This patch introduces a new boot option "movablenodes". This parameter
depends on movable_node, it is used for debugging memory hotplug.
Instead SRAT specifies which memory is hotpluggable.
e.g. movable_node movablenodes=1,2,4
It means nodes 1,2,4 will be set to movable nodes, the other nodes are
unmovable nodes. Usually movable nodes are parsed from SRAT table which
offered by BIOS.
Signed-off-by: Xishi Qiu <qiuxishi@xxxxxxxxxx>
---
Documentation/kernel-parameters.txt | 5 ++++
arch/x86/mm/srat.c | 36 +++++++++++++++++++++++++++++++++++
2 files changed, 41 insertions(+), 0 deletions(-)
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 5ae8608..e072ccf 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1949,6 +1949,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
movable_node [KNL,X86] Boot-time switch to enable the effects
of CONFIG_MOVABLE_NODE=y. See mm/Kconfig for details.
+ movablenodes= [KNL,X86] This parameter depends on movable_node, it
+ is used for debugging memory hotplug. Instead SRAT
+ specifies which memory is hotpluggable.
+ e.g. movablenodes=1,2,4
+
MTD_Partition= [MTD]
Format: <name>,<region-number>,<size>,<offset>
diff --git a/arch/x86/mm/srat.c b/arch/x86/mm/srat.c
index 66338a6..523e58b 100644
--- a/arch/x86/mm/srat.c
+++ b/arch/x86/mm/srat.c
@@ -157,6 +157,37 @@ static inline int save_add_info(void) {return 1;}
static inline int save_add_info(void) {return 0;}
#endif
+static nodemask_t movablenodes_mask;
+
+static void __init parse_movablenodes_one(char *p)
+{
+ int node;
+
+ get_option(&p, &node);
+ node_set(node, movablenodes_mask);
+}
+
+static int __init parse_movablenodes_opt(char *str)
+{
+ nodes_clear(movablenodes_mask);
+
+#ifdef CONFIG_MOVABLE_NODE
+ while (str) {
+ char *k = strchr(str, ',');
+
+ if (k)
+ *k++ = 0;
+ parse_movablenodes_one(str);
+ str = k;
+ }
+#else
+ pr_warn("movable_node option not supported\n");
+#endif
+
+ return 0;
+}
+early_param("movablenodes", parse_movablenodes_opt);
+
/* Callback for parsing of the Proximity Domain <-> Memory Area mappings */
int __init
acpi_numa_memory_affinity_init(struct acpi_srat_mem_affinity *ma)
@@ -202,6 +233,11 @@ acpi_numa_memory_affinity_init(struct acpi_srat_mem_affinity *ma)
pr_warn("SRAT: Failed to mark hotplug range [mem %#010Lx-%#010Lx] in memblock\n",
(unsigned long long)start, (unsigned long long)end - 1);
+ if (node_isset(node, movablenodes_mask) &&
+ memblock_mark_hotplug(start, ma->length))
+ pr_warn("SRAT debug: Failed to mark hotplug range [mem %#010Lx-%#010Lx] in memblock\n",
+ (unsigned long long)start, (unsigned long long)end - 1);
+
return 0;
out_err_bad_srat:
bad_srat();
--
1.7.1
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxx. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>