I would like to use the SD card slot on my Dell D420 laptop, but inserting
a card fails with:
mmc0: error -84 whilst initialising SD card
According to lspci, the device is:
02:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 18)
I tried various kernel versions, including 2.6.32.15, 2.6.33, 2.6.34 and
2.6.35-rc2.
If I'm correct, 2.6.32 kernel uses ricoh_mmc to fix a quirk with this
controller, whereas for newer kernels CONFIG_MMC_RICOH_MMC is necessary.
In either case I still get the same error.
I'm summarised the debug messages below from my 2.6.35-rc2 with debug,
full dmesg is attached.
As this model is mentioned in sdhci-pci.c I assume it has been used
successfully; any what the cause of the problem is?
The end of the output when inserting a card is:
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD7): 0: 00000700 00000000 00000000 00000000
mmc0: starting CMD55 arg b3680000 flags 00000095
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000920 00000000 00000000 00000000
mmc0: starting CMD51 arg 00000000 flags 000000b5
mmc0: blksz 8 blocks 1 flags 00000200 tsac 100 ms nsac 0
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00408000
mmc0: req done (CMD51): 0: 00000920 00000000 00000000 00000000
mmc0: 0 bytes transferred: -84
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc0: error -84 whilst initialising SD card
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
The "clock 0Hz" was previously 400000Hz in earlier messages.
On both initialisation and inserting a card, there are many blocks of the
form:
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
The commands and flags show variation (see attached dmesg) so a newcomer
like me they aren't clearly a sign of an error or re-trying. Any ideas?
Thanks
--
Mark
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.35-rc2 (mark@vega) (gcc version 4.5.0 (GCC) ) #2 SMP PREEMPT Wed Jun 9 23:39:51 BST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f681400 (usable)
BIOS-e820: 000000007f681400 - 0000000080000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4007000 (reserved)
BIOS-e820: 00000000f4008000 - 00000000f400c000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
DMI 2.4 present.
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x7f681 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-EFFFF uncachable
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07F800000 mask FFF800000 uncachable
2 base 07F700000 mask FFFF00000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
PAT not supported by CPU.
e820 update range: 0000000000002000 - 0000000000010000 (usable) ==> (reserved)
Scanning 1 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000001000 (reserved)
modified: 0000000000001000 - 0000000000002000 (usable)
modified: 0000000000002000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009f000 (usable)
modified: 000000000009f000 - 00000000000a0000 (reserved)
modified: 0000000000100000 - 000000007f681400 (usable)
modified: 000000007f681400 - 0000000080000000 (reserved)
modified: 00000000f0000000 - 00000000f4007000 (reserved)
modified: 00000000f4008000 - 00000000f400c000 (reserved)
modified: 00000000fec00000 - 00000000fec10000 (reserved)
modified: 00000000fed20000 - 00000000feda0000 (reserved)
modified: 00000000fee00000 - 00000000fee10000 (reserved)
modified: 00000000ffb00000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 15000-1a000
RAMDISK: 7f487000 - 7f672000
Allocated new RAMDISK: 00100000 - 002ea339
Move RAMDISK from 000000007f487000 - 000000007f671338 to 00100000 - 002ea338
ACPI: RSDP 000fc0e0 00014 (v00 DELL )
ACPI: RSDT 7f681a0e 00048 (v01 DELL M07 27D70403 ASL 00000061)
ACPI: FACP 7f682800 00074 (v01 DELL M07 27D70403 ASL 00000061)
ACPI: DSDT 7f683400 04D15 (v01 INT430 SYSFexxx 00001001 INTL 20050624)
ACPI: FACS 7f691c00 00040
ACPI: HPET 7f682f00 00038 (v01 DELL M07 00000001 ASL 00000061)
ACPI: APIC 7f683000 00068 (v01 DELL M07 27D70403 ASL 00000047)
