Power on the CN11 and CN12 SD/MMC slots on ecovec is controlled by GPIOs,
which makes it possible to use the fixed voltage regulator driver to switch
card power on and off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@xxxxxx>
---
arch/sh/boards/mach-ecovec24/setup.c | 85 ++++++++++++++++++++++++---------
1 files changed, 62 insertions(+), 23 deletions(-)
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index dbedfda..5ba295d 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -19,6 +19,9 @@
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/delay.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <linux/usb/r8a66597.h>
#include <linux/usb/renesas_usbhs.h>
#include <linux/i2c.h>
@@ -518,12 +521,66 @@ static struct i2c_board_info ts_i2c_clients = {
.irq = IRQ0,
};
+static struct regulator_consumer_supply cn12_power_consumers[] =
+{
+ REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+ REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+};
+
+static struct regulator_init_data cn12_power_init_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(cn12_power_consumers),
+ .consumer_supplies = cn12_power_consumers,
+};
+
+static struct fixed_voltage_config cn12_power_info = {
+ .supply_name = "CN12 SD/MMC Vdd",
+ .microvolts = 3300000,
+ .gpio = GPIO_PTB7,
+ .enable_high = 1,
+ .init_data = &cn12_power_init_data,
+};
+
+static struct platform_device cn12_power = {
+ .name = "reg-fixed-voltage",
+ .id = 0,
+ .dev = {
+ .platform_data = &cn12_power_info,
+ },
+};
+
#if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
/* SDHI0 */
-static void sdhi0_set_pwr(struct platform_device *pdev, int state)
+static struct regulator_consumer_supply sdhi0_power_consumers[] =
{
- gpio_set_value(GPIO_PTB6, state);
-}
+ REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_init_data sdhi0_power_init_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(sdhi0_power_consumers),
+ .consumer_supplies = sdhi0_power_consumers,
+};
+
+static struct fixed_voltage_config sdhi0_power_info = {
+ .supply_name = "CN11 SD/MMC Vdd",
+ .microvolts = 3300000,
+ .gpio = GPIO_PTB6,
+ .enable_high = 1,
+ .init_data = &sdhi0_power_init_data,
+};
+
+static struct platform_device sdhi0_power = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &sdhi0_power_info,
+ },
+};
static int sdhi0_get_cd(struct platform_device *pdev)
{
@@ -533,7 +590,6 @@ static int sdhi0_get_cd(struct platform_device *pdev)
static struct sh_mobile_sdhi_info sdhi0_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
- .set_pwr = sdhi0_set_pwr,
.tmio_caps = MMC_CAP_SDIO_IRQ | MMC_CAP_POWER_OFF_CARD |
MMC_CAP_NEEDS_POLL,
.get_cd = sdhi0_get_cd,
@@ -564,11 +620,6 @@ static struct platform_device sdhi0_device = {
#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
/* SDHI1 */
-static void sdhi1_set_pwr(struct platform_device *pdev, int state)
-{
- gpio_set_value(GPIO_PTB7, state);
-}
-
static int sdhi1_get_cd(struct platform_device *pdev)
{
return !gpio_get_value(GPIO_PTW7);
@@ -579,7 +630,6 @@ static struct sh_mobile_sdhi_info sdhi1_info = {
.dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
.tmio_caps = MMC_CAP_SDIO_IRQ | MMC_CAP_POWER_OFF_CARD |
MMC_CAP_NEEDS_POLL,
- .set_pwr = sdhi1_set_pwr,
.get_cd = sdhi1_get_cd,
};
@@ -899,11 +949,6 @@ static struct platform_device vou_device = {
#if defined(CONFIG_MMC_SH_MMCIF) || defined(CONFIG_MMC_SH_MMCIF_MODULE)
/* SH_MMCIF */
-static void mmcif_set_pwr(struct platform_device *pdev, int state)
-{
- gpio_set_value(GPIO_PTB7, state);
-}
-
static struct resource sh_mmcif_resources[] = {
[0] = {
.name = "SH_MMCIF",
@@ -924,12 +969,10 @@ static struct resource sh_mmcif_resources[] = {
};
static struct sh_mmcif_plat_data sh_mmcif_plat = {
- .set_pwr = mmcif_set_pwr,
.sup_pclk = 0, /* SH7724: Max Pclk/2 */
.caps = MMC_CAP_4_BIT_DATA |
MMC_CAP_8_BIT_DATA |
MMC_CAP_NEEDS_POLL,
- .ocr = MMC_VDD_32_33 | MMC_VDD_33_34,
};
static struct platform_device sh_mmcif_device = {
@@ -954,7 +997,9 @@ static struct platform_device *ecovec_devices[] __initdata = {
&ceu0_device,
&ceu1_device,
&keysc_device,
+ &cn12_power,
#if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
+ &sdhi0_power,
&sdhi0_device,
#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
&sdhi1_device,
@@ -1252,8 +1297,6 @@ static int __init arch_setup(void)
gpio_request(GPIO_FN_SDHI0D2, NULL);
gpio_request(GPIO_FN_SDHI0D1, NULL);
gpio_request(GPIO_FN_SDHI0D0, NULL);
- gpio_request(GPIO_PTB6, NULL);
- gpio_direction_output(GPIO_PTB6, 0);
#else
/* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */
gpio_request(GPIO_FN_MSIOF0_TXD, NULL);
@@ -1282,8 +1325,6 @@ static int __init arch_setup(void)
gpio_request(GPIO_FN_MMC_D0, NULL);
gpio_request(GPIO_FN_MMC_CLK, NULL);
gpio_request(GPIO_FN_MMC_CMD, NULL);
- gpio_request(GPIO_PTB7, NULL);
- gpio_direction_output(GPIO_PTB7, 0);
cn12_enabled = true;
#elif defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
@@ -1295,8 +1336,6 @@ static int __init arch_setup(void)
gpio_request(GPIO_FN_SDHI1D2, NULL);
gpio_request(GPIO_FN_SDHI1D1, NULL);
gpio_request(GPIO_FN_SDHI1D0, NULL);
- gpio_request(GPIO_PTB7, NULL);
- gpio_direction_output(GPIO_PTB7, 0);
/* Card-detect, used on CN12 with SDHI1 */
gpio_request(GPIO_PTW7, NULL);
--
1.7.2.5
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
