This patch adds the documentation file for the zswap functionality Signed-off-by: Seth Jennings <sjenning@xxxxxxxxxxxxxxxxxx> --- Documentation/vm/zswap.txt | 72 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 72 insertions(+) create mode 100644 Documentation/vm/zswap.txt diff --git a/Documentation/vm/zswap.txt b/Documentation/vm/zswap.txt new file mode 100644 index 0000000..88384b3 --- /dev/null +++ b/Documentation/vm/zswap.txt @@ -0,0 +1,72 @@ +Overview: + +Zswap is a lightweight compressed cache for swap pages. It takes pages that are +in the process of being swapped out and attempts to compress them into a +dynamically allocated RAM-based memory pool. If this process is successful, +the writeback to the swap device is deferred and, in many cases, avoided +completely. This results in a significant I/O reduction and performance gains +for systems that are swapping. + +Zswap provides compressed swap caching that basically trades CPU cycles for +reduced swap I/O. This trade-off can result in a significant performance +improvement as reads to/writes from to the compressed cache almost always +faster that reading from a swap device which incurs the latency of an +asynchronous block I/O read. + +Some potential benefits: +* Desktop/laptop users with limited RAM capacities can mitigate the + performance impact of swapping. +* Overcommitted guests that share a common I/O resource can + dramatically reduce their swap I/O pressure, avoiding heavy handed I/O + throttling by the hypervisor. This allows more work to get done with less + impact to the guest workload and guests sharing the I/O subsystem +* Users with SSDs as swap devices can extend the life of the device by + drastically reducing life-shortening writes. + +Zswap evicts pages from compressed cache on an LRU basis to the backing swap +device when the compressed pool reaches it size limit. This requirement had +been identified in prior community discussions. + +To enabled zswap, the "enabled" attribute must be set to 1 at boot time. e.g. +zswap.enabled=1 + +Design: + +Zswap receives pages for compression through the Frontswap API and is able to +evict pages from its own compressed pool on an LRU basis and write them back to +the backing swap device in the case that the compressed pool is full. + +Zswap makes use of zbud for the managing the compressed memory pool. Each +allocation in zbud is not directly accessible by address. Rather, a handle is +return by the allocation routine and that handle must be mapped before being +accessed. The compressed memory pool grows on demand and shrinks as compressed +pages are freed. The pool is not preallocated. + +When a swap page is passed from frontswap to zswap, zswap maintains a mapping +of the swap entry, a combination of the swap type and swap offset, to the zbud +handle that references that compressed swap page. This mapping is achieved +with a red-black tree per swap type. The swap offset is the search key for the +tree nodes. + +During a page fault on a PTE that is a swap entry, frontswap calls the zswap +load function to decompress the page into the page allocated by the page fault +handler. + +Once there are no PTEs referencing a swap page stored in zswap (i.e. the count +in the swap_map goes to 0) the swap code calls the zswap invalidate function, +via frontswap, to free the compressed entry. + +Zswap seeks to be simple in its policies. Sysfs attributes allow for two user +controlled policies: +* max_compression_ratio - Maximum compression ratio, as as percentage, + for an acceptable compressed page. Any page that does not compress by at + least this ratio will be rejected. +* max_pool_percent - The maximum percentage of memory that the compressed + pool can occupy. + +Zswap allows the compressor to be selected at kernel boot time by setting the +“compressor” attribute. The default compressor is lzo. e.g. +zswap.compressor=deflate + +A debugfs interface is provided for various statistic about pool size, number +of pages stored, and various counters for the reasons pages are rejected. -- 1.7.9.5 -- To unsubscribe, send a message with 'unsubscribe linux-mm' in the body to majordomo@xxxxxxxxx. For more info on Linux MM, see: http://www.linux-mm.org/ . Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>