ACPI: ASF! 7f682c00 0005B (v16 DELL M07 27D70403 ASL 00000061)
ACPI: MCFG 7f682fc0 0003E (v16 DELL M07 27D70403 ASL 00000061)
ACPI: SLIC 7f68309c 00176 (v01 DELL M07 27D70403 ASL 00000061)
ACPI: TCPA 7f683300 00032 (v01 DELL M07 27D70403 ASL 00000061)
ACPI: BOOT 7f682bc0 00028 (v01 DELL M07 27D70403 ASL 00000061)
ACPI: SSDT 7f681a99 004DC (v01 PmRef CpuPm 00003000 INTL 20050624)
ACPI: Local APIC address 0xfee00000
1150MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
Zone PFN ranges:
DMA 0x00000001 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007f681
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000001 -> 0x00000002
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007f681
On node 0 totalpages: 521745
free_area_init_node: node 0, pgdat c140e040, node_mem_map c1570020
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3952 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2302 pages used for memmap
HighMem zone: 292229 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
early_res array is doubled to 64 at [16000 - 167ff]
PM: Registered nosave memory: 0000000000002000 - 0000000000010000
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 80000000:70000000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 14 pages/cpu @c2800000 s34880 r0 d22464 u2097152
pcpu-alloc: s34880 r0 d22464 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517667
Kernel command line: root=/dev/sda5 ro resume=/dev/sda7
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
allocated 10437120 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Subtract (46 early reservations)
#1 [0000001000 - 0000002000] EX TRAMPOLINE
#2 [0001000000 - 0001567184] TEXT DATA BSS
#3 [000009f000 - 0000100000] BIOS reserved
#4 [0001568000 - 000156e194] BRK
#5 [0000010000 - 0000011000] TRAMPOLINE
#6 [0000011000 - 0000015000] ACPI WAKEUP
#7 [0000015000 - 0000016000] PGTABLE
#8 [0000100000 - 00002eb000] NEW RAMDISK
#9 [000156f000 - 0001570000] BOOTMEM
#10 [0001570000 - 0002560000] BOOTMEM
#11 [00015671c0 - 00015671c4] BOOTMEM
#12 [0001567200 - 00015672c0] BOOTMEM
#13 [00015672c0 - 0001567314] BOOTMEM
#14 [0002560000 - 0002563000] BOOTMEM
#15 [0001567340 - 00015673ac] BOOTMEM
#16 [0002563000 - 0002569000] BOOTMEM
#17 [00015673c0 - 00015673e5] BOOTMEM
#18 [0001567400 - 0001567427] BOOTMEM
#19 [0001567440 - 00015675ac] BOOTMEM
#20 [00015675c0 - 0001567600] BOOTMEM
#21 [0001567600 - 0001567640] BOOTMEM
#22 [0001567640 - 0001567680] BOOTMEM
#23 [0001567680 - 00015676c0] BOOTMEM
#24 [00015676c0 - 0001567700] BOOTMEM
#25 [0001567700 - 0001567740] BOOTMEM
#26 [0001567740 - 0001567780] BOOTMEM
#27 [0001567780 - 00015677c0] BOOTMEM
#28 [00015677c0 - 0001567800] BOOTMEM
#29 [0001567800 - 0001567840] BOOTMEM
#30 [0001567840 - 0001567850] BOOTMEM
#31 [0001567880 - 0001567890] BOOTMEM
#32 [00015678c0 - 00015678e3] BOOTMEM
#33 [0001567900 - 0001567923] BOOTMEM
#34 [0002800000 - 000280e000] BOOTMEM
#35 [0002a00000 - 0002a0e000] BOOTMEM
#36 [0001567940 - 0001567944] BOOTMEM
#37 [0001567980 - 0001567984] BOOTMEM
#38 [00015679c0 - 00015679c8] BOOTMEM
#39 [0001567a00 - 0001567a08] BOOTMEM
#40 [0001567a40 - 0001567ae8] BOOTMEM
#41 [0001567b00 - 0001567b68] BOOTMEM
#42 [0002569000 - 000256d000] BOOTMEM
#43 [000256d000 - 00025ed000] BOOTMEM
#44 [00025ed000 - 000262d000] BOOTMEM
#45 [0002a0e000 - 0003402200] BOOTMEM
Initializing HighMem for node 0 (000377fe:0007f681)
Memory: 2051972k/2087428k available (2958k kernel code, 35008k reserved, 1223k data, 412k init, 1178124k highmem)
virtual kernel memory layout:
fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1416000 - 0xc147d000 ( 412 kB)
.data : 0xc12e38b8 - 0xc1415880 (1223 kB)
.text : 0xc1000000 - 0xc12e38b8 (2958 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:512
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 1196.770 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 2394.27 BogoMIPS (lpj=3989233)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Events: Core events, core PMU driver.
