SLOTS) {
> + dev_warn(&pdev->dev, "can't have more than %d slots\n",
> + ATMCI_MAX_NR_SLOTS);
> + break;
> + }
> +
> + if (of_property_read_u32(cnp, "bus-width",
> + &pdata->slot[slot_id].bus_width))
> + pdata->slot[slot_id].bus_width = 1;
> +
> + pdata->slot[slot_id].detect_pin =
> + of_get_named_gpio(cnp, "cd-gpios", 0);
> +
> + pdata->slot[slot_id].detect_is_active_high =
> + of_property_read_bool(cnp, "cd-inverted");
as this is going to be removed at once
please implement the gpio active low too
otherwise
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@xxxxxxxxxxxx>
Best Regards,
J.
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
