> -----Original Message----- > From: Arindam Nath [mailto:anath.amd@xxxxxxxxx] On Behalf Of Arindam > Nath > Sent: Friday, March 04, 2011 5:03 PM > To: cjb@xxxxxxxxxx > Cc: zhangfei.gao@xxxxxxxxx; prakity@xxxxxxxxxxx; > subhashj@xxxxxxxxxxxxxx; linux-mmc@xxxxxxxxxxxxxxx; henry.su@xxxxxxx; > aaron.lu@xxxxxxx; anath.amd@xxxxxxxxx; Arindam Nath > Subject: [PATCH v2 06/12] mmc: sd: add support for uhs bus speed mode > selection > > This patch adds support for setting UHS-I bus speed mode during UHS-I > initialization procedure. Since both the host and card can support > more than one bus speed, we select the highest speed based on both of > their capabilities. First we set the bus speed mode for the card using > CMD6 mode 1, and then we program the host controller to support the > required speed mode. We also set High Speed Enable in case one of the > UHS-I modes is selected. Since MMC_TIMING_UHS_SDR25 is same as > MMC_TIMING_SD_HS, we don't need to set the SDHCI_CTRL_HISPD flag for > UHS SDR25 again. We also take care to reset SD clock before setting > UHS mode in the Host Control2 register, and then re-enable it as per > the Host Controller spec v3.00. We set the clock frequency for the > UHS-I mode selected. > > Signed-off-by: Arindam Nath <arindam.nath@xxxxxxx> > --- > drivers/mmc/core/sd.c | 91 > ++++++++++++++++++++++++++++++++++++++++++++++ > drivers/mmc/host/sdhci.c | 32 +++++++++++++++- > drivers/mmc/host/sdhci.h | 5 +++ > include/linux/mmc/card.h | 16 ++++++++ > include/linux/mmc/host.h | 4 ++ > 5 files changed, 146 insertions(+), 2 deletions(-) > > diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c > index f6a4fab..ec0d8e6 100644 > --- a/drivers/mmc/core/sd.c > +++ b/drivers/mmc/core/sd.c > @@ -464,6 +464,92 @@ static int sd_select_driver_type(struct mmc_card > *card, u8 *status) > return 0; > } > > +static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status) > +{ > + unsigned int bus_speed, timing; > + int err; > + > + /* > + * If the host doesn't support any of the UHS-I modes, fallback > on > + * default speed. > + */ > + if (!(card->host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | > + MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))) > + return 0; > + > + if (card->host->caps & MMC_CAP_UHS_SDR104) { > + if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR104) { > + bus_speed = UHS_SDR104_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR104; > + card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR; > + } else if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR50) > { > + bus_speed = UHS_SDR50_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR50; > + card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR; > + } else if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_DDR50) > { > + bus_speed = UHS_DDR50_BUS_SPEED; > + timing = MMC_TIMING_UHS_DDR50; > + card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR; > + } else if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR25) > { > + bus_speed = UHS_SDR25_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR25; > + card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR; > + } > + } else if (card->host->caps & MMC_CAP_UHS_SDR50) { > + if ((card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR104) || > + (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR50)) { You can combine both modes with "or": if (card->sw_caps.uhs_bus_mode & (SD_MODE_UHS_SDR104 | SD_MODE_UHS_SDR50)). This can be done for many of the below checks. > + bus_speed = UHS_SDR50_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR50; > + card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR; > + } else if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_DDR50) > { > + bus_speed = UHS_DDR50_BUS_SPEED; > + timing = MMC_TIMING_UHS_DDR50; > + card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR; > + } else if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR25) > { > + bus_speed = UHS_SDR25_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR25; > + card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR; > + } > + } else if (card->host->caps & MMC_CAP_UHS_DDR50) { > + if ((card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR104) || > + (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR50) || > + (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_DDR50)) { > + bus_speed = UHS_DDR50_BUS_SPEED; > + timing = MMC_TIMING_UHS_DDR50; > + card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR; > + } else if (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR25) > { > + bus_speed = UHS_SDR25_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR25; > + card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR; > + } > + } else if (card->host->caps & MMC_CAP_UHS_SDR25) { > + if ((card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR104) || > + (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR50) || > + (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_DDR50) || > + (card->sw_caps.uhs_bus_mode & SD_MODE_UHS_SDR25)) { > + bus_speed = UHS_SDR25_BUS_SPEED; > + timing = MMC_TIMING_UHS_SDR25; > + card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR; > + } > + } > + > + err = mmc_sd_switch(card, 1, 0, bus_speed, status); For SDR12 mode, what will be the bus_speed? > + if (err) > + return err; > + > + if ((status[16] & 0xF) != bus_speed) > + printk(KERN_WARNING "%s: Problem setting bus speed > mode!