... version: 1
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 0
... event mask: 0000000000000003
ACPI: Core revision 20100428
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM) Duo CPU U2500 @ 1.20GHz stepping 0c
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
TSC synchronization [CPU#0 -> CPU#1]:
Measured 2238676029 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
Brought up 2 CPUs
Total of 2 processors activated (4789.07 BogoMIPS).
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI Warning: Incorrect checksum in table [TCPA] - 0x00, should be 0xA9 (20100428/tbutils-314)
ACPI: SSDT 7f681a56 00043 (v01 LMPWR DELLLOM 00001001 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00043 (v01 LMPWR DELLLOM 00001001 INTL 20050624)
ACPI: SSDT 7f6821c0 001C0 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 001C0 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
ACPI: SSDT 7f681f75 001C6 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 001C6 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
ACPI: SSDT 7f682380 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
ACPI: SSDT 7f68213b 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: ACPI Dock Station Driver: 1 docks/bays found
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xefffffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xf4007000-0xf4007fff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xf400c000-0xfebfffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xfec10000-0xfecfffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xfed00400-0xfed1ffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfed44fff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xfee10000-0xffafffff] (ignored)
pci 0000:00:02.0: reg 10: [mem 0xeff00000-0xeff7ffff]
pci 0000:00:02.0: reg 14: [io 0xeff8-0xefff]
pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff pref]
pci 0000:00:02.0: reg 1c: [mem 0xefec0000-0xefefffff]
pci 0000:00:02.1: reg 10: [mem 0xeff80000-0xefffffff]
pci 0000:00:1b.0: reg 10: [mem 0xefebc000-0xefebffff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1d.0: reg 20: [io 0xbf80-0xbf9f]
pci 0000:00:1d.1: reg 20: [io 0xbf60-0xbf7f]
pci 0000:00:1d.2: reg 20: [io 0xbf40-0xbf5f]
pci 0000:00:1d.3: reg 20: [io 0xbf20-0xbf3f]
pci 0000:00:1d.7: reg 10: [mem 0xffa80000-0xffa803ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x1080-0x10bf] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0900 (mask 007f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0c80 (mask 003f)
pci 0000:00:1f.1: reg 10: [io 0x01f0-0x01f7]
pci 0000:00:1f.1: reg 14: [io 0x03f4-0x03f7]
pci 0000:00:1f.1: reg 18: [io 0x0170-0x0177]
pci 0000:00:1f.1: reg 1c: [io 0x0374-0x0377]
pci 0000:00:1f.1: reg 20: [io 0xbfa0-0xbfaf]
pci 0000:00:1f.3: reg 20: [io 0x10c0-0x10df]
pci 0000:00:1c.0: PCI bridge to [bus 0b-0b]
pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:0c:00.0: reg 10: [mem 0xefdff000-0xefdfffff]
pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:00:1c.1: PCI bridge to [bus 0c-0c]
pci 0000:00:1c.1: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.1: bridge window [mem 0xefd00000-0xefdfffff]
pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:09:00.0: reg 10: [mem 0xefcf0000-0xefcfffff 64bit]
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:00:1c.2: PCI bridge to [bus 09-09]
pci 0000:00:1c.2: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.2: bridge window [mem 0xefc00000-0xefcfffff]
pci 0000:00:1c.2: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:02:01.0: reg 10: [mem 0x00000000-0x00000fff]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:01.1: reg 10: [mem 0xefbff800-0xefbfffff]
pci 0000:02:01.1: supports D1 D2
pci 0000:02:01.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:01.1: PME# disabled
pci 0000:02:01.2: reg 10: [mem 0xefbff700-0xefbff7ff]
pci 0000:02:01.2: supports D1 D2
