Instead of sharing sdhci-pxa.c, use sdhci-pxav3.c for mmp2.
The original method is not easy to track, which is share sdhci-pxa.c among pxa serious, like pxa910, mmp2, etc,
and put the platfrom difference under arch/arm.
Signed-off-by: Zhangfei Gao <zhangfei.gao@xxxxxxxxxxx>
Signed-off-by: Philip Rakity <prakity@xxxxxxxxxxx>
---
arch/arm/plat-pxa/include/plat/sdhci.h | 37 ++++-
drivers/mmc/host/Kconfig | 11 +-
drivers/mmc/host/Makefile | 2 +-
drivers/mmc/host/sdhci-pxa.c | 303 -------------------------------
drivers/mmc/host/sdhci-pxav3.c | 305 ++++++++++++++++++++++++++++++++
5 files changed, 343 insertions(+), 315 deletions(-)
delete mode 100644 drivers/mmc/host/sdhci-pxa.c
create mode 100644 drivers/mmc/host/sdhci-pxav3.c
diff --git a/arch/arm/plat-pxa/include/plat/sdhci.h b/arch/arm/plat-pxa/include/plat/sdhci.h
index 1ab332e..b4acf5c 100644
--- a/arch/arm/plat-pxa/include/plat/sdhci.h
+++ b/arch/arm/plat-pxa/include/plat/sdhci.h
@@ -15,21 +15,48 @@
/* pxa specific flag */
/* Require clock free running */
-#define PXA_FLAG_DISABLE_CLOCK_GATING (1<<0)
-
+#define PXA_FLAG_ENABLE_CLOCK_GATING (1<<0)
+/* card alwayes wired to host, like on-chip emmc */
+#define PXA_FLAG_CARD_PERMANENT (1<<1)
/* Board design supports 8-bit data on SD/SDIO BUS */
#define PXA_FLAG_SD_8_BIT_CAPABLE_SLOT (1<<2)
+/* card not use wp, such as micro sd card */
+#define PXA_FLAG_CARD_NO_WP (1<<3)
/*
* struct pxa_sdhci_platdata() - Platform device data for PXA SDHCI
- * @max_speed: the maximum speed supported
- * @quirks: quirks of specific device
* @flags: flags for platform requirement
+ * @clk_delay_cycles:
+ * mmp2: each step is roughly 100ps, 5bits width
+ * pxa910: each step is 1ns, 4bits width
+ * @clk_delay_sel: select clk_delay, used on pxa910
+ * 0: choose feedback clk
+ * 1: choose feedback clk + delay value
+ * 2: choose internal clk
+ * @clk_delay_enable: enable clk_delay or not, used on pxa910
+ * @ext_cd_gpio: gpio pin used for external CD line
+ * @ext_cd_gpio_invert: invert values for external CD gpio line
+ * @max_speed: the maximum speed supported
+ * @host_caps: Standard MMC host capabilities bit field.
+ * @quirks: quirks of platfrom
+ * @pm_caps: pm_caps of platfrom
*/
struct sdhci_pxa_platdata {
+ unsigned int flags;
+ unsigned int clk_delay_cycles;
+ unsigned int clk_delay_sel;
+ bool clk_delay_enable;
+ unsigned int ext_cd_gpio;
+ bool ext_cd_gpio_invert;
unsigned int max_speed;
+ unsigned int host_caps;
unsigned int quirks;
- unsigned int flags;
+ unsigned int pm_caps;
+};
+
+struct sdhci_pxa {
+ u8 clk_enable;
+ u8 power_mode;
};
#endif /* __PLAT_PXA_SDHCI_H */
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 74e77c9..4ee869a 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -181,14 +181,13 @@ config MMC_SDHCI_S3C
If unsure, say N.
