Hi Girish, > -----Original Message----- > From: Girish K S [mailto:girish.shivananjappa@xxxxxxxxxx] > Sent: Monday, November 21, 2011 4:12 PM > To: Subhash Jadavani > Cc: linux-mmc@xxxxxxxxxxxxxxx; cjb@xxxxxxxxxx; patches@xxxxxxxxxx; > linux-samsung-soc@xxxxxxxxxxxxxxx > Subject: Re: [PATCH RESEND V4] mmc: core: HS200 mode support for eMMC > 4.5 > > On 19 November 2011 00:29, Subhash Jadavani <subhashj@xxxxxxxxxxxxxx> > wrote: > > Hi Girish, > > > >> -----Original Message----- > >> From: linux-mmc-owner@xxxxxxxxxxxxxxx [mailto:linux-mmc- > >> owner@xxxxxxxxxxxxxxx] On Behalf Of Girish K S > >> Sent: Wednesday, October 26, 2011 10:30 AM > >> To: linux-mmc@xxxxxxxxxxxxxxx > >> Cc: cjb@xxxxxxxxxx; patches@xxxxxxxxxx; linux-samsung- > >> soc@xxxxxxxxxxxxxxx; Girish K S > >> Subject: [PATCH RESEND V4] mmc: core: HS200 mode support for eMMC > 4.5 > >> > >> This patch adds the support of the HS200 bus speed for eMMC 4.5 > >> devices. > >> The eMMC 4.5 devices have support for 200MHz bus speed.The mmc core > and > >> host modules have been touched to add support for this module. > >> > >> It is necessary to know the card type in the sdhci.c file to add > >> support > >> for eMMC tuning function. So card.h file is included to import the > card > >> data structure. > > > > We don't need to know the card type in the host controller driver if > we pass > > the command opcode as the 2nd argument to execute_tuning() ops. > Command > > opcode can have have either CMD19 or CMD21 as it's value depending on > the > > card type (whether it's SD3.0 card or eMMC4.5 card). Can you see if we can implement this? > > > > > >> > >> cc: Chris Ball <cjb@xxxxxxxxxx> > >> Signed-off-by: Girish K S <girish.shivananjappa@xxxxxxxxxx> > >> --- > >> Changes in v4: > >> Rebased onto chris-mmc/mmc-next branch. This patch is > >> successfully > >> applied on commit with id > >> de022ed3fdc14808299b2fa66dbb1ed5ab921912. > >> Changes in v3: > >> In the previous commits of chris-mmc/mmc-next branch, the > patch > >> with > >> commit id (c0f22a2c92e357e7cb3988b0b13034d70b7461f9) defines > >> caps2 for > >> more capabilities. This patch version deletes the member > >> ext_caps(created > >> in my earlier patch) from struct mmc_host and reuses already > >> accepted > >> caps2 member. > >> Changes in v2: > >> Rebased to latest chris-mmc/mmc-next branch. Resolved > indentation > >> problems identified in review. This patch has to be applied > >> before > >> the patch released for modifying the printk messages. > >> Changes in v1: > >> Case statements in switch that produce same result have > >> been combined to reduce repeated assignments. > >> patch recreated after rebase to chris balls mmc-next branch. > >> > >> drivers/mmc/core/bus.c | 3 +- > >> drivers/mmc/core/mmc.c | 92 > >> ++++++++++++++++++++++++++++++++++++++++---- > >> drivers/mmc/host/sdhci.c | 36 +++++++++++++++--- > >> include/linux/mmc/card.h | 3 + > >> include/linux/mmc/host.h | 6 +++ > >> include/linux/mmc/mmc.h | 8 +++- > >> include/linux/mmc/sdhci.h | 1 + > >> 7 files changed, 132 insertions(+), 17 deletions(-) > >> > >> diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c > >> index 46b6e84..2f82f6b 100644 > >> --- a/drivers/mmc/core/bus.c > >> +++ b/drivers/mmc/core/bus.c > >> @@ -301,10 +301,11 @@ int mmc_add_card(struct mmc_card *card) > >> mmc_card_ddr_mode(card) ? "DDR " : "", > >> type); > >> } else { > >> - printk(KERN_INFO "%s: new %s%s%s card at address > %04x\n", > >> + pr_info("%s: new %s%s%s%s card at address %04x\n", > >> mmc_hostname(card->host), > >> mmc_sd_card_uhs(card) ? "ultra high speed " : > >> (mmc_card_highspeed(card) ? "high speed " : > ""), > >> + (mmc_card_hs200(card) ? "HS200 " : ""), > >> mmc_card_ddr_mode(card) ? "DDR " : "", > >> type, card->rca); > >> } > >> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c > >> index 3627044..4db248c 100644 > >> --- a/drivers/mmc/core/mmc.c > >> +++ b/drivers/mmc/core/mmc.c > >> @@ -285,6 +285,39 @@ static int mmc_read_ext_csd(struct mmc_card > *card, > >> u8 *ext_csd) > >> } > >> card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE]; > >> switch (ext_csd[EXT_CSD_CARD_TYPE] & EXT_CSD_CARD_TYPE_MASK) { > >> + case EXT_CSD_CARD_TYPE_SDR_200 | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_200 | EXT_CSD_CARD_TYPE_DDR_1_8V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_200 | EXT_CSD_CARD_TYPE_DDR_1_2V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_200 | EXT_CSD_CARD_TYPE_DDR_52 | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + card->ext_csd.hs_max_dtr = 200000000; > >> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_200; > >> + break; > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V | EXT_CSD_CARD_TYPE_DDR_1_8V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V | EXT_CSD_CARD_TYPE_DDR_1_2V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_1_2V | EXT_CSD_CARD_TYPE_DDR_52 | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + card->ext_csd.hs_max_dtr = 200000000; > >> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V; > >> + break; > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V | EXT_CSD_CARD_TYPE_DDR_1_8V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V | EXT_CSD_CARD_TYPE_DDR_1_2V | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + case EXT_CSD_CARD_TYPE_SDR_1_8V | EXT_CSD_CARD_TYPE_DDR_52 | > >> + EXT_CSD_CARD_TYPE_52 | EXT_CSD_CARD_TYPE_26: > >> + card->ext_csd.hs_max_dtr = 200000000; > >> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_8V; > >> + break; > > > > Can't we optimize this? This looks like too many case statements. > > > > Basically we can have checks like this: > > > > temp = ext_csd[EXT_CSD_CARD_TYPE] & EXT_CSD_CARD_TYPE_MASK; > > if ((temp & EXT_CSD_CARD_TYPE_SDR_1_2V == EXT_CSD_CARD_TYPE_SDR_1_2V) > || > > (temp & EXT_CSD_CARD_TYPE_SDR_1_8V == > EXT_CSD_CARD_TYPE_SDR_1_8V)) { > > card->ext_csd.hs_max_dtr = 200000000; > > card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V; /* we > can have > > some logic to identify the card type correctly */ > > } Can you please respond to this? > > > > > >> case EXT_CSD_CARD_TYPE_DDR_52 | EXT_CSD_CARD_TYPE_52 | > >> EXT_CSD_CARD_TYPE_26: > >> card->ext_csd.hs_max_dtr = 52000000; > >> @@ -699,6 +732,7 @@ static int mmc_init_card(struct mmc_host *host, > u32 > >> ocr, > >> { > >> struct mmc_card *card; > >> int err, ddr = 0; > >> + int hs_sdr = 0; > >> u32 cid[4]; > >> unsigned int max_dtr; > >> u32 rocr; > >> @@ -890,11 +924,15 @@ static int mmc_init_card(struct mmc_host > *host, > >> u32 ocr, > >> /* > >> * Activate high speed (if supported) > >> */ > >> - if ((card->ext_csd.hs_max_dtr != 0) && > >> - (host->caps & MMC_CAP_MMC_HIGHSPEED)) { > >> - err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> - EXT_CSD_HS_TIMING, 1, > >> - card->ext_csd.generic_cmd6_time); > >> + if (card->ext_csd.hs_max_dtr != 0) { > > > > We should enter into this if condition only if one of the this cap > > (MMC_CAP2_HIGHSPEED_200 or MMC_CAP_MMC_HIGHSPEED) is set. > card->ext_csd.hs_max_dtr is non zero for high speed only i.e for > frequency above 26Mhz. For anything less than 26 Mhz this if > condition is skipped. I guess that's not the correct assumption here. Even for EXT_CSD_CARD_TYPE_26 card type we have non zero value hs_max_dtr. Please check. case EXT_CSD_CARD_TYPE_26: card->ext_csd.hs_max_dtr = 26000000; > So its just enough if we check for less than 52 MHz and >= 52 Mhz. > > > >> + if ((card->ext_csd.hs_max_dtr > 52000000) && > >> + (host->caps2 & MMC_CAP2_HIGHSPEED_200)) > >> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> + EXT_CSD_HS_TIMING, 2, 0); > >> + else if (host->caps & MMC_CAP_MMC_HIGHSPEED) > >> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > >> + EXT_CSD_HS_TIMING, 1, 0); > >> + > >> if (err && err != -EBADMSG) > >> goto free_card; > >> > >> @@ -903,7 +941,10 @@ static int mmc_init_card(struct mmc_host *host, > >> u32 ocr, > >> mmc_hostname(card->host)); > >> err = 0; > >> } else { > >> - mmc_card_set_highspeed(card); > >> + if (card->ext_csd.hs_max_dtr > 52000000) > > > > I think there should be AND condition with (host->caps2 & > > MMC_CAP2_HIGHSPEED_200) for setting the card as HS200. > Ok will add it. > > > >> + mmc_card_set_hs200(card); > >> + else > >> + mmc_card_set_highspeed(card); > >> mmc_set_timing(card->host, MMC_TIMING_MMC_HS); > > > > As mentioned earlier, there should be new timing mode defined for > HS200. > can you share Host controller specification will check it. Our Qualcomm MSM SDCC host controller is not compliant to SDHCI (Standard Host controller interface) specification so our host controller implementation won't be same as controllers compliant to SDHCI. It's not just Qualcomm SDCC controller, there are many other SDCC controller (like mmci) which are not compliant to SDHCI standard. If you check the SD3.0 implementation (sd_set_bus_speed_mode() function in drivers/mmc/core/sd.c), core layer is setting the different timing modes for all the different UHS-I bus speed modes (like SDR104, SDR50, DDR50 etc ...). Then it's upto the host controller driver to see whether they want to make use this timing mode or not? Our host controller driver does make use of it for SD3.0 timing modes and similar we need to know HS200 timing mode in order to program our controller properly. > > > >> } > >> } > >> @@ -929,7 +970,7 @@ static int mmc_init_card(struct mmc_host *host, > u32 > >> ocr, > >> */ > >> max_dtr = (unsigned int)-1; > >> > >> - if (mmc_card_highspeed(card)) { > >> + if (mmc_card_highspeed(card) || mmc_card_hs200(card)) { > >> if (max_dtr > card->ext_csd.hs_max_dtr) > >> max_dtr = card->ext_csd.hs_max_dtr; > >> } else if (max_dtr > card->csd.max_dtr) { > >> @@ -955,6 +996,22 @@ static int mmc_init_card(struct mmc_host *host, > >> u32 ocr, > >> } > >> > >> /* > >> + * Indicate HS200 SDR mode (if supported). > >> + */ > >> + if (mmc_card_hs200(card)) { > >> + if ((card->ext_csd.card_type & > EXT_CSD_CARD_TYPE_SDR_1_8V) > >> + && ((host->caps2 & (MMC_CAP2_HS200_1_8V_SDR | > >> + MMC_CAP2_HS200)) > >> + == (MMC_CAP2_HS200_1_8V_SDR | > > MMC_CAP2_HS200))) > >> + hs_sdr = MMC_1_8V_SDR_MODE; > >> + else if ((card->ext_csd.card_type & > >> EXT_CSD_CARD_TYPE_SDR_1_2V) > >> + && ((host->caps2 & (MMC_CAP2_HS200_1_2V_SDR | > >> + MMC_CAP2_HS200)) > >> + == (MMC_CAP2_HS200_1_2V_SDR | > > MMC_CAP2_HS200))) > >> + hs_sdr = MMC_1_2V_SDR_MODE; > >> + } > >> + > >> + /* > >> * Activate wide bus and DDR (if supported). > >> */ > >> if ((card->csd.mmca_vsn >= CSD_SPEC_VER_4) && > >> @@ -994,16 +1051,24 @@ static int mmc_init_card(struct mmc_host > *host, > >> u32 ocr, > >> if (!err) { > >> mmc_set_bus_width(card->host, > bus_width); > >> > >> + if ((host->caps2 & MMC_CAP2_HS200) && > >> + card->host->ops->execute_tuning) > >> + err = card->host->ops-> \ > >> + execute_tuning(card- > >host); > > > > execute_tuning() should be executed immediately after the TIMING is > changed > > to HS200 and clock speed is changed to 200MHz. But here timing mode > and > > clock rate is changed and then you are also sending bus width change > > command. As host controller timing tuning has not completed, this bus > width > > change command may fail with CMD/DATA CRC errors. > > pls check the eMMC specification section 6.6.4 it says > "Note that the host should switch to the required bus width before > starting the tuning operation to > allow the tuning sequence to be done using the proper bus operating > conditions. Agreed. But specification doesn't when exactly the bus width change should happen. Right before Step.6 (mentioned in section 6.6.4) or before setting the HS200 mode in HS_TIMING and changing the clock speed. I would say we should set the bus width before the step.1 (mentioned in section 6.6.4). then proceed to execute all the step.1 and step.6 in sequence. As I had mentioned earlier, let's say at first you set the HS_TIMING=HS200 and set the clock speed to 200MHz. Now if you try to set the bus width (by sending the CMD6 and then reading the STATUS via CMD13) without executing tuning, CMD6/CMD13 may fail with CMD/RESPONSE CRC errors as controller sampling point is still not tuned. We had exact similar issue faced with SD3.0 as well on our host controller. You can take a look at this patch: http://www.spinics.net/lists/linux-arm-msm/msg03867.html > " > > So basically this should be the sequence. > > 1. set the bus width depending on the host controller and card > capability > > 2. If card support HS200 timing, change the timing of the card by > sending > > SWITCH command. Change the clock rate. Change the timing mode of > controller. > > 3. Now call the host controller execute_tuning ops to perform the > controller > > sampling point tuning. > > > > Also, let's pass the command opcode as the 2nd argument of the > > execute_tuning() function. Which means host controller driver need > not to > > know the card type. > > > >> + > >> /* > >> * If controller can't handle bus > width > > test, > >> * compare ext_csd previously read in > 1 bit > >> mode > >> * against ext_csd at new bus width > >> */ > >> - if (!(host->caps & > MMC_CAP_BUS_WIDTH_TEST)) > >> + if (!(host->caps & > MMC_CAP_BUS_WIDTH_TEST) > > && > >> + !err) > >> err = > mmc_compare_ext_csds(card, > >> bus_width); > >> - else > >> + else if (!err) > >> err = mmc_bus_test(card, > bus_width); > >> + else > >> + pr_warning("tuning execution > > failed\n"); > >> if (!err) > >> break; > >> } > >> @@ -1052,6 +1117,15 @@ static int mmc_init_card(struct mmc_host > *host, > >> u32 ocr, > >> mmc_card_set_ddr_mode(card); > >> mmc_set_timing(card->host, > MMC_TIMING_UHS_DDR50); > >> mmc_set_bus_width(card->host, bus_width); > >> + } else