pci 0000:02:01.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:01.2: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 02-03] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xefb00000-0xefbfffff]
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
pci_bus 0000:03: [bus 03-06] partially hidden behind transparent bridge 0000:02 [bus 02-03]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PXP0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5 7)
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *3
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 0000000000002000 - 000000000000ffff
reserve RAM buffer: 000000000009f000 - 000000000009ffff
reserve RAM buffer: 000000007f681400 - 000000007fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:02: disabling [io 0x1000-0x1005] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
pnp 00:02: disabling [io 0x1008-0x100f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
pnp 00:03: disabling [io 0x1006-0x1007] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
pnp 00:03: disabling [io 0x100a-0x1059] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
pnp 00:03: disabling [io 0x1060-0x107f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
pnp 00:03: disabling [io 0x1010-0x102f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0x00000000-0x0009fbff] could not be reserved
system 00:00: [mem 0x0009fc00-0x0009ffff] could not be reserved
system 00:00: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:00: [mem 0x00100000-0x7f6813ff] could not be reserved
system 00:00: [mem 0x7f681400-0x7f6fffff] has been reserved
system 00:00: [mem 0x7f700000-0x7f7fffff] has been reserved
system 00:00: [mem 0x7f700000-0x7fefffff] could not be reserved
system 00:00: [mem 0xffb00000-0xffffffff] has been reserved
system 00:00: [mem 0xfec00000-0xfec0ffff] could not be reserved
system 00:00: [mem 0xfee00000-0xfee0ffff] has been reserved
system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:00: [mem 0xfed45000-0xfed9ffff] has been reserved
system 00:00: [mem 0xffa80000-0xffa83fff] could not be reserved
system 00:00: [mem 0xf4000000-0xf4003fff] has been reserved
system 00:00: [mem 0xf4004000-0xf4004fff] has been reserved
system 00:00: [mem 0xf4005000-0xf4005fff] has been reserved
system 00:00: [mem 0xf4006000-0xf4006fff] has been reserved
system 00:00: [mem 0xf4008000-0xf400bfff] has been reserved
system 00:00: [mem 0xf0000000-0xf3ffffff] has been reserved
system 00:02: [io 0x04d0-0x04d1] has been reserved
system 00:03: [io 0xf400-0xf4fe] has been reserved
system 00:03: [io 0x1080-0x10bf] has been reserved
system 00:03: [io 0x10c0-0x10df] has been reserved
system 00:03: [io 0x0809] has been reserved
system 00:08: [io 0x0c80-0x0caf] has been reserved
system 00:08: [io 0x0cc0-0x0cff] could not be reserved
system 00:08: [io 0x0910-0x091f] has been reserved
system 00:08: [io 0x0920-0x092f] has been reserved
system 00:08: [io 0x0cbc-0x0cbf] has been reserved
system 00:08: [io 0x0930-0x097f] has been reserved
system 00:0b: [mem 0xfed00000-0xfed003ff] has been reserved
system 00:0c: [io 0x0cb0-0x0cbb] has been reserved
system 00:0c: [mem 0xfed40000-0xfed44fff] has been reserved
pci 0000:00:1e.0: BAR 15: assigned [mem 0x80000000-0x83ffffff pref]
pci 0000:00:1c.0: BAR 14: assigned [mem 0x84000000-0x841fffff]
pci 0000:00:1c.0: BAR 15: assigned [mem 0x84200000-0x843fffff 64bit pref]
pci 0000:00:1c.1: BAR 15: assigned [mem 0x84400000-0x845fffff 64bit pref]
pci 0000:00:1c.2: BAR 15: assigned [mem 0x84600000-0x847fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
pci 0000:00:1c.1: BAR 13: assigned [io 0x3000-0x3fff]
pci 0000:00:1c.2: BAR 13: assigned [io 0x4000-0x4fff]
pci 0000:00:1e.0: BAR 13: assigned [io 0x5000-0x5fff]
pci 0000:00:1c.0: PCI bridge to [bus 0b-0b]
pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:1c.0: bridge window [mem 0x84000000-0x841fffff]
