Hello,
On Saturday, July 03, 2010 3:01 AM Kukjin Kim wrote:
> From: Hyuk Lee <hyuk1.lee@xxxxxxxxxxx>
>
> If host controller doesn't have WP pin which should be connnected with
> SDMMC
> card WP pin, can implement get_ro function with using the allocated gpio.
> In order to use this quirk wp_gpio in the platform data must be set.
>
> Signed-off-by: Hyuk Lee <hyuk1.lee@xxxxxxxxxxx>
> Signed-off-by: Kukjin Kim <kgene.kim@xxxxxxxxxxx>
> ---
> drivers/mmc/host/sdhci-s3c.c | 44
> ++++++++++++++++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci.c | 3 ++
> drivers/mmc/host/sdhci.h | 3 ++
> 3 files changed, 50 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
> index af21792..ed9376d 100644
> --- a/drivers/mmc/host/sdhci-s3c.c
> +++ b/drivers/mmc/host/sdhci-s3c.c
> @@ -18,11 +18,13 @@
> #include <linux/slab.h>
> #include <linux/clk.h>
> #include <linux/io.h>
> +#include <linux/gpio.h>
>
> #include <linux/mmc/host.h>
>
> #include <plat/sdhci.h>
> #include <plat/regs-sdhci.h>
> +#include <plat/gpio-cfg.h>
>
> #include "sdhci.h"
>
> @@ -209,6 +211,36 @@ static void sdhci_s3c_set_clock(struct sdhci_host
> *host, unsigned int clock)
> }
> }
>
> +/**
> + * sdhci_s3c_get_ro - callback for get_ro
> + * @host: The SDHCI host being changed
> + *
> + * If the WP pin is connected with GPIO, can get the value which indicates
> + * the card is locked or not.
> +*/
> +static int sdhci_s3c_get_ro(struct mmc_host *mmc)
> +{
> + struct sdhci_s3c *sc;
> + struct sdhci_host *host;
> +
> + host = mmc_priv(mmc);
> + sc = sdhci_priv(host);
> +
> + return gpio_get_value(sc->pdata->wp_gpio);
> +}
> +
> +/**
> + * sdhci_s3c_cfg_wp - configure GPIO for WP pin
> + * @gpio_num: GPIO number which connected with WP line from SD/MMC slot
> + *
> + * Configure GPIO for using WP line
> +*/
> +static void sdhci_s3c_cfg_wp(unsigned int gpio_num)
> +{
> + s3c_gpio_cfgpin(gpio_num, S3C_GPIO_INPUT);
> + s3c_gpio_setpull(gpio_num, S3C_GPIO_PULL_UP);
> +}
> +
> static struct sdhci_ops sdhci_s3c_ops = {
> .get_max_clock = sdhci_s3c_get_max_clk,
> .get_timeout_clock = sdhci_s3c_get_timeout_clk,
> @@ -311,6 +343,9 @@ static int __devinit sdhci_s3c_probe(struct
> platform_device *pdev)
> if (pdata->cfg_gpio)
> pdata->cfg_gpio(pdev, pdata->max_width);
>
> + if (pdata->wp_gpio)
> + sdhci_s3c_ops.get_ro = sdhci_s3c_get_ro;
> +
> host->hw_name = "samsung-hsmmc";
> host->ops = &sdhci_s3c_ops;
> host->quirks = 0;
> @@ -335,6 +370,15 @@ static int __devinit sdhci_s3c_probe(struct
> platform_device *pdev)
> host->quirks |= (SDHCI_QUIRK_32BIT_DMA_ADDR |
> SDHCI_QUIRK_32BIT_DMA_SIZE);
>
> + /* Controller's WP pin donsn't connected with SD card. So we allocate
> + * a GPIO for getting WP data from SD card and use that data as
> + * the return value of the get_ro function */
> + host->quirks |= SDHCI_QUIRK_NO_WP_BIT;
> +
> + /* to configure gpio pin as a card write protection signal */
> + if (pdata->wp_gpio)
> + sdhci_s3c_cfg_wp(pdata->wp_gpio);
> +
Assuming that pdata->wp_gpio == 0 means that the board has no additional wp
feature is wrong from the 'good and clean' API point of view. For example
GPIO_A0(0) pin for S5PV210 is gpio number 0. This would mean that it cannot
be used for this feature at all.
I was told to use gpio_is_valid() macro and use -1 as 'invalid gpio' pin
number for implementing similar checks.
Best regards
--
Marek Szyprowski
Samsung Poland R&D Center
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