\n", > + mmc_hostname(card->host)); > + else { For SDR12 mode, let's say you are setting the bus_speed = UHS_SDR12_BUS_SPEED (which is 0). Then for SDR12 mode there won't be a clock setting as you are checking if(buspeed). Is this what you want? How will you set the clock to 25 Mhz for SDR12 mode? > + if (bus_speed) { > + mmc_set_timing(card->host, timing); > + mmc_set_clock(card->host, card->sw_caps.uhs_max_dtr); > + } > + } > + > + return 0; > +} > + > /* > * UHS-I specific initialization procedure > */ > @@ -499,6 +585,11 @@ static int mmc_sd_init_uhs_card(struct mmc_card > *card) > > /* Set the driver strength for the card */ > err = sd_select_driver_type(card, status); > + if (err) > + goto out; > + > + /* Set bus speed mode of the card */ > + err = sd_set_bus_speed_mode(card, status); > > out: > kfree(status); > diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c > index 5d3bb11..f127fa2 100644 > --- a/drivers/mmc/host/sdhci.c > +++ b/drivers/mmc/host/sdhci.c > @@ -1278,7 +1278,13 @@ static void sdhci_set_ios(struct mmc_host *mmc, > struct mmc_ios *ios) > ctrl &= ~SDHCI_CTRL_HISPD; > > if (host->version >= SDHCI_SPEC_300) { > - u16 ctrl_2; > + u16 clk, ctrl_2; > + > + /* In case of UHS-I modes, set High Speed Enable */ > + if ((ios->timing == MMC_TIMING_UHS_SDR50) || > + (ios->timing == MMC_TIMING_UHS_SDR104) || > + (ios->timing == MMC_TIMING_UHS_DDR50)) > + ctrl |= SDHCI_CTRL_HISPD; > > ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); > if (!(ctrl_2 & SDHCI_CTRL_PRESET_VAL_ENABLE)) { > @@ -1300,7 +1306,6 @@ static void sdhci_set_ios(struct mmc_host *mmc, > struct mmc_ios *ios) > * need to reset SD Clock Enable before changing High > * Speed Enable to avoid generating clock gliches. > */ > - u16 clk; > > /* Reset SD Clock Enable */ > clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); > @@ -1313,6 +1318,29 @@ static void sdhci_set_ios(struct mmc_host *mmc, > struct mmc_ios *ios) > clk |= SDHCI_CLOCK_CARD_EN; > sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); > } > + > + ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); > + > + /* Select Bus Speed Mode for host */ > + if (ios->timing == MMC_TIMING_UHS_SDR25) > + ctrl_2 |= SDHCI_CTRL_UHS_SDR25; > + else if (ios->timing == MMC_TIMING_UHS_SDR50) > + ctrl_2 |= SDHCI_CTRL_UHS_SDR50; > + else if (ios->timing == MMC_TIMING_UHS_SDR104) > + ctrl_2 |= SDHCI_CTRL_UHS_SDR104; > + else if (ios->timing == MMC_TIMING_UHS_DDR50) > + ctrl_2 |= SDHCI_CTRL_UHS_DDR50; > + > + /* Reset SD Clock Enable */ > + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); > + clk &= ~SDHCI_CLOCK_CARD_EN; > + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); > + > + sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); > + > + /* Re-enable SD Clock */ > + clk |= SDHCI_CLOCK_CARD_EN; > + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); > } else > sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1); > > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h > index a407b5b..5bf244d 100644 > --- a/drivers/mmc/host/sdhci.h > +++ b/drivers/mmc/host/sdhci.h > @@ -150,6 +150,11 @@ > #define SDHCI_ACMD12_ERR 0x3C > > #define SDHCI_HOST_CONTROL2 0x3E > +#define SDHCI_CTRL_UHS_SDR12 0x0000 > +#define SDHCI_CTRL_UHS_SDR25 0x0001 > +#define SDHCI_CTRL_UHS_SDR50 0x0002 > +#define SDHCI_CTRL_UHS_SDR104 0x0003 > +#define SDHCI_CTRL_UHS_DDR50 0x0004 > #define SDHCI_CTRL_VDD_180 0x0008 > #define SDHCI_CTRL_DRV_TYPE_B 0x0000 > #define SDHCI_CTRL_DRV_TYPE_A 0x0010 > diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h > index 2d7f7a3..0b24c41 100644 > --- a/include/linux/mmc/card.h > +++ b/include/linux/mmc/card.h > @@ -75,7 +75,23 @@ struct sd_ssr { > > struct sd_switch_caps { > unsigned int hs_max_dtr; > + unsigned int uhs_max_dtr; > +#define UHS_SDR104_MAX_DTR 208000000 > +#define UHS_SDR50_MAX_DTR 100000000 > +#define UHS_DDR50_MAX_DTR 50000000 > +#define UHS_SDR25_MAX_DTR 50000000 > unsigned int uhs_bus_mode; > +#define UHS_SDR12_BUS_SPEED 0 > +#define UHS_SDR25_BUS_SPEED 1 > +#define UHS_SDR50_BUS_SPEED 2 > +#define UHS_SDR104_BUS_SPEED 3 > +#define UHS_DDR50_BUS_SPEED 4 > + > +#define SD_MODE_UHS_SDR12 (1 << UHS_SDR12_BUS_SPEED) > +#define SD_MODE_UHS_SDR25 (1 << UHS_SDR25_BUS_SPEED) > +#define SD_MODE_UHS_SDR50 (1 << UHS_SDR50_BUS_SPEED) > +#define SD_MODE_UHS_SDR104 (1 << UHS_SDR104_BUS_SPEED) > +#define SD_MODE_UHS_DDR50 (1 << UHS_DDR50_BUS_SPEED) > unsigned int uhs_drv_type; > #define SD_DRIVER_TYPE_B 0x01 > #define SD_DRIVER_TYPE_A 0x02 > diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h > index bc2121e..4dfff6d 100644 > --- a/include/linux/mmc/host.h > +++ b/include/linux/mmc/host.h > @@ -50,6 +50,10 @@ struct mmc_ios { > #define MMC_TIMING_LEGACY 0 > #define MMC_TIMING_MMC_HS 1 > #define MMC_TIMING_SD_HS 2 > +#define MMC_TIMING_UHS_SDR25 MMC_TIMING_SD_HS > +#define MMC_TIMING_UHS_SDR50 3 > +#define MMC_TIMING_UHS_SDR104 4 > +#define MMC_TIMING_UHS_DDR50 5 > > unsigned char ddr; /* dual data rate used */ > > -- > 1.7.1 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html