SDHCI driver for PXAV3 SoCs, such as MMP2, the driver based on sdhci-pltfm to handle resource etc.
Signed-off-by: Zhangfei Gao <zhangfei.gao@xxxxxxxxxxx>
Signed-off-by: Philip Rakity <prakity@xxxxxxxxxxx>
---
arch/arm/plat-pxa/include/plat/sdhci.h | 35 ++++-
drivers/mmc/host/Kconfig | 12 ++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-pxav3.c | 289 ++++++++++++++++++++++++++++++++
4 files changed, 332 insertions(+), 5 deletions(-)
create mode 100644 drivers/mmc/host/sdhci-pxav3.c
diff --git a/arch/arm/plat-pxa/include/plat/sdhci.h b/arch/arm/plat-pxa/include/plat/sdhci.h
index 1ab332e..6873dc5 100644
--- a/arch/arm/plat-pxa/include/plat/sdhci.h
+++ b/arch/arm/plat-pxa/include/plat/sdhci.h
@@ -15,21 +15,46 @@
/* pxa specific flag */
/* Require clock free running */
-#define PXA_FLAG_DISABLE_CLOCK_GATING (1<<0)
-
+#define PXA_FLAG_ENABLE_CLOCK_GATING (1<<0)
+/* card alwayes wired to host, like on-chip emmc */
+#define PXA_FLAG_CARD_PERMANENT (1<<1)
/* Board design supports 8-bit data on SD/SDIO BUS */
#define PXA_FLAG_SD_8_BIT_CAPABLE_SLOT (1<<2)
/*
* struct pxa_sdhci_platdata() - Platform device data for PXA SDHCI
- * @max_speed: the maximum speed supported
- * @quirks: quirks of specific device
* @flags: flags for platform requirement
+ * @clk_delay_cycles:
+ * mmp2: each step is roughly 100ps, 5bits width
+ * pxa910: each step is 1ns, 4bits width
+ * @clk_delay_sel: select clk_delay, used on pxa910
+ * 0: choose feedback clk
+ * 1: choose feedback clk + delay value
+ * 2: choose internal clk
+ * @clk_delay_enable: enable clk_delay or not, used on pxa910
+ * @ext_cd_gpio: gpio pin used for external CD line
+ * @ext_cd_gpio_invert: invert values for external CD gpio line
+ * @max_speed: the maximum speed supported
+ * @host_caps: Standard MMC host capabilities bit field.
+ * @quirks: quirks of platfrom
+ * @pm_caps: pm_caps of platfrom
*/
struct sdhci_pxa_platdata {
+ unsigned int flags;
+ unsigned int clk_delay_cycles;
+ unsigned int clk_delay_sel;
+ bool clk_delay_enable;
+ unsigned int ext_cd_gpio;
+ bool ext_cd_gpio_invert;
unsigned int max_speed;
+ unsigned int host_caps;
unsigned int quirks;
- unsigned int flags;
+ unsigned int pm_caps;
+};
+
+struct sdhci_pxa {
+ u8 clk_enable;
+ u8 power_mode;
};
#endif /* __PLAT_PXA_SDHCI_H */
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 74e77c9..6525a04 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -193,6 +193,18 @@ config MMC_SDHCI_PXA
If unsure, say N.
+config MMC_SDHCI_PXAV3
+ tristate "Marvell MMP2 SD Host Controller support (PXAV3)"
+ select MMC_SDHCI
+ select MMC_SDHCI_PLTFM
+ default CPU_MMP2
+ help
+ This selects the Marvell(R) PXAV3 SD Host Controller.
+ If you have a MMP2 platform with SD Host Controller
+ and a card slot, say Y or M here.
+
+ If unsure, say N.
+
config MMC_SDHCI_SPEAR
tristate "SDHCI support on ST SPEAr platform"
depends on MMC_SDHCI && PLAT_SPEAR
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index bf479ab..688cc52 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
obj-$(CONFIG_MMC_SDHCI) += sdhci.o
obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
obj-$(CONFIG_MMC_SDHCI_PXA) += sdhci-pxa.o
+obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
obj-$(CONFIG_MMC_WBSD) += wbsd.o
diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c
new file mode 100644
index 0000000..901f00f
--- /dev/null
+++ b/drivers/mmc/host/sdhci-pxav3.c
@@ -0,0 +1,289 @@
+/*
+ * Copyright (C) 2010 Marvell International Ltd.
