On May 13, 2011, at 1:03 AM, zhangfei gao wrote:
> On Wed, May 11, 2011 at 5:47 AM, Philip Rakity <prakity@xxxxxxxxxxx> wrote:
>>
>> On May 11, 2011, at 2:28 AM, zhangfei gao wrote:
>>
>>> On Wed, May 11, 2011 at 4:52 AM, Philip Rakity <prakity@xxxxxxxxxxx> wrote:
>>>>
>>>> \
>>>> On May 11, 2011, at 1:48 AM, zhangfei gao wrote:
>>>>
>>>>> On Thu, May 5, 2011 at 2:49 AM, Arindam Nath <arindam.nath@xxxxxxx> wrote:
>>>>>> Marvell controller requires 1.8V bit in UHS control register 2
>>>>>> be set when doing UHS. eMMC does not require 1.8V for DDR.
>>>>>> add platform code to handle this.
>>>>>>
>>>>>> Signed-off-by: Philip Rakity <prakity@xxxxxxxxxxx>
>>>>>> Reviewed-by: Arindam Nath <arindam.nath@xxxxxxx>
>>>>>> ---
>>>>>> drivers/mmc/host/sdhci-pxa.c | 36 ++++++++++++++++++++++++++++++++++++
>>>>>> 1 files changed, 36 insertions(+), 0 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/mmc/host/sdhci-pxa.c b/drivers/mmc/host/sdhci-pxa.c
>>>>>> index 5a61208..b52c3e6 100644
>>>>>> --- a/drivers/mmc/host/sdhci-pxa.c
>>>>>> +++ b/drivers/mmc/host/sdhci-pxa.c
>>>>>> @@ -69,7 +69,40 @@ static void set_clock(struct sdhci_host *host, unsigned int clock)
>>>>>> }
>>>>>> }
>>>>>>
>>>>>> +static int set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
>>>>>> +{
>>>>>> + u16 ctrl_2;
>>>>>> +
>>>>>> + /*
>>>>>> + * Set V18_EN -- UHS modes do not work without this.
>>>>>> + * does not change signaling voltage
>>>>>> + */
>>>>>> + ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
>>>>>> +
>>>>>> + /* Select Bus Speed Mode for host */
>>>>>> + ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
>>>>>> + if (uhs == MMC_TIMING_UHS_SDR12)
>>>>>> + ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
>>>>>> + else if (uhs == MMC_TIMING_UHS_SDR25)
>>>>>> + ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
>>>>>> + else if (uhs == MMC_TIMING_UHS_SDR50) {
>>>>>> + ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
>>>>>> + ctrl_2 |= SDHCI_CTRL_VDD_180;
>>>>>> + } else if (uhs == MMC_TIMING_UHS_SDR104) {
>>>>>> + ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
>>>>>> + ctrl_2 |= SDHCI_CTRL_VDD_180;
>>>>>> + } else if (uhs == MMC_TIMING_UHS_DDR50) {
>>>>>> + ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
>>>>>> + ctrl_2 |= SDHCI_CTRL_VDD_180;
>>>>>> + }
>>>>>> + sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
>>>>>> + pr_debug("%s:%s uhs = %d, ctrl_2 = %04X\n",
>>>>>> + __func__, mmc_hostname(host->mmc), uhs, ctrl_2);
>>>>>> + return 0;
>>>>>> +}
>>>>>
>>>>> Why move common register accessing from sdhci.c to specific driver?
>>>>
>>>> In general case you do not know what the specific host controller work arounds are required.
>>>> on mmp2 this code works (no need for V18 for low speed UHS)
>>>> but other controllers it could be different
>>>
>>> Sorry, not understand, the patch is for sd uhs card or for emmc?
>>> For sd uhs card, no workaround is needed on mmp2, but require external
>>> pmic to provide 1.8v io voltage.
>>
>>
>> require 1.8V when setting UHS modes. See latest MMP2 Documentation.
>
> Do you mean set SDHCI_CTRL_VDD_180?
> It is already set in sdhci_start_signal_voltage_switch, so does not
> required in specific driver.
eMMC voltages are fixed. DDR support is available at 3.3v vcc and 3.3v vccq.
There is no voltage switch necessary. The card type value indicates that 3.3 vccq
or 1.8v vccq is available. Since we are communicating with the card DDR must
be available without a 1.8v vccq voltage switch.
mmp2 has the requirement that to do DDR at any vccq we must set the VDD_180 bit.
This bit set + DDR mode bit enables DDR. DDR mode bit on its own is not sufficient.
>
>>>
>>>>
>>>>>
>>>>>> +
>>>>>> static struct sdhci_ops sdhci_pxa_ops = {
>>>>>> + .set_uhs_signaling = set_uhs_signaling,
>>>>>> .set_clock = set_clock,
>>>>>> };
>>>>>>
>>>>>> @@ -141,6 +174,9 @@ static int __devinit sdhci_pxa_probe(struct platform_device *pdev)
>>>>>> if (pdata->quirks)
>>>>>> host->quirks |= pdata->quirks;
>>>>>>
>>>>>> + /* enable 1/8V DDR capable */
>>>>>> + host->mmc->caps |= MMC_CAP_1_8V_DDR;
>>>>>> +
>>>>>> /* If slot design supports 8 bit data, indicate this to MMC. */
>>>>>> if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT)
>>>>>> host->mmc->caps |= MMC_CAP_8_BIT_DATA;
>>>>>> --
>>>>>> 1.7.1
>>>>>>
>>>>>>
>>>>
>>>>
>>
>>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
