This enables the use of a regulator to power the MMCI/PL180
PrimeCell. The OCR mask is calculated and voltage is set using
the new MMC core functions for discovering voltage ranges
in regulators. The platform translate_vdd function which basically
controls the 4 lines out of the PL180 is disabled if you use a
regulator instead.
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxxxxxx>
---
drivers/mmc/host/mmci.c | 50 +++++++++++++++++++++++++++++++++++++++++++---
drivers/mmc/host/mmci.h | 1 +
2 files changed, 47 insertions(+), 4 deletions(-)
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 79205e5..3d1e532 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -23,6 +23,7 @@
#include <linux/scatterlist.h>
#include <linux/gpio.h>
#include <linux/amba/mmci.h>
+#include <linux/regulator/consumer.h>
#include <asm/cacheflush.h>
#include <asm/div64.h>
@@ -452,13 +453,28 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
u32 pwr = 0;
unsigned long flags;
- if (host->plat->translate_vdd)
- pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
-
switch (ios->power_mode) {
case MMC_POWER_OFF:
+ if(host->vcc &&
+ regulator_is_enabled(host->vcc))
+ regulator_disable(host->vcc);
break;
case MMC_POWER_UP:
+#ifdef CONFIG_REGULATOR
+ if (host->vcc)
+ /* This implicitly enables the regulator */
+ mmc_regulator_set_ocr(host->vcc, ios->vdd);
+#endif
+ /*
+ * The translate_vdd function is not used if you have
+ * an external regulator, or your design is really weird.
+ * Using it would mean sending in power control BOTH using
+ * a regulator AND the 4 MMCIPWR bits. If we don't have
+ * a regulator, we might have some other platform specific
+ * power control behind this translate function.
+ */
+ if (!host->vcc && host->plat->translate_vdd)
+ pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
/* The ST version does not have this, fall through to POWER_ON */
if (host->hw_designer != AMBA_VENDOR_ST) {
pwr |= MCI_PWR_UP;
@@ -603,7 +619,29 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
mmc->ops = &mmci_ops;
mmc->f_min = (host->mclk + 511) / 512;
mmc->f_max = min(host->mclk, fmax);
- mmc->ocr_avail = plat->ocr_mask;
+#ifdef CONFIG_REGULATOR
+ /* If we're using the regulator framework, try to fetch a regulator */
+ host->vcc = regulator_get(&dev->dev, "vmmc");
+ if (IS_ERR(host->vcc))
+ host->vcc = NULL;
+ else {
+ int mask = mmc_regulator_get_ocrmask(host->vcc);
+
+ if (mask < 0)
+ dev_err(&dev->dev, "error getting OCR mask (%d)\n",
+ mask);
+ else {
+ host->mmc->ocr_avail = (u32) mask;
+ if (plat->ocr_mask)
+ dev_warn(&dev->dev,
+ "Provided ocr_mask/setpower will not be used "
+ "(using regulator instead)\n");
+ }
+ }
+#endif
+ /* Fall back to platform data if no regulator is found */
+ if (host->vcc == NULL)
+ mmc->ocr_avail = plat->ocr_mask;
mmc->caps = plat->capabilities;
/*
@@ -741,6 +779,10 @@ static int __devexit mmci_remove(struct amba_device *dev)
clk_disable(host->clk);
clk_put(host->clk);
+ if (regulator_is_enabled(host->vcc))
+ regulator_disable(host->vcc);
+ regulator_put(host->vcc);
+
mmc_free_host(mmc);
amba_release_regions(dev);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index a7f9a51..1ceb9a9 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -175,6 +175,7 @@ struct mmci_host {
struct scatterlist *sg_ptr;
unsigned int sg_off;
unsigned int size;
+ struct regulator *vcc;
};
static inline void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
--
1.6.2.1
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