+ * Zhangfei Gao <zhangfei.gao@xxxxxxxxxxx>
+ * Kevin Wang <dwang4@xxxxxxxxxxx>
+ * Mingwei Wang <mwwang@xxxxxxxxxxx>
+ * Philip Rakity <prakity@xxxxxxxxxxx>
+ * Mark Brown <markb@xxxxxxxxxxx>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+#include <plat/sdhci.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include "sdhci.h"
+#include "sdhci-pltfm.h"
+
+#define SD_CLOCK_BURST_SIZE_SETUP 0x10A
+#define SDCLK_SEL 0x100
+#define SDCLK_DELAY_SHIFT 9
+#define SDCLK_DELAY_MASK 0x1f
+
+#define SD_CFG_FIFO_PARAM 0x100
+#define SDCFG_GEN_PAD_CLK_ON (1<<6)
+#define SDCFG_GEN_PAD_CLK_CNT_MASK 0xFF
+#define SDCFG_GEN_PAD_CLK_CNT_SHIFT 24
+
+#define SD_SPI_MODE 0x108
+#define SD_CE_ATA_1 0x10C
+
+#define SD_CE_ATA_2 0x10E
+#define SDCE_MISC_INT (1<<2)
+#define SDCE_MISC_INT_EN (1<<1)
+
+static void pxav3_set_private_registers(struct sdhci_host *host, u8 mask)
+{
+ struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc));
+ struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
+
+ if (mask == SDHCI_RESET_ALL) {
+ /*
+ * tune timing of read data/command when crc error happen
+ * no performance impact
+ */
+ if (pdata && 0 != pdata->clk_delay_cycles) {
+ u16 tmp;
+
+ tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP);
+ tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK)
+ << SDCLK_DELAY_SHIFT;
+ tmp |= SDCLK_SEL;
+ writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP);
+ }
+ }
+}
+
+#define MAX_WAIT_COUNT 5
+static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
+ u16 tmp;
+ int count;
+
+ if (pxa->power_mode == MMC_POWER_UP
+ && power_mode == MMC_POWER_ON) {
+
+ dev_dbg(mmc_dev(host->mmc),
+ "%s: slot->power_mode = %d,"
+ "ios->power_mode = %d\n",
+ __func__,
+ pxa->power_mode,
+ power_mode);
+
+ /* set we want notice of when 74 clocks are sent */
+ tmp = readw(host->ioaddr + SD_CE_ATA_2);
+ tmp |= SDCE_MISC_INT_EN;
+ writew(tmp, host->ioaddr + SD_CE_ATA_2);
+
+ /* start sending the 74 clocks */
+ tmp = readw(host->ioaddr + SD_CFG_FIFO_PARAM);
+ tmp |= SDCFG_GEN_PAD_CLK_ON;
+ writew(tmp, host->ioaddr + SD_CFG_FIFO_PARAM);
+
+ /* slowest speed is about 100KHz or 10usec per clock */
+ udelay(740);
+ count = 0;
+
+ while (count++ < MAX_WAIT_COUNT) {
+ if ((readw(host->ioaddr + SD_CE_ATA_2)
+ & SDCE_MISC_INT) == 0)
+ break;
+ udelay(10);
+ }
+
+ if (count == MAX_WAIT_COUNT)
+ dev_warn(mmc_dev(host->mmc), "74 clock interrupt not cleared\n");
+
+ /* clear the interrupt bit if posted */
+ tmp = readw(host->ioaddr + SD_CE_ATA_2);
+ tmp |= SDCE_MISC_INT;
+ writew(tmp, host->ioaddr + SD_CE_ATA_2);
+ }
+ pxa->power_mode = power_mode;
+}
+
+static int pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
+{
+ u16 ctrl_2;
+
+ /*
+ * Set V18_EN -- UHS modes do not work without this.