if (hs_sdr) { > >> + if (hs_sdr == EXT_CSD_CARD_TYPE_SDR_1_2V) { > >> + err = mmc_set_signal_voltage(host, > >> + MMC_SIGNAL_VOLTAGE_120, 0); > >> + if (err) > >> + goto err; > >> + } > >> + mmc_set_timing(card->host, MMC_TIMING_MMC_HS); > >> + mmc_set_bus_width(card->host, bus_width); > >> } > >> } > >> > >> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c > >> index a69d269..28fb747 100644 > >> --- a/drivers/mmc/host/sdhci.c > >> +++ b/drivers/mmc/host/sdhci.c > >> @@ -27,6 +27,7 @@ > >> > >> #include <linux/mmc/mmc.h> > >> #include <linux/mmc/host.h> > >> +#include <linux/mmc/card.h> > >> > >> #include "sdhci.h" > >> > >> @@ -1016,7 +1017,8 @@ static void sdhci_send_command(struct > sdhci_host > >> *host, struct mmc_command *cmd) > >> flags |= SDHCI_CMD_INDEX; > >> > >> /* CMD19 is special in that the Data Present Select should be > set > >> */ > >> - if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK)) > >> + if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK) || > >> + (cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200)) > >> flags |= SDHCI_CMD_DATA; > >> > >> sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), > >> SDHCI_COMMAND); > >> @@ -1684,10 +1686,13 @@ static int sdhci_execute_tuning(struct > mmc_host > >> *mmc) > >> * Host Controller needs tuning only in case of SDR104 mode > >> * and for SDR50 mode when Use Tuning for SDR50 is set in > >> * Capabilities register. > >> + * If the Host Controller supports the HS200 mode then tuning > >> + * function has to be executed. > >> */ > >> if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR104) || > >> (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR50) && > >> - (host->flags & SDHCI_SDR50_NEEDS_TUNING))) > >> + (host->flags & SDHCI_SDR50_NEEDS_TUNING)) || > >> + (host->flags & SDHCI_HS200_NEEDS_TUNING)) > >> ctrl |= SDHCI_CTRL_EXEC_TUNING; > >> else { > >> spin_unlock(&host->lock); > >> @@ -1723,7 +1728,10 @@ static int sdhci_execute_tuning(struct > mmc_host > >> *mmc) > >> if (!tuning_loop_counter && !timeout) > >> break; > >> > >> - cmd.opcode = MMC_SEND_TUNING_BLOCK; > >> + if (mmc->card->type == MMC_TYPE_MMC) > >> + cmd.opcode = MMC_SEND_TUNING_BLOCK_HS200; > >> + else > >> + cmd.opcode = MMC_SEND_TUNING_BLOCK; > >> cmd.arg = 0; > >> cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC; > >> cmd.retries = 0; > >> @@ -1738,7 +1746,17 @@ static int sdhci_execute_tuning(struct > mmc_host > >> *mmc) > >> * block to the Host Controller. So we set the block > size > >> * to 64 here. > >> */ > >> - sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64), > >> SDHCI_BLOCK_SIZE); > >> + if (mmc->card->type == MMC_TYPE_MMC) { > >> + if (mmc->ios.bus_width == MMC_BUS_WIDTH_8) > >> + sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, > 128), > >> + SDHCI_BLOCK_SIZE); > >> + else if (mmc->ios.bus_width == > MMC_BUS_WIDTH_4) > >> + sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, > 64), > >> + SDHCI_BLOCK_SIZE); > >> + } else { > >> + sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64), > >> + SDHCI_BLOCK_SIZE); > >> + } > >> > >> /* > >> * The tuning block is sent by the card to the host > >> controller. > >> @@ -2121,12 +2139,14 @@ static void sdhci_show_adma_error(struct > >> sdhci_host *host) { } > >> > >> static void sdhci_data_irq(struct sdhci_host *host, u32 intmask) > >> { > >> + u32 command; > >> BUG_ON(intmask == 0); > >> > >> /* CMD19 generates _only_ Buffer Read Ready interrupt */ > >> if (intmask & SDHCI_INT_DATA_AVAIL) { > >> - if (SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND)) == > >> - MMC_SEND_TUNING_BLOCK) { > >> + command = SDHCI_GET_CMD(sdhci_readw(host, > SDHCI_COMMAND)); > >> + if ((command == MMC_SEND_TUNING_BLOCK) || > >> + (command == MMC_SEND_TUNING_BLOCK_HS200)) { > >> host->tuning_done = 1; > >> wake_up(&host->buf_ready_int); > >> return; > >> @@ -2731,6 +2751,10 @@ int sdhci_add_host(struct sdhci_host *host) > >> if (caps[1] & SDHCI_USE_SDR50_TUNING) > >> host->flags |= SDHCI_SDR50_NEEDS_TUNING; > >> > >> + /* Does the host needs tuning for HS200? */ > >> + if (mmc->caps2 & MMC_CAP2_HS200) > >> + host->flags |= SDHCI_HS200_NEEDS_TUNING; > >> + > >> /* Driver Type(s) (A, C, D) supported by the host */ > >> if (caps[1] & SDHCI_DRIVER_TYPE_A) > >> mmc->caps |= MMC_CAP_DRIVER_TYPE_A; > >> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h > >> index 6e04e10..90af438 100644 > >> --- a/include/linux/mmc/card.h > >> +++ b/include/linux/mmc/card.h > >> @@ -206,6 +206,7 @@ struct mmc_card { > >> #define MMC_STATE_HIGHSPEED_DDR (1<<4) /* card is in > high > >> speed mode */ > >> #define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in > ultra > >> high speed mode */ > >> #define MMC_CARD_SDXC (1<<6) /* card is > SDXC */ > >> +#define MMC_STATE_HIGHSPEED_200 (1<<7) /* card is in HS200 > >> mode */ > >> unsigned int quirks; /* card quirks */ > >> #define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO > FN0 > >> writes outside of the VS CCCR range */ > >> #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func- > >> >cur_blksize */ > >> @@ -361,6 +362,7 @@ static inline void __maybe_unused > >> remove_quirk(struct mmc_card *card, int data) > >> #define mmc_card_present(c) ((c)->state & MMC_STATE_PRESENT) > >> #define mmc_card_readonly(c) ((c)->state & MMC_STATE_READONLY) > >> #define mmc_card_highspeed(c) ((c)->state & > MMC_STATE_HIGHSPEED) > >> +#define mmc_card_hs200(c) ((c)->state & MMC_STATE_HIGHSPEED_200) > >> #define mmc_card_blockaddr(c) ((c)->state & > MMC_STATE_BLOCKADDR) > >> #define mmc_card_ddr_mode(c) ((c)->state & MMC_STATE_HIGHSPEED_DDR) > >> #define mmc_sd_card_uhs(c) ((c)->state & MMC_STATE_ULTRAHIGHSPEED) > >> @@ -369,6 +371,7 @@ static inline void __maybe_unused > >> remove_quirk(struct mmc_card *card, int data) > >> #define mmc_card_set_present(c) ((c)->state |= > MMC_STATE_PRESENT) > >> #define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY) > >> #define mmc_card_set_highspeed(c) ((c)->state |= > MMC_STATE_HIGHSPEED) > >> +#define mmc_card_set_hs200(c) ((c)->state |= > >> MMC_STATE_HIGHSPEED_200) > >> #define mmc_card_set_blockaddr(c) ((c)->state |= > MMC_STATE_BLOCKADDR) > >> #define mmc_card_set_ddr_mode(c) ((c)->state |= > >> MMC_STATE_HIGHSPEED_DDR) > >> #define mmc_sd_card_set_uhs(c) ((c)->state |= > >> MMC_STATE_ULTRAHIGHSPEED) > >> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h > >> index a3ac9c4..20551f5 100644 > >> --- a/include/linux/mmc/host.h > >> +++ b/include/linux/mmc/host.h > >> @@ -60,6 +60,8 @@ struct mmc_ios { > >> #define MMC_SDR_MODE 0 > >> #define MMC_1_2V_DDR_MODE 1 > >> #define MMC_1_8V_DDR_MODE 2 > >> +#define MMC_1_2V_SDR_MODE 3 > >> +#define MMC_1_8V_SDR_MODE 4 > >> > >> unsigned char signal_voltage; /* signalling voltage > >> (1.8V or 3.3V) */ > >> > >> @@ -242,6 +244,10 @@ struct mmc_host { > >> #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control > */ > >> #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff > >> supported */ > >> #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock > reads > >> don't work */ > >> +#define MMC_CAP2_HS200 (1 << 4) /* Host > supports > > HS200 mode > >> */ > > > > Why is this cap required? You have already defined this 2 caps > > MMC_CAP2_HS200_1_8V_SDR & MMC_CAP2_HS200_1_2V_SDR which should be > enough. > > > >> +#define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support > */ > >> +#define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support > */ > >> +#define MMC_CAP2_HIGHSPEED_200 (1 << 7) /* Can do MMC > HS200 > > Why is this is this cap required? > > will remove it Both MMC_CAP2_HIGHSPEED_200 and MMC_CAP2_HS200 are redundant. > >> timing */ > >> > >> mmc_pm_flag_t pm_caps; /* supported pm > features */ > >> unsigned int power_notify_type; > >> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h > >> index 0e71356..af4fa72 100644 > >> --- a/include/linux/mmc/mmc.h > >> +++ b/include/linux/mmc/mmc.h > >> @@ -51,6 +51,7 @@ > >> #define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 > >> */ > >> #define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 > >> */ > >> #define MMC_SEND_TUNING_BLOCK 19 /* adtc R1 > >> */ > >> +#define MMC_SEND_TUNING_BLOCK_HS200 21 /* adtc R1 */ > >> > >> /* class 3 */ > >> #define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 > >> */ > >> @@ -333,13 +334,18 @@ struct _mmc_csd { > >> > >> #define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */ > >> #define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */ > >> -#define EXT_CSD_CARD_TYPE_MASK 0xF /* Mask out reserved > bits */ > >> +#define EXT_CSD_CARD_TYPE_MASK 0x3F /* Mask out reserved > bits */ > >> #define EXT_CSD_CARD_TYPE_DDR_1_8V (1<<2) /* Card can run at > 52MHz > >> */ > >> /* DDR mode @1.8V or 3V > I/O */ > >> #define EXT_CSD_CARD_TYPE_DDR_1_2V (1<<3) /* Card can run at > 52MHz > >> */ > >> /* DDR mode @1.2V I/O */ > >> #define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V > \ > >> | EXT_CSD_CARD_TYPE_DDR_1_2V) > >> +#define EXT_CSD_CARD_TYPE_SDR_1_8V (1<<4) /* Card can run at > >> 200MHz */ > >> +#define EXT_CSD_CARD_TYPE_SDR_1_2V (1<<5) /* Card can run at > >> 200MHz */ > >> + /* SDR mode @1.2V I/O > */ > >> +#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V > \ > >> + | EXT_CSD_CARD_TYPE_SDR_1_2V) > >> > >> #define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */ > >> #define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */ > >> diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h > >> index e4b6935..d9a2222 100644 > >> --- a/include/linux/mmc/sdhci.h > >> +++ b/include/linux/mmc/sdhci.h > >> @@ -121,6 +121,7 @@ struct sdhci_host { > >> #define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */ > >> #define SDHCI_PV_ENABLED (1<<8) /* Preset value enabled */ > >> #define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */ > >> +#define SDHCI_HS200_NEEDS_TUNING (1<<10) /* HS200 needs tuning > */ > >> > >> unsigned int version; /* SDHCI spec. version */ > >> > >> -- > >> 1.7.1 > >> > >> -- > >> To unsubscribe from this list: send the line "unsubscribe linux-mmc" > in > >> the body of a message to majordomo@xxxxxxxxxxxxxxx > >> More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
