This adds support for an 8bit wide bus to the card (data lines MCIDAT0 through 7 exist) on the ST Micro version and alters the U300 platform to support this. Also add some ST_ prefix to the ST-specific registers. Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxxxxxx> --- arch/arm/mach-u300/mmc.c | 2 +- drivers/mmc/host/mmci.c | 6 ++++-- drivers/mmc/host/mmci.h | 6 ++++-- 3 files changed, 9 insertions(+), 5 deletions(-) diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c index 77fbb1e..c2549b8 100644 --- a/arch/arm/mach-u300/mmc.c +++ b/arch/arm/mach-u300/mmc.c @@ -106,7 +106,7 @@ int __devinit mmc_init(struct amba_device *adev) mmci_card->mmc0_plat_data.gpio_wp = -1; mmci_card->mmc0_plat_data.gpio_cd = -1; mmci_card->mmc0_plat_data.capabilities = MMC_CAP_MMC_HIGHSPEED | - MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA; + MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA; mmcsd_device->platform_data = (void *) &mmci_card->mmc0_plat_data; diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index 84c103a..7e70c1a 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -55,14 +55,16 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired) host->cclk = host->mclk / (2 * (clk + 1)); } if (host->hw_designer == AMBA_VENDOR_ST) - clk |= MCI_FCEN; /* Bug fix in ST IP block */ + clk |= MCI_ST_FCEN; /* Bug fix in ST IP block */ clk |= MCI_CLK_ENABLE; /* This hasn't proven to be worthwhile */ /* clk |= MCI_CLK_PWRSAVE; */ } if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) - clk |= MCI_WIDE_BUS; + clk |= MCI_4BIT_BUS; + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) + clk |= MCI_ST_8BIT_BUS; writel(clk, host->base + MMCICLOCK); } diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h index 1ceb9a9..d77062e 100644 --- a/drivers/mmc/host/mmci.h +++ b/drivers/mmc/host/mmci.h @@ -25,9 +25,11 @@ #define MCI_CLK_ENABLE (1 << 8) #define MCI_CLK_PWRSAVE (1 << 9) #define MCI_CLK_BYPASS (1 << 10) -#define MCI_WIDE_BUS (1 << 11) +#define MCI_4BIT_BUS (1 << 11) +/* 8bit wide buses supported in ST Micro versions */ +#define MCI_ST_8BIT_BUS (1 << 12) /* HW flow control on the ST Micro version */ -#define MCI_FCEN (1 << 13) +#define MCI_ST_FCEN (1 << 13) #define MMCIARGUMENT 0x008 #define MMCICOMMAND 0x00c -- 1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