-config MMC_SDHCI_PXA
- tristate "Marvell PXA168/PXA910/MMP2 SD Host Controller support"
- depends on ARCH_PXA || ARCH_MMP
+config MMC_SDHCI_PXAV3
+ tristate "Marvell PXAV3 SD Host Controller support"
select MMC_SDHCI
- select MMC_SDHCI_IO_ACCESSORS
+ select MMC_SDHCI_PLTFM
help
- This selects the Marvell(R) PXA168/PXA910/MMP2 SD Host Controller.
- If you have a PXA168/PXA910/MMP2 platform with SD Host Controller
+ This selects the Marvell(R) PXAV3 SD Host Controller.
+ If you have a PXAV3 platform (such as mmp2) with SD Host Controller
and a card slot, say Y or M here.
If unsure, say N.
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index bf479ab..9131a27 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_MMC_MXC) += mxcmmc.o
obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
obj-$(CONFIG_MMC_SDHCI) += sdhci.o
obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
-obj-$(CONFIG_MMC_SDHCI_PXA) += sdhci-pxa.o
+obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
obj-$(CONFIG_MMC_WBSD) += wbsd.o
diff --git a/drivers/mmc/host/sdhci-pxa.c b/drivers/mmc/host/sdhci-pxa.c
deleted file mode 100644
index 089c9a6..0000000
--- a/drivers/mmc/host/sdhci-pxa.c
+++ /dev/null
@@ -1,303 +0,0 @@
-/* linux/drivers/mmc/host/sdhci-pxa.c
- *
- * Copyright (C) 2010 Marvell International Ltd.
- * Zhangfei Gao <zhangfei.gao@xxxxxxxxxxx>
- * Kevin Wang <dwang4@xxxxxxxxxxx>
- * Mingwei Wang <mwwang@xxxxxxxxxxx>
- * Philip Rakity <prakity@xxxxxxxxxxx>
- * Mark Brown <markb@xxxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/* Supports:
- * SDHCI support for MMP2/PXA910/PXA168
- *
- * Refer to sdhci-s3c.c.
- */
-
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/mmc/host.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/err.h>
-#include <plat/sdhci.h>
-#include "sdhci.h"
-
-#define DRIVER_NAME "sdhci-pxa"
-
-#define SD_FIFO_PARAM 0x104
-#define DIS_PAD_SD_CLK_GATE 0x400
-
-struct sdhci_pxa {
- struct sdhci_host *host;
- struct sdhci_pxa_platdata *pdata;
- struct clk *clk;
- struct resource *res;
-
- u8 clk_enable;
-};
-
-/*****************************************************************************\
- * *
- * SDHCI core callbacks *
- * *
-\*****************************************************************************/
-static void set_clock(struct sdhci_host *host, unsigned int clock)
-{
- struct sdhci_pxa *pxa = sdhci_priv(host);
- u32 tmp = 0;
-
- if (clock == 0) {
- if (pxa->clk_enable) {
- clk_disable(pxa->clk);
- pxa->clk_enable = 0;
- }
- } else {
- if (0 == pxa->clk_enable) {
- if (pxa->pdata->flags & PXA_FLAG_DISABLE_CLOCK_GATING) {
- tmp = readl(host->ioaddr + SD_FIFO_PARAM);
- tmp |= DIS_PAD_SD_CLK_GATE;
- writel(tmp, host->ioaddr + SD_FIFO_PARAM);
- }
- clk_enable(pxa->clk);
- pxa->clk_enable = 1;
- }
- }
-}
-
-static int set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
-{
- u16 ctrl_2;
-
- /*
- * Set V18_EN -- UHS modes do not work without this.
