> -----Original Message----- > From: Girish K S [mailto:girish.shivananjappa@xxxxxxxxxx] > Sent: Monday, December 19, 2011 4:20 PM > To: Subhash Jadavani > Cc: linux-mmc@xxxxxxxxxxxxxxx; patches@xxxxxxxxxx; linux-samsung- > soc@xxxxxxxxxxxxxxx; Chris Ball > Subject: Re: [PATCH V6 1/2] mmc: core: HS200 mode support for eMMC 4.5 > > On 19 December 2011 15:40, Subhash Jadavani <subhashj@xxxxxxxxxxxxxx> > wrote: > > Hi Girish, > > > > Overall this patch looks good. I have only 2 minor comments inline > below. > > > > Regards, > > Subhash > > > > > >> -----Original Message----- > >> From: linux-mmc-owner@xxxxxxxxxxxxxxx [mailto:linux-mmc- > >> owner@xxxxxxxxxxxxxxx] On Behalf Of Girish K S > >> Sent: Monday, December 19, 2011 12:07 PM > >> To: linux-mmc@xxxxxxxxxxxxxxx > >> Cc: patches@xxxxxxxxxx; linux-samsung-soc@xxxxxxxxxxxxxxx; Girish K > S; > >> Chris Ball > >> Subject: [PATCH V6 1/2] mmc: core: HS200 mode support for eMMC 4.5 > >> > >> This patch adds the support of the HS200 bus speed for eMMC 4.5 > >> devices. > >> The eMMC 4.5 devices have support for 200MHz bus speed. The function > >> prototype of the tuning function is modified to handle the tuning > >> command > >> number which is different in sd and mmc case. > >> > >> cc: Chris Ball <cjb@xxxxxxxxxx> > >> Signed-off-by: Girish K S <girish.shivananjappa@xxxxxxxxxx> > >> --- > >> drivers/mmc/core/bus.c | 3 +- > >> drivers/mmc/core/debugfs.c | 3 + > >> drivers/mmc/core/mmc.c | 147 > >> +++++++++++++++++++++++++++++++++++++++++--- > >> drivers/mmc/core/sd.c | 3 +- > >> drivers/mmc/core/sdio.c | 4 +- > >> include/linux/mmc/card.h | 3 + > >> include/linux/mmc/mmc.h | 66 +++++++++++++++++++- > >> 7 files changed, 216 insertions(+), 13 deletions(-) > >> > >> diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c > >> index f8a228a..5d011a3 100644 > >> --- a/drivers/mmc/core/bus.c > >> +++ b/drivers/mmc/core/bus.c > >> @@ -303,10 +303,11 @@ int mmc_add_card(struct mmc_card *card) > >> mmc_card_ddr_mode(card) ? "DDR " : "", > >> type); > >> } else { > >> - printk(KERN_INFO "%s: new %s%s%s card at address > %04x\n", > >> + pr_info("%s: new %s%s%s%s card at address %04x\n", > >> mmc_hostname(card->host), > >> mmc_card_uhs(card) ? "ultra high speed " : > >> (mmc_card_highspeed(card) ? "high speed " : > ""), > >> + (mmc_card_hs200(card) ? "HS200 " : ""), > >> mmc_card_ddr_mode(card) ? "DDR " : "", > >> type, card->rca); > >> } > >> diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c > >> index 027615d..9ab5b17 100644 > >> --- a/drivers/mmc/core/debugfs.c > >> +++ b/drivers/mmc/core/debugfs.c > >> @@ -135,6 +135,9 @@ static int mmc_ios_show(struct seq_file *s, void > >> *data) > >> case MMC_TIMING_UHS_DDR50: > >> str = "sd uhs DDR50"; > >> break; > >> + case MMC_TIMING_MMC_HS200: > >> + str = "mmc high-speed SDR200"; > >> + break; > >> default: > >> str = "invalid"; > >> break; > >> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c > >> index f0a9f1f..d5d93de 100644 > >> --- a/drivers/mmc/core/mmc.c > >> +++ b/drivers/mmc/core/mmc.c > >> @@ -286,6 +286,27 @@ static int mmc_read_ext_csd(struct mmc_card > *card, > >> u8 *ext_csd) > >> } > >> card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE]; > >> switch (ext_csd[EXT_CSD_CARD_TYPE] & EXT_CSD_CARD_TYPE_MASK) { > >> + case EXT_CSD_CARD_TYPE_SDR_ALL: > >> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V: > >> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V: > >> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52: > >> + card->ext_csd.hs_max_dtr = 200000000; > >> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_200; > >> + break; > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V_ALL: > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V: > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V: > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52: > >> + card->ext_csd.hs_max_dtr = 200000000; > >> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V; > >> + break; > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V_ALL: > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V: > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V: > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52: > >> + card->ext_csd.hs_max_dtr = 200000000; > >> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_8V; > >> + break; > >> case EXT_CSD_CARD_TYPE_DDR_52 | EXT_CSD_CARD_TYPE_52 | > >> EXT_CSD_CARD_TYPE_26: > >> card->ext_csd.hs_max_dtr = 52000000; > >> @@ -700,6 +721,52 @@ static int mmc_select_powerclass(struct > mmc_card > >> *card, > >> } > >> > >> /* > >> + * Selects the desired buswidth and switch to the HS200 mode > >> + * if bus width set without error > >> + */ > >> +static int mmc_select_hs200(struct mmc_card *card) > >> +{ > >> + int err = 0; > >> + struct mmc_host *host; > >> + u32 bus_width = MMC_BUS_WIDTH_4; > >> + > >> + BUG_ON(!card); > >> + > >> + host = card->host; > >> + > >> + /* > >> + * Host is capable of 8bit transfer, then switch > >> + * the device to work in 8bit transfer mode. If the > >> + * mmc switch command returns error then switch to > >> + * 4bit transfer mode. On success set the corresponding > >> + * bus width on the host. > >> + */ > >> + if (host->caps & MMC_CAP_8_BIT_DATA) { > >> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> + EXT_CSD_BUS_WIDTH, > >> + EXT_CSD_BUS_WIDTH_8, > >> + card->ext_csd.generic_cmd6_time); > >> + bus_width = MMC_BUS_WIDTH_8; > >> + } > >> + > >> + /* If the 8bit mode fails switch to 4 bit mode */ > >> + if (err) > >> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> + EXT_CSD_BUS_WIDTH, > >> + EXT_CSD_BUS_WIDTH_4, > >> + card->ext_csd.generic_cmd6_time); > > > > Don't you need to set the bus_width = MMC_BUS_WIDTH_4 after sending > the > > switch? > > Let's say if the host->caps says it support the 8-bit mode but > mmc_switch() > > fails but your bus_width will still be MMC_BUS_WIDTH_8. Now you try > to set > > the bus width to 4-bit which will succeed but bus_width variable is > not > > initialize to 4-bit yet. > > Thanks just missed it. > > > > > > > > >> + > >> + /* switch to HS200 mode if bus width set successfully */ > >> + if (!err) { > >> + mmc_set_bus_width(card->host, bus_width); > >> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> + EXT_CSD_HS_TIMING, 2, 0); > >> + } > >> + > >> + return err; > >> +} > >> + > >> +/* > >> * Handle the detection and initialisation of a card. > >> * > >> * In the case of a resume, "oldcard" will contain the card > >> @@ -905,11 +972,15 @@ static int mmc_init_card(struct mmc_host > *host, > >> u32 ocr, > >> /* > >> * Activate high speed (if supported) > >> */ > >> - if ((card->ext_csd.hs_max_dtr != 0) && > >> - (host->caps & MMC_CAP_MMC_HIGHSPEED)) { > >> - err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> - EXT_CSD_HS_TIMING, 1, > >> - card->ext_csd.generic_cmd6_time); > >> + if (card->ext_csd.hs_max_dtr != 0) { > >> + err = 0; > >> + if ((card->ext_csd.hs_max_dtr > 52000000) && > >> + (host->caps2 & MMC_CAP2_HS200)) > >> + err = mmc_select_hs200(card); > >> + else if (host->caps & MMC_CAP_MMC_HIGHSPEED) > >> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> + EXT_CSD_HS_TIMING, 1, 0); > >> + > >> if (err && err != -EBADMSG) > >> goto free_card; > >> > >> @@ -918,8 +989,15 @@ static