+ * does not change signaling voltage
+ */
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+ /* Select Bus Speed Mode for host */
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ switch (uhs) {
+ case MMC_TIMING_UHS_SDR12:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
+ break;
+ case MMC_TIMING_UHS_SDR25:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
+ break;
+ case MMC_TIMING_UHS_SDR50:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR50 | SDHCI_CTRL_VDD_180;
+ break;
+ case MMC_TIMING_UHS_SDR104:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180;
+ break;
+ case MMC_TIMING_UHS_DDR50:
+ ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180;
+ break;
+ }
+
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+ dev_dbg(mmc_dev(host->mmc),
+ "%s uhs = %d, ctrl_2 = %04X\n",
+ __func__, uhs, ctrl_2);
+
+ return 0;
+}
+
+static struct sdhci_ops pxav3_sdhci_ops = {
+ .platform_reset_exit = pxav3_set_private_registers,
+ .set_uhs_signaling = pxav3_set_uhs_signaling,
+ .platform_send_init_74_clocks = pxav3_gen_init_74_clocks,
+};
+
+static int __devinit sdhci_pxav3_probe(struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct sdhci_host *host = NULL;
+ struct sdhci_pxa *pxa = NULL;
+ int ret;
+ struct clk *clk;
+
+ pxa = kzalloc(sizeof(struct sdhci_pxa), GFP_KERNEL);
+ if (!pxa)
+ return -ENOMEM;
+
+ host = sdhci_pltfm_init(pdev, NULL);
+ if (IS_ERR(host)) {
+ kfree(pxa);
+ return PTR_ERR(host);
+ }
+ pltfm_host = sdhci_priv(host);
+ pltfm_host->priv = pxa;
+
+ clk = clk_get(dev, "PXA-SDHCLK");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "failed to get io clock\n");
+ ret = PTR_ERR(clk);
+ goto err_clk_get;
+ }
+ pltfm_host->clk = clk;
+ clk_enable(clk);
+
+ host->quirks = SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
+ | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC;
+
+ /* enable 1/8V DDR capable */
+ host->mmc->caps |= MMC_CAP_1_8V_DDR;
+
+ if (pdata) {
+ if (pdata->flags & PXA_FLAG_CARD_PERMANENT) {
+ /* on-chip device */
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+ host->mmc->caps |= MMC_CAP_NONREMOVABLE;
+ }
+
+ /* If slot design supports 8 bit data, indicate this to MMC. */
+ if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT)
+ host->mmc->caps |= MMC_CAP_8_BIT_DATA;
+
+ if (pdata->quirks)
+ host->quirks |= pdata->quirks;
+ if (pdata->host_caps)
+ host->mmc->caps |= pdata->host_caps;
+ if (pdata->pm_caps)
+ host->mmc->pm_caps |= pdata->pm_caps;
+ }
+
+ host->ops = &pxav3_sdhci_ops;
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to add host\n");
+ goto err_add_host;
+ }
+
+ platform_set_drvdata(pdev, host);
+
+ return 0;
+
+err_add_host:
+ clk_disable(clk);
+ clk_put(clk);
+err_clk_get:
+ sdhci_pltfm_free(pdev);
+ kfree(pxa);
+ return ret;
+}
+
+static int __devexit sdhci_pxav3_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
+
+ sdhci_remove_host(host, 1);
+
+ clk_disable(pltfm_host->clk);
+ clk_put(pltfm_host->clk);
+ sdhci_pltfm_free(pdev);
+ kfree(pxa);
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver sdhci_pxav3_driver = {
+ .driver = {
+ .name = "sdhci-pxav3",
+ .owner = THIS_MODULE,
+ },
+ .probe = sdhci_pxav3_probe,
+ .remove = __devexit_p(sdhci_pxav3_remove),
+#ifdef CONFIG_PM
+ .suspend = sdhci_pltfm_suspend,
+ .resume = sdhci_pltfm_resume,
+#endif
+};
+static int __init sdhci_pxav3_init(void)
+{
+ return platform_driver_register(&sdhci_pxav3_driver);
+}
+
+static void __exit sdhci_pxav3_exit(void)
+{
+ platform_driver_unregister(&sdhci_pxav3_driver);
+}
+
+module_init(sdhci_pxav3_init);
+module_exit(sdhci_pxav3_exit);
+
+MODULE_DESCRIPTION("SDHCI driver for pxav3");
+MODULE_AUTHOR("Marvell International Ltd.");
+MODULE_LICENSE("GPL v2");
+
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
