mmc->caps MMC_CAP_1_8V_DDR is set by looking at cabability_1
register if sd 3.0 controller.
Support for dual data rate (DDR50) with 1_8V signalling added
with optional call back to enable external control of signalling
voltage.
no support for 1.2V core voltage since SD 3.0 does not support
this.
**** QUESTION ****
should this be part of regulator framework ?
delay for signaling voltage to settle set to 5ms (per spec).
this code does not change the voltage supplied to the card.
It assumes that this is correctly handled in the core/ layer.
There is no requirement that the card voltage be at 1.8v
for DDR to work. This violates DDR specification for
SD Host Controller 3.0 since explicitly states card voltage
is 3.3v while signalling voltage is set to 1.8v.
tested on mmp2 -- brownstone -- under linux-next.
Note: this board design runs a fixed voltage to the card and
signaling voltage cannot be changed.
Signed-off-by: Philip Rakity <prakity@xxxxxxxxxxx>
---
drivers/mmc/host/sdhci.c | 53 ++++++++++++++++++++++++++++++++++++++++++---
drivers/mmc/host/sdhci.h | 5 ++++
2 files changed, 54 insertions(+), 4 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index d5febe5..805f850 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -84,6 +84,8 @@ static void sdhci_dumpregs(struct sdhci_host *host)
printk(KERN_DEBUG DRIVER_NAME ": Cmd: 0x%08x | Max curr: 0x%08x\n",
sdhci_readw(host, SDHCI_COMMAND),
sdhci_readl(host, SDHCI_MAX_CURRENT));
+ printk(KERN_DEBUG DRIVER_NAME ": HostCtrl2:0x%08x\n",
+ sdhci_readw(host, SDHCI_HOST_CONTROL_2));
if (host->flags & SDHCI_USE_ADMA)
printk(KERN_DEBUG DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
@@ -986,6 +988,38 @@ static void sdhci_finish_command(struct sdhci_host *host)
host->cmd = NULL;
}
+/*
+ * Handle 1.8V signaling for DDR. No need to check for other
+ * DDR values since driver supports ONLY 1_8V DDR. This is
+ * set by the MMC_CAP_1_8V_DDR. 1_2V DDR is not supported.
+ */
+static void sdhci_set_ddr(struct sdhci_host *host, unsigned int ddr)
+{
+ u16 con;
+
+ if (ddr == MMC_SDR_MODE)
+ return;
+
+ con = sdhci_readw(host, SDHCI_HOST_CONTROL_2);
+ con |= SDCTRL_2_SDH_V18_EN;
+ sdhci_writew(host, con, SDHCI_HOST_CONTROL_2);
+
+ /* Change sigalling voltage and wait for it to be stable */
+ if (host->ops->set_signaling_voltage)
+ host->ops->set_signaling_voltage(host, 18);
+ else
+ mdelay(5);
+
+ /*
+ * We can fail here but there is no higher level recovery
+ * since the card is already past the switch to ddr
+ */
+ con = sdhci_readw(host, SDHCI_HOST_CONTROL_2);
+ con &= ~SDCTRL_2_UHS_MODE_MASK;
+ con |= SDCTRL_2_UHS_MODE_SEL_DDR50;
+ sdhci_writew(host, con, SDHCI_HOST_CONTROL_2);
+}
+
static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
{
int div;
@@ -1180,6 +1214,7 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
}
sdhci_set_clock(host, ios->clock);
+ sdhci_set_ddr(host, ios->ddr);
if (ios->power_mode == MMC_POWER_OFF)
sdhci_set_power(host, -1);
@@ -1744,7 +1779,7 @@ EXPORT_SYMBOL_GPL(sdhci_alloc_host);
int sdhci_add_host(struct sdhci_host *host)
{
struct mmc_host *mmc;
- unsigned int caps, ocr_avail;
+ unsigned int caps, caps_h, ocr_avail;
int ret;
WARN_ON(host == NULL);
@@ -1767,8 +1802,19 @@ int sdhci_add_host(struct sdhci_host *host)
host->version);
}
- caps = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
- sdhci_readl(host, SDHCI_CAPABILITIES);
+ if (host->quirks & SDHCI_QUIRK_MISSING_CAPS) {
+ caps = host->caps;
+ caps_h = 0;
+ } else {
+ caps = sdhci_readl(host, SDHCI_CAPABILITIES);
+ if (host->version >= SDHCI_SPEC_300)
+ caps_h = sdhci_readl(host, SDHCI_CAPABILITIES_1);
+ else
+ caps_h = 0;
+ }
+
+ if (caps_h & SDHCI_CAN_DDR50)
+ mmc->caps |= MMC_CAP_1_8V_DDR;
if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
host->flags |= SDHCI_USE_SDMA;
@@ -1905,7 +1951,6 @@ int sdhci_add_host(struct sdhci_host *host)
ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
if (caps & SDHCI_CAN_VDD_180)
ocr_avail |= MMC_VDD_165_195;
-
mmc->ocr_avail = ocr_avail;
mmc->ocr_avail_sdio = ocr_avail;
if (host->ocr_avail_sdio)
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 36f3861..d976e4f 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -182,6 +182,9 @@
#define SDHCI_CAN_64BIT 0x10000000
#define SDHCI_CAPABILITIES_1 0x44
+#define SDHCI_CAN_SDR50 0x00000001
+#define SDHCI_CAN_SDR104 0x00000002
+#define SDHCI_CAN_DDR50 0x00000004
#define SDHCI_MAX_CURRENT 0x48
@@ -237,6 +240,8 @@ struct sdhci_ops {
void (*platform_send_init_74_clocks)(struct sdhci_host *host,
u8 power_mode);
unsigned int (*get_ro)(struct sdhci_host *host);
+ unsigned int (*set_signaling_voltage)(struct sdhci_host *host,
+ unsigned short voltage);
};
#ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