int mmc_init_card(struct mmc_host *host, > >> u32 ocr, > >> mmc_hostname(card->host)); > >> err = 0; > >> } else { > >> - mmc_card_set_highspeed(card); > >> - mmc_set_timing(card->host, MMC_TIMING_MMC_HS); > >> + if ((card->ext_csd.hs_max_dtr > 52000000) && > >> + (host->caps2 & MMC_CAP2_HS200)) { > >> + mmc_card_set_hs200(card); > >> + mmc_set_timing(card->host, > >> + MMC_TIMING_MMC_HS200); > >> + } else { > >> + mmc_card_set_highspeed(card); > >> + mmc_set_timing(card->host, > > MMC_TIMING_MMC_HS); > >> + } > >> } > >> } > >> > >> @@ -944,7 +1022,7 @@ static int mmc_init_card(struct mmc_host *host, > >> u32 ocr, > >> */ > >> max_dtr = (unsigned int)-1; > >> > >> - if (mmc_card_highspeed(card)) { > >> + if (mmc_card_highspeed(card) || mmc_card_hs200(card)) { > >> if (max_dtr > card->ext_csd.hs_max_dtr) > >> max_dtr = card->ext_csd.hs_max_dtr; > >> } else if (max_dtr > card->csd.max_dtr) { > >> @@ -970,9 +1048,60 @@ static int mmc_init_card(struct mmc_host > *host, > >> u32 ocr, > >> } > >> > >> /* > >> + * Indicate HS200 SDR mode (if supported). > >> + */ > >> + if (mmc_card_hs200(card)) { > >> + u32 ext_csd_bits; > >> + u32 bus_width = card->host->ios.bus_width; > >> + > >> + /* > >> + * For devices supporting HS200 mode, the bus width > has > >> + * to be set before executing the tuning function. If > >> + * set before tuning, then device will respond with > CRC > >> + * errors for responses on CMD line. So for HS200 the > >> + * sequence will be > >> + * 1. set bus width 4bit / 8 bit (1 bit not supported) > >> + * 2. switch to HS200 mode > >> + * 3. set the clock to > 52Mhz <=200MHz and > >> + * 4. execute tuning for HS200 > >> + */ > >> + if ((host->caps2 & MMC_CAP2_HS200) && > >> + card->host->ops->execute_tuning) > >> + err = card->host->ops->execute_tuning(card- > >host, > >> + MMC_SEND_TUNING_BLOCK_HS200); > >> + if (err) { > >> + pr_warning("tuning execution failed\n"); > >> + goto err; > >> + } > >> + > >> + ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ? > >> + EXT_CSD_BUS_WIDTH_8 : > >> + EXT_CSD_BUS_WIDTH_4; > >> + err = mmc_select_powerclass(card, ext_csd_bits, > ext_csd); > >> + if (err) { > >> + pr_err("%s: power class selection to bus > width" > >> + "%d failed\n", mmc_hostname(card- > >host), > >> + 1 << bus_width); > >> + goto err; > >> + } > >> + > >> + if ((card->ext_csd.card_type & > EXT_CSD_CARD_TYPE_SDR_1_2V) > >> + && (host->caps2 & MMC_CAP2_HS200_1_2V_SDR)) { > >> + err = mmc_set_signal_voltage(host, > >> + MMC_SIGNAL_VOLTAGE_120, 0); > > > > Shouldn't this voltage switch be done in mmc_select_hs200() before > selecting > > the bus width and timings? > > Will it affect the functionality?. Since it it IO voltage I think it > can be done here. And I am setting the Host specific timing and > buswidth again. > is ur intention to avoid setting timing and buswidth again? Actually both. execute_tuning should be run with actual I/O voltage in which card is going to run. But here you are first running the execute_tuning() may be at 3.3v/1.8v then changing the I/O voltage which I guess doesn't look correct. SD3.01 specification has specifically mentioned that first the I/O voltage switch should happen and then only execute_tuning() should happen. So it's better to check if the eMMC4.5 spec. also implies this restriction anywhere or not. > > > > > > > > > > > > >> + > >> + if (err) > >> + goto err; > >> + mmc_set_timing(card->host, > MMC_TIMING_MMC_HS200); > >> + mmc_set_bus_width(card->host, bus_width); > >> + } > >> + } > >> + > >> + /* > >> * Activate wide bus and DDR (if supported). > >> */ > >> - if ((card->csd.mmca_vsn >= CSD_SPEC_VER_4) && > >> + if (!mmc_card_hs200(card) && > >> + (card->csd.mmca_vsn >= CSD_SPEC_VER_3) && > >> (host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) > { > >> static unsigned ext_csd_bits[][2] = { > >> { EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 > }, > >> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c > >> index 6f27d35..a775131 100644 > >> --- a/drivers/mmc/core/sd.c > >> +++ b/drivers/mmc/core/sd.c > >> @@ -661,7 +661,8 @@ static int mmc_sd_init_uhs_card(struct mmc_card > >> *card) > >> > >> /* SPI mode doesn't define CMD19 */ > >> if (!mmc_host_is_spi(card->host) && card->host->ops- > >> >execute_tuning) > >> - err = card->host->ops->execute_tuning(card->host); > >> + err = card->host->ops->execute_tuning(card->host, > \ > >> + > > MMC_SEND_TUNING_BLOCK); > >> > >> out: > >> kfree(status); > >> diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c > >> index b77f770..bd7bacc 100644 > >> --- a/drivers/mmc/core/sdio.c > >> +++ b/drivers/mmc/core/sdio.c > >> @@ -14,6 +14,7 @@ > >> > >> #include <linux/mmc/host.h> > >> #include <linux/mmc/card.h> > >> +#include <linux/mmc/mmc.h> > >> #include <linux/mmc/sdio.h> > >> #include <linux/mmc/sdio_func.h> > >> #include <linux/mmc/sdio_ids.h> > >> @@ -556,7 +557,8 @@ static int mmc_sdio_init_uhs_card(struct > mmc_card > >> *card) > >> > >> /* Initialize and start re-tuning timer */ > >> if (!mmc_host_is_spi(card->host) && card->host->ops- > >> >execute_tuning) > >> - err = card->host->ops->execute_tuning(card->host); > >> + err = card->host->ops->execute_tuning(card->host, > >> + > > MMC_SEND_TUNING_BLOCK); > >> > >> out: > >> > >> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h > >> index 9478a6b..9f22ba5 100644 > >> --- a/include/linux/mmc/card.h > >> +++ b/include/linux/mmc/card.h > >> @@ -216,6 +216,7 @@ struct mmc_card { > >> #define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in > ultra > >> high speed mode */ > >> #define MMC_CARD_SDXC (1<<6) /* card is > SDXC */ > >> #define MMC_CARD_REMOVED (1<<7) /* card has been > >> removed */ > >> +#define MMC_STATE_HIGHSPEED_200 (1<<8) /* card is in > >> HS200 mode */ > >> unsigned int quirks; /* card quirks */ > >> #define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO > FN0 > >> writes outside of the VS CCCR range */ > >> #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func- > >> >cur_blksize */ > >> @@ -374,6 +375,7 @@ static inline void __maybe_unused > >> remove_quirk(struct mmc_card *card, int data) > >> #define mmc_card_present(c) ((c)->state & MMC_STATE_PRESENT) > >> #define mmc_card_readonly(c) ((c)->state & MMC_STATE_READONLY) > >> #define mmc_card_highspeed(c) ((c)->state & > MMC_STATE_HIGHSPEED) > >> +#define mmc_card_hs200(c) ((c)->state & MMC_STATE_HIGHSPEED_200) > >> #define mmc_card_blockaddr(c) ((c)->state & > MMC_STATE_BLOCKADDR) > >> #define mmc_card_ddr_mode(c) ((c)->state & MMC_STATE_HIGHSPEED_DDR) > >> #define mmc_card_uhs(c) ((c)->state & > >> MMC_STATE_ULTRAHIGHSPEED) > >> @@ -384,6 +386,7 @@ static inline void __maybe_unused > >> remove_quirk(struct mmc_card *card, int data) > >> #define mmc_card_set_present(c) ((c)->state |= > MMC_STATE_PRESENT) > >> #define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY) > >> #define mmc_card_set_highspeed(c) ((c)->state |= > MMC_STATE_HIGHSPEED) > >> +#define mmc_card_set_hs200(c) ((c)->state |= > >> MMC_STATE_HIGHSPEED_200) > >> #define mmc_card_set_blockaddr(c) ((c)->state |= > MMC_STATE_BLOCKADDR) > >> #define mmc_card_set_ddr_mode(c) ((c)->state |= > >> MMC_STATE_HIGHSPEED_DDR) > >> #define mmc_card_set_uhs(c) ((c)->state |= > MMC_STATE_ULTRAHIGHSPEED) > >> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h > >> index 665548e..2c8cc69 100644 > >> --- a/include/linux/mmc/mmc.h > >> +++ b/include/linux/mmc/mmc.h > >> @@ -51,6 +51,7 @@ > >> #define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 > >> */ > >> #define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 > >> */ > >> #define MMC_SEND_TUNING_BLOCK 19 /* adtc R1 > >> */ > >> +#define MMC_SEND_TUNING_BLOCK_HS200 21 /* adtc R1 */ > >> > >> /* class 3 */ > >> #define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 > >> */ > >> @@ -339,13 +340,76 @@ struct _mmc_csd { > >> > >> #define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */ > >> #define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */ > >> -#define EXT_CSD_CARD_TYPE_MASK 0xF /* Mask out reserved > bits */ > >> +#define EXT_CSD_CARD_TYPE_MASK 0x3F /* Mask out reserved > bits */ > >> #define EXT_CSD_CARD_TYPE_DDR_1_8V (1<<2) /* Card can run at > 52MHz > >> */ > >> /* DDR mode @1.8V or 3V > I/O */ > >> #define EXT_CSD_CARD_TYPE_DDR_1_2V (1<<3) /* Card can run at > 52MHz > >> */ > >> /* DDR mode @1.2V I/O */ > >> #define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V > \ > >> | EXT_CSD_CARD_TYPE_DDR_1_2V) > >> +#define EXT_CSD_CARD_TYPE_SDR_1_8V (1<<4) /* Card can run at > >> 200MHz */ > >> +#define EXT_CSD_CARD_TYPE_SDR_1_2V (1<<5) /* Card can run at > >> 200MHz */ > >> + /* SDR mode @1.2V I/O > */ > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V > \ > >> + | EXT_CSD_CARD_TYPE_SDR_1_2V) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_ALL (EXT_CSD_CARD_TYPE_SDR_200 > \ > >> + | EXT_CSD_CARD_TYPE_52 > \ > >> + | EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_ALL > >> (EXT_CSD_CARD_TYPE_SDR_1_2V \ > >> + | EXT_CSD_CARD_TYPE_52 > \ > >> + | EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_ALL > >> (EXT_CSD_CARD_TYPE_SDR_1_8V \ > >> + | EXT_CSD_CARD_TYPE_52 > \ > >> + | EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V > >> (EXT_CSD_CARD_TYPE_SDR_1_2V \ > >> + | > EXT_CSD_CARD_TYPE_DDR_1_8V > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V > >> (EXT_CSD_CARD_TYPE_SDR_1_8V \ > >> + | > EXT_CSD_CARD_TYPE_DDR_1_8V > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V > >> (EXT_CSD_CARD_TYPE_SDR_1_2V \ > >> + | > EXT_CSD_CARD_TYPE_DDR_1_2V > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V > >> (EXT_CSD_CARD_TYPE_SDR_1_8V \ > >> + | > EXT_CSD_CARD_TYPE_DDR_1_2V > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52 > >> (EXT_CSD_CARD_TYPE_SDR_1_2V \ > >> + | > EXT_CSD_CARD_TYPE_DDR_52 > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52 > >> (EXT_CSD_CARD_TYPE_SDR_1_8V \ > >> + | > EXT_CSD_CARD_TYPE_DDR_52 > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V > >> (EXT_CSD_CARD_TYPE_SDR_200 \ > >> + | > EXT_CSD_CARD_TYPE_DDR_1_8V > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V > >> (EXT_CSD_CARD_TYPE_SDR_200 \ > >> + | > EXT_CSD_CARD_TYPE_DDR_1_2V > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> + > >> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52 > (EXT_CSD_CARD_TYPE_SDR_200 > >> \ > >> + | > EXT_CSD_CARD_TYPE_DDR_52 > > \ > >> + | EXT_CSD_CARD_TYPE_52 > > \ > >> + | > EXT_CSD_CARD_TYPE_26) > >> > >> #define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */ > >> #define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */ > >> -- > >> 1.7.1 > >> > >> -- > >> To unsubscribe from this list: send the line "unsubscribe linux-mmc" > in > >> the body of a message to majordomo@xxxxxxxxxxxxxxx > >> More majordomo info at http://vger.kernel.org/majordomo-info.html > > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