- * does not change signaling voltage
- */
- ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
-
- /* Select Bus Speed Mode for host */
- ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
- switch (uhs) {
- case MMC_TIMING_UHS_SDR12:
- ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
- break;
- case MMC_TIMING_UHS_SDR25:
- ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
- break;
- case MMC_TIMING_UHS_SDR50:
- ctrl_2 |= SDHCI_CTRL_UHS_SDR50 | SDHCI_CTRL_VDD_180;
- break;
- case MMC_TIMING_UHS_SDR104:
- ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180;
- break;
- case MMC_TIMING_UHS_DDR50:
- ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180;
- break;
- }
-
- sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
- pr_debug("%s:%s uhs = %d, ctrl_2 = %04X\n",
- __func__, mmc_hostname(host->mmc), uhs, ctrl_2);
-
- return 0;
-}
-
-static struct sdhci_ops sdhci_pxa_ops = {
- .set_uhs_signaling = set_uhs_signaling,
- .set_clock = set_clock,
-};
-
-/*****************************************************************************\
- * *
- * Device probing/removal *
- * *
-\*****************************************************************************/
-
-static int __devinit sdhci_pxa_probe(struct platform_device *pdev)
-{
- struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
- struct device *dev = &pdev->dev;
- struct sdhci_host *host = NULL;
- struct resource *iomem = NULL;
- struct sdhci_pxa *pxa = NULL;
- int ret, irq;
-
- irq = platform_get_irq(pdev, 0);
- if (irq < 0) {
- dev_err(dev, "no irq specified\n");
- return irq;
- }
-
- iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!iomem) {
- dev_err(dev, "no memory specified\n");
- return -ENOENT;
- }
-
- host = sdhci_alloc_host(&pdev->dev, sizeof(struct sdhci_pxa));
- if (IS_ERR(host)) {
- dev_err(dev, "failed to alloc host\n");
- return PTR_ERR(host);
- }
-
- pxa = sdhci_priv(host);
- pxa->host = host;
- pxa->pdata = pdata;
- pxa->clk_enable = 0;
-
- pxa->clk = clk_get(dev, "PXA-SDHCLK");
- if (IS_ERR(pxa->clk)) {
- dev_err(dev, "failed to get io clock\n");
- ret = PTR_ERR(pxa->clk);
- goto out;
- }
-
- pxa->res = request_mem_region(iomem->start, resource_size(iomem),
- mmc_hostname(host->mmc));
- if (!pxa->res) {
- dev_err(&pdev->dev, "cannot request region\n");
- ret = -EBUSY;
- goto out;
- }
-
- host->ioaddr = ioremap(iomem->start, resource_size(iomem));
- if (!host->ioaddr) {
- dev_err(&pdev->dev, "failed to remap registers\n");
- ret = -ENOMEM;
- goto out;
- }
-
- host->hw_name = "MMC";
- host->ops = &sdhci_pxa_ops;
- host->irq = irq;
- host->quirks = SDHCI_QUIRK_BROKEN_ADMA
- | SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
- | SDHCI_QUIRK_32BIT_DMA_ADDR
- | SDHCI_QUIRK_32BIT_DMA_SIZE
- | SDHCI_QUIRK_32BIT_ADMA_SIZE
- | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC;
-
- if (pdata->quirks)
- host->quirks |= pdata->quirks;
-
- /* enable 1/8V DDR capable */
- host->mmc->caps |= MMC_CAP_1_8V_DDR;
-
- /* If slot design supports 8 bit data, indicate this to MMC. */
- if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT)
- host->mmc->caps |= MMC_CAP_8_BIT_DATA;
-
- ret = sdhci_add_host(host);
- if (ret) {