pci 0000:00:1c.0: bridge window [mem 0x84200000-0x843fffff 64bit pref]
pci 0000:00:1c.1: PCI bridge to [bus 0c-0c]
pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
pci 0000:00:1c.1: bridge window [mem 0xefd00000-0xefdfffff]
pci 0000:00:1c.1: bridge window [mem 0x84400000-0x845fffff 64bit pref]
pci 0000:00:1c.2: PCI bridge to [bus 09-09]
pci 0000:00:1c.2: bridge window [io 0x4000-0x4fff]
pci 0000:00:1c.2: bridge window [mem 0xefc00000-0xefcfffff]
pci 0000:00:1c.2: bridge window [mem 0x84600000-0x847fffff 64bit pref]
pci 0000:02:01.0: BAR 15: assigned [mem 0x80000000-0x83ffffff pref]
pci 0000:02:01.0: BAR 16: assigned [mem 0x88000000-0x8bffffff]
pci 0000:02:01.0: BAR 0: assigned [mem 0xefb00000-0xefb00fff]
pci 0000:02:01.0: BAR 0: set to [mem 0xefb00000-0xefb00fff] (PCI address [0xefb00000-0xefb00fff]
pci 0000:02:01.0: BAR 13: assigned [io 0x5000-0x50ff]
pci 0000:02:01.0: BAR 14: assigned [io 0x5400-0x54ff]
pci 0000:02:01.0: CardBus bridge to [bus 03-06]
pci 0000:02:01.0: bridge window [io 0x5000-0x50ff]
pci 0000:02:01.0: bridge window [io 0x5400-0x54ff]
pci 0000:02:01.0: bridge window [mem 0x80000000-0x83ffffff pref]
pci 0000:02:01.0: bridge window [mem 0x88000000-0x8bffffff]
pci 0000:00:1e.0: PCI bridge to [bus 02-03]
pci 0000:00:1e.0: bridge window [io 0x5000-0x5fff]
pci 0000:00:1e.0: bridge window [mem 0xefb00000-0xefbfffff]
pci 0000:00:1e.0: bridge window [mem 0x80000000-0x83ffffff pref]
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:02:01.0: enabling device (0000 -> 0003)
pci 0000:02:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:0b: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:0b: resource 1 [mem 0x84000000-0x841fffff]
pci_bus 0000:0b: resource 2 [mem 0x84200000-0x843fffff 64bit pref]
pci_bus 0000:0c: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:0c: resource 1 [mem 0xefd00000-0xefdfffff]
pci_bus 0000:0c: resource 2 [mem 0x84400000-0x845fffff 64bit pref]
pci_bus 0000:09: resource 0 [io 0x4000-0x4fff]
pci_bus 0000:09: resource 1 [mem 0xefc00000-0xefcfffff]
pci_bus 0000:09: resource 2 [mem 0x84600000-0x847fffff 64bit pref]
pci_bus 0000:02: resource 0 [io 0x5000-0x5fff]
pci_bus 0000:02: resource 1 [mem 0xefb00000-0xefbfffff]
pci_bus 0000:02: resource 2 [mem 0x80000000-0x83ffffff pref]
pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
pci_bus 0000:03: resource 0 [io 0x5000-0x50ff]
pci_bus 0000:03: resource 1 [io 0x5400-0x54ff]
pci_bus 0000:03: resource 2 [mem 0x80000000-0x83ffffff pref]
pci_bus 0000:03: resource 3 [mem 0x88000000-0x8bffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 64 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 1964k freed
Simple Boot Flag at 0x79 set to 0x1
apm: BIOS not found.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1276124231.583:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1710
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
pcieport 0000:00:1c.2: setting latency timer to 64
pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
pcieport 0000:00:1c.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.0: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.0:pcie01 failed with error -13
pcieport 0000:00:1c.1: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.1: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.1:pcie01 failed with error -13
pcieport 0000:00:1c.2: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.2: Failed to receive control of PCIe PME service: no _OSC support
pcie_pme: probe of 0000:00:1c.2:pcie01 failed with error -13
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
PM: Checking image partition /dev/sda7
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
PM: Resume from disk failed.
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 412k freed
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
ata2: port disabled. ignoring.
ata1.00: ATA-6: TOSHIBA MK6008GAH, BU022C, max UDMA/100
ata1.00: 117210240 sectors, multi 8: LBA
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK6008GA BU02 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 117210240 512-byte logical blocks: (60.0 GB/55.8 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sda5
Ending clean XFS mount for filesystem: sda5
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
udev: starting version 151
sd 0:0:0:0: Attached scsi generic sg0 type 0
cfg80211: Calling CRDA to update world regulatory domain
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM] (64 C)
ACPI: acpi_idle registered with cpuidle
input: PC Speaker as /devices/platform/pcspkr/input/input1
input: DualPoint Stick as /devices/platform/i8042/serio1/input/input2
input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input3
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
tg3.c:v3.110 (April 9, 2010)
tg3 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
tg3 0000:09:00.0: setting latency timer to 64
tg3 0000:09:00.0: eth0: Tigon3 [partno(BCM5752KFBG) rev 6002] (PCI Express) MAC address 00:18:8b:d6:5d:91
tg3 0000:09:00.0: eth0: attached PHY is 5752 (10/100/1000Base-T Ethernet) (WireSpeed[1])
tg3 0000:09:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
tg3 0000:09:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: using broken periodic workaround
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xffa80000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Linux agpgart interface v0.103
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
ACPI: Lid Switch [LID]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
ACPI: Power Button [PBTN]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input6
ACPI: Sleep Button [SBTN]
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input7
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
usb 1-2: new high speed USB device using ehci_hcd and address 2
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000bf80
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000bf60
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000bf40
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000bf20
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: Battery Slot [BAT0] (battery present)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
yenta_cardbus 0000:02:01.0: CardBus bridge found [1028:01d6]
input: HDA Intel Mic at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
agpgart-intel 0000:00:00.0: Intel 945GM Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
ACPI: AC Adapter [AC] (on-line)
intel_rng: FWH not detected
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
yenta_cardbus 0000:02:01.0: ISA IRQ mask 0x0cb8, PCI irq 19
yenta_cardbus 0000:02:01.0: Socket status: 30000006
pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge window: [io 0x5000-0x5fff]
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x5000-0x5fff: excluding 0x5000-0x50ff 0x5400-0x54ff
yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge window: [mem 0xefb00000-0xefbfffff]
pcmcia_socket pcmcia_socket0: cs: memory probe 0xefb00000-0xefbfffff: excluding 0xefb00000-0xefb0ffff 0xefbf0000-0xefbfffff
yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge window: [mem 0x80000000-0x83ffffff pref]
pcmcia_socket pcmcia_socket0: cs: memory probe 0x80000000-0x83ffffff: excluding 0x80000000-0x83ffffff
ACPI: WMI: Mapper loaded
usb 1-2.3: new full speed USB device using ehci_hcd and address 3
hub 1-2.3:1.0: USB hub found
hub 1-2.3:1.0: 3 ports detected
input: Dell WMI hotkeys as /devices/virtual/input/input10
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x377
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: excluding 0xc80-0xcbf
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xc7fff 0xcc000-0xcffff 0xf0000-0xfffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
firewire_ohci 0000:02:01.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
usb 1-2.3.2: new full speed USB device using ehci_hcd and address 4
firewire_ohci: Added fw-ohci device 0000:02:01.1, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x0
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
iTCO_vendor_support: vendor-support=0
sdhci-pci 0000:02:01.2: SDHCI controller found [1180:0822] (rev 18)
sdhci-pci 0000:02:01.2: found 1 slot(s)
sdhci-pci 0000:02:01.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
sdhci: ============== REGISTER DUMP ==============
sdhci: Sys addr: 0x00000000 | Version: 0x00000200
sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci: Present: 0x01f70000 | Host ctl: 0x00000000
sdhci: Power: 0x00000000 | Blk gap: 0x00000000
sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci: Int enab: 0x00ff0003 | Sig enab: 0x00ff0003
sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci: Caps: 0x01e021a1 | Max curr: 0x00000040
sdhci: ===========================================
Registered led device: mmc0::
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc0: SDHCI controller on PCI [0000:02:01.2] using DMA
mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0 timing 0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD52 arg 00000c00 flags 00000195
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD52 arg 80000c08 flags 00000195
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc0: starting CMD0 arg 00000000 flags 000000c0
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD8 arg 000001aa flags 000002f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req failed (CMD5): -110, retrying...
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req failed (CMD5): -110, retrying...
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req failed (CMD5): -110, retrying...
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD1 arg 00000000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
leds_ss4200: no LED devices found
[drm] Initialized drm 1.1.0 20060810
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:s
iwl3945: Copyright(c) 2003-2010 Intel Corporation
iwl3945 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwl3945 0000:0c:00.0: setting latency timer to 64
iwl3945 0000:0c:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
iwl3945 0000:0c:00.0: Detected Intel Wireless WiFi Link 3945ABG
iwl3945 0000:0c:00.0: irq 44 for MSI/MSI-X
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
[drm] set up 7M of stolen space
firewire_core: created device fw0: GUID 484fc0003bba7850, S400
[drm] initialized overlay support
phy0: Selected rate control algorithm 'iwl-3945-rs'
Console: switching to colour frame buffer device 160x50
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
Slow work thread pool: Starting up
Slow work thread pool: Ready
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@xxxxxxxxxx
padlock: VIA PadLock not detected.
padlock: VIA PadLock Hash Engine not detected.