- dev_err(&pdev->dev, "failed to add host\n");
- goto out;
- }
-
- if (pxa->pdata->max_speed)
- host->mmc->f_max = pxa->pdata->max_speed;
-
- platform_set_drvdata(pdev, host);
-
- return 0;
-out:
- if (host) {
- clk_put(pxa->clk);
- if (host->ioaddr)
- iounmap(host->ioaddr);
- if (pxa->res)
- release_mem_region(pxa->res->start,
- resource_size(pxa->res));
- sdhci_free_host(host);
- }
-
- return ret;
-}
-
-static int __devexit sdhci_pxa_remove(struct platform_device *pdev)
-{
- struct sdhci_host *host = platform_get_drvdata(pdev);
- struct sdhci_pxa *pxa = sdhci_priv(host);
- int dead = 0;
- u32 scratch;
-
- if (host) {
- scratch = readl(host->ioaddr + SDHCI_INT_STATUS);
- if (scratch == (u32)-1)
- dead = 1;
-
- sdhci_remove_host(host, dead);
-
- if (host->ioaddr)
- iounmap(host->ioaddr);
- if (pxa->res)
- release_mem_region(pxa->res->start,
- resource_size(pxa->res));
- if (pxa->clk_enable) {
- clk_disable(pxa->clk);
- pxa->clk_enable = 0;
- }
- clk_put(pxa->clk);
-
- sdhci_free_host(host);
- platform_set_drvdata(pdev, NULL);
- }
-
- return 0;
-}
-
-#ifdef CONFIG_PM
-static int sdhci_pxa_suspend(struct platform_device *dev, pm_message_t state)
-{
- struct sdhci_host *host = platform_get_drvdata(dev);
-
- return sdhci_suspend_host(host, state);
-}
-
-static int sdhci_pxa_resume(struct platform_device *dev)
-{
- struct sdhci_host *host = platform_get_drvdata(dev);
-
- return sdhci_resume_host(host);
-}
-#else
-#define sdhci_pxa_suspend NULL
-#define sdhci_pxa_resume NULL
-#endif
-
-static struct platform_driver sdhci_pxa_driver = {
- .probe = sdhci_pxa_probe,
- .remove = __devexit_p(sdhci_pxa_remove),
- .suspend = sdhci_pxa_suspend,
- .resume = sdhci_pxa_resume,
- .driver = {
- .name = DRIVER_NAME,
- .owner = THIS_MODULE,
- },
-};
-
-/*****************************************************************************\
- * *
- * Driver init/exit *
- * *
-\*****************************************************************************/
-
-static int __init sdhci_pxa_init(void)
-{
- return platform_driver_register(&sdhci_pxa_driver);
-}
-
-static void __exit sdhci_pxa_exit(void)
-{
- platform_driver_unregister(&sdhci_pxa_driver);
-}
-
-module_init(sdhci_pxa_init);
-module_exit(sdhci_pxa_exit);
-
-MODULE_DESCRIPTION("SDH controller driver for PXA168/PXA910/MMP2");
-MODULE_AUTHOR("Zhangfei Gao <zhangfei.gao@xxxxxxxxxxx>");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c
new file mode 100644
index 0000000..c5b99e0
--- /dev/null
+++ b/drivers/mmc/host/sdhci-pxav3.c
@@ -0,0 +1,305 @@
+/*
+ * Copyright (C) 2010 Marvell International Ltd.
+ * Zhangfei Gao <zhangfei.gao@xxxxxxxxxxx>
+ * Kevin Wang <dwang4@xxxxxxxxxxx>
+ * Mingwei Wang <mwwang@xxxxxxxxxxx>
+ * Philip Rakity <prakity@xxxxxxxxxxx>
+ * Mark Brown <markb@xxxxxxxxxxx>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+#include <plat/sdhci.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include "sdhci.h"
+#include "sdhci-pltfm.h"
+
+#define SD_CLOCK_BURST_SIZE_SETUP 0x10A
+#define SDCLK_SEL 0x100
+#define SDCLK_DELAY_SHIFT 9
+#define SDCLK_DELAY_MASK 0x1f
+
+#define SD_CFG_FIFO_PARAM 0x100
+#define SDCFG_GEN_PAD_CLK_ON (1<<6)
+#define SDCFG_GEN_PAD_CLK_CNT_MASK 0xFF
+#define SDCFG_GEN_PAD_CLK_CNT_SHIFT 24
+
+#define SD_SPI_MODE 0x108
+#define SD_CE_ATA_1 0x10C
+
+#define SD_CE_ATA_2 0x10E
+#define SDCE_MISC_INT (1<<2)
+#define SDCE_MISC_INT_EN (1<<1)
+
+static void pxav3_set_private_registers(struct sdhci_host *host, u8 mask)
+{
+ struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc));
+ struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
+
+ if (mask == SDHCI_RESET_ALL) {
+ /*
+ * tune timing of read data/command when crc error happen
+ * no performance impact
+ */
+ if (pdata && 0 != pdata->clk_delay_cycles) {
+ u16 tmp;
+
+ tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP);
+ tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK)
+ << SDCLK_DELAY_SHIFT;
+ tmp |= SDCLK_SEL;
+ writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP);
+ }
+ }
+}
+
+#define MAX_WAIT_COUNT 5
+static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
+ u16 tmp;
+ int count;
+
+ if (pxa->power_mode == MMC_POWER_UP
+ && power_mode == MMC_POWER_ON) {
+
+ dev_dbg(mmc_dev(host->mmc),
+ "%s: slot->power_mode = %d,"
+ "ios->power_mode = %d\n",
+ __func__,
+ pxa->power_mode,
+ power_mode);
+
+ /* set we want notice of when 74 clocks are sent */
+ tmp = readw(host->ioaddr + SD_CE_ATA_2);
+ tmp |= SDCE_MISC_INT_EN;
+ writew(tmp, host->ioaddr + SD_CE_ATA_2);
+
+ /* start sending the 74 clocks */
+ tmp = readw(host->ioaddr + SD_CFG_FIFO_PARAM);
+ tmp |= SDCFG_GEN_PAD_CLK_ON;
+ writew(tmp, host->ioaddr + SD_CFG_FIFO_PARAM);
+
+ /* slowest speed is about 100KHz or 10usec per clock */
+ udelay(740);
+ count = 0;
+
+ while (count++ < MAX_WAIT_COUNT) {
+ if ((readw(host->ioaddr + SD_CE_ATA_2)
+ & SDCE_MISC_INT) == 0)
+ break;
+ udelay(10);
+ }
+
+ if (count == MAX_WAIT_COUNT)
+ dev_warn(mmc_dev(host->mmc), "74 clock interrupt not cleared\n");
+
+ /* clear the interrupt bit if posted */
+ tmp = readw(host->ioaddr + SD_CE_ATA_2);
+ tmp |= SDCE_MISC_INT;
+ writew(tmp, host->ioaddr + SD_CE_ATA_2);
+ }
+ pxa->power_mode = power_mode;
+}
+
+static int pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
+{
+ u16 ctrl_2;
+
+ /*
+ * Set V18_EN -- UHS modes do not work without this.
+ * does not change signaling voltage
+ */
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+ /* Select Bus Speed Mode for host */
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ switch (uhs) {
+ case MMC_TIMING_UHS_SDR12:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
+ break;
+ case MMC_TIMING_UHS_SDR25:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
+ break;
+ case MMC_TIMING_UHS_SDR50:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR50 | SDHCI_CTRL_VDD_180;
+ break;
+ case MMC_TIMING_UHS_SDR104:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180;
+ break;
+ case MMC_TIMING_UHS_DDR50:
+ ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180;
+ break;
+ }
+
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+ dev_dbg(mmc_dev(host->mmc),
+ "%s uhs = %d, ctrl_2 = %04X\n",
+ __func__, uhs, ctrl_2);
+
+ return 0;
+}
+
+static unsigned int pxav3_get_ro(struct sdhci_host *host)
+{
+ /* Micro SD does not support write-protect feature */
+ return 0;
+}
+
+static struct sdhci_ops pxav3_sdhci_ops = {
+ .get_ro = pxav3_get_ro,