Btrfs loaded
device fsid 4142ea38cfbac52f-1988df0c32213bbc devid 1 transid 14904 /dev/mapper/sda6x
device fsid 4142ea38cfbac52f-1988df0c32213bbc devid 1 transid 14904 /dev/mapper/sda6x
device fsid 4142ea38cfbac52f-1988df0c32213bbc devid 1 transid 14904 /dev/mapper/sda6x
device fsid 4142ea38cfbac52f-1988df0c32213bbc devid 1 transid 14904 /dev/mapper/sda6x
Adding 2040216k swap on /dev/sda7. Priority:-1 extents:1 across:2040216k
tg3 0000:09:00.0: irq 45 for MSI/MSI-X
iwl3945 0000:0c:00.0: loaded firmware version 15.32.2.9
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: deauthenticating from 00:0d:93:8a:7f:0d by local choice (reason=3)
wlan0: authenticate with 00:0d:93:8a:7f:0d (try 1)
wlan0: authenticated
wlan0: associate with 00:0d:93:8a:7f:0d (try 1)
wlan0: RX AssocResp from 00:0d:93:8a:7f:0d (capab=0x411 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: no IPv6 routers present
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000080
mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0 timing 0
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD52 arg 00000c00 flags 00000195
mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD52 arg 80000c08 flags 00000195
mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc0: starting CMD0 arg 00000000 flags 000000c0
mmc0: req done (CMD0): -123: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD8 arg 000001aa flags 000002f5
mmc0: req done (CMD8): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
mmc0: req failed (CMD5): -123, retrying...
mmc0: req failed (CMD5): -123, retrying...
mmc0: req failed (CMD5): -123, retrying...
mmc0: req done (CMD5): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
mmc0: starting CMD1 arg 00000000 flags 000000e1
mmc0: req done (CMD1): -123: 00000000 00000000 00000000 00000000
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000040
mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0 timing 0
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD52 arg 00000c00 flags 00000195
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD52 arg 80000c08 flags 00000195
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc0: starting CMD0 arg 00000000 flags 000000c0
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc0: starting CMD8 arg 000001aa flags 000002f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD5 arg 00000000 flags 000002e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req failed (CMD5): -110, retrying...
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req failed (CMD5): -110, retrying...
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req failed (CMD5): -110, retrying...
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00400120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00000000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 20 width 0 timing 0
mmc0: starting CMD0 arg 00000000 flags 000000c0
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc0: starting CMD8 arg 000001aa flags 000002f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00018000
mmc0: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00400120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 00ff8000 00000000 00000000 00000000
mmc0: starting CMD55 arg 00000000 flags 000000f5
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000
mmc0: starting CMD41 arg 00300000 flags 000000e1
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD41): 0: 80ff8000 00000000 00000000 00000000
mmc0: starting CMD2 arg 00000000 flags 00000067
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD2): 0: 1b534d53 44202020 10dac1bf 4b007c00
mmc0: starting CMD3 arg 00000000 flags 00000075
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD3): 0: b3680500 00000000 00000000 00000000
mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc0: starting CMD9 arg b3680000 flags 00000007
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD9): 0: 002f0032 5f5a83cf 2db7ffbf 96800000
mmc0: starting CMD7 arg b3680000 flags 00000015
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD7): 0: 00000700 00000000 00000000 00000000
mmc0: starting CMD55 arg b3680000 flags 00000095
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
mmc0: req done (CMD55): 0: 00000920 00000000 00000000 00000000
mmc0: starting CMD51 arg 00000000 flags 000000b5
mmc0: blksz 8 blocks 1 flags 00000200 tsac 100 ms nsac 0
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00408000
mmc0: req done (CMD51): 0: 00000920 00000000 00000000 00000000
mmc0: 0 bytes transferred: -84
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc0: error -84 whilst initialising SD card
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