+ .platform_reset_exit = pxav3_set_private_registers,
+ .set_uhs_signaling = pxav3_set_uhs_signaling,
+ .platform_send_init_74_clocks = pxav3_gen_init_74_clocks,
+};
+
+static struct sdhci_ops pxav3_sdhci_wp_ops = {
+ .platform_reset_exit = pxav3_set_private_registers,
+ .set_uhs_signaling = pxav3_set_uhs_signaling,
+ .platform_send_init_74_clocks = pxav3_gen_init_74_clocks,
+};
+
+static int __devinit sdhci_pxav3_probe(struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct sdhci_host *host = NULL;
+ struct sdhci_pxa *pxa = NULL;
+ int ret;
+ struct clk *clk;
+
+ pxa = kzalloc(sizeof(struct sdhci_pxa), GFP_KERNEL);
+ if (!pxa)
+ return -ENOMEM;
+
+ host = sdhci_pltfm_init(pdev, NULL);
+ if (IS_ERR(host)) {
+ kfree(pxa);
+ return PTR_ERR(host);
+ }
+ pltfm_host = sdhci_priv(host);
+ pltfm_host->priv = pxa;
+
+ clk = clk_get(dev, "PXA-SDHCLK");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "failed to get io clock\n");
+ ret = PTR_ERR(clk);
+ goto err_clk_get;
+ }
+ pltfm_host->clk = clk;
+ clk_enable(clk);
+
+ host->quirks = SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
+ | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC;
+
+ /* enable 1/8V DDR capable */
+ host->mmc->caps |= MMC_CAP_1_8V_DDR;
+
+ if (pdata) {
+ if (pdata->flags & PXA_FLAG_CARD_PERMANENT) {
+ /* on-chip device */
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+ host->mmc->caps |= MMC_CAP_NONREMOVABLE;
+ }
+
+ /* If slot design supports 8 bit data, indicate this to MMC. */
+ if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT)
+ host->mmc->caps |= MMC_CAP_8_BIT_DATA;
+
+ if (pdata->quirks)
+ host->quirks |= pdata->quirks;
+ if (pdata->host_caps)
+ host->mmc->caps |= pdata->host_caps;
+ if (pdata->pm_caps)
+ host->mmc->pm_caps |= pdata->pm_caps;
+ }
+
+ if (pdata && pdata->flags & PXA_FLAG_CARD_NO_WP)
+ host->ops = &pxav3_sdhci_ops;
+ else
+ host->ops = &pxav3_sdhci_wp_ops;
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to add host\n");
+ goto err_add_host;
+ }
+
+ platform_set_drvdata(pdev, host);
+
+ return 0;
+
+err_add_host:
+ clk_disable(clk);
+ clk_put(clk);
+err_clk_get:
+ sdhci_pltfm_free(pdev);
+ kfree(pxa);
+ return ret;
+}
+
+static int __devexit sdhci_pxav3_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
+
+ sdhci_remove_host(host, 1);
+
+ clk_disable(pltfm_host->clk);
+ clk_put(pltfm_host->clk);
+ sdhci_pltfm_free(pdev);
+ kfree(pxa);
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver sdhci_pxav3_driver = {
+ .driver = {
+ .name = "sdhci-pxav3",
+ .owner = THIS_MODULE,
+ },
+ .probe = sdhci_pxav3_probe,
+ .remove = __devexit_p(sdhci_pxav3_remove),
+#ifdef CONFIG_PM
+ .suspend = sdhci_pltfm_suspend,
+ .resume = sdhci_pltfm_resume,
+#endif
+};
+static int __init sdhci_pxav3_init(void)
+{
+ return platform_driver_register(&sdhci_pxav3_driver);
+}
+
+static void __exit sdhci_pxav3_exit(void)
+{
+ platform_driver_unregister(&sdhci_pxav3_driver);
+}
+
+module_init(sdhci_pxav3_init);
+module_exit(sdhci_pxav3_exit);
+
+MODULE_DESCRIPTION("SDHCI driver for pxav3");
+MODULE_AUTHOR("Marvell International Ltd.");
+MODULE_LICENSE("GPL v2");
+
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
