Re: [PATCH] fadvise: perform WILLNEED readahead in a workqueue

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Dec 16, 2012 at 03:59:53AM +0000, Eric Wong wrote:
> Dave Chinner <david@xxxxxxxxxxxxx> wrote:
> > On Sun, Dec 16, 2012 at 03:04:42AM +0000, Eric Wong wrote:
> > > Dave Chinner <david@xxxxxxxxxxxxx> wrote:
> > > > On Sat, Dec 15, 2012 at 12:54:48AM +0000, Eric Wong wrote:
> > > > > 
> > > > >  Before: fadvise64(3, 0, 0, POSIX_FADV_WILLNEED) = 0 <2.484832>
> > > > >   After: fadvise64(3, 0, 0, POSIX_FADV_WILLNEED) = 0 <0.000061>
> > > > 
> > > > You've basically asked fadvise() to readahead the entire file if it
> > > > can. That means it is likely to issue enough readahead to fill the
> > > > IO queue, and that's where all the latency is coming from. If all
> > > > you are trying to do is reduce the latency of the first read, then
> > > > only readahead the initial range that you are going to need to read...
> > > 
> > > Yes, I do want to read the whole file, eventually.  So I want to put
> > > the file into the page cache ASAP and allow the disk to spin down.
> > 
> > Issuing readahead is not going to speed up the first read. Either
> > you will spend more time issuing all the readahead, or you block
> > waiting for the first read to complete. And the way you are issuing
> > readahead does not guarantee the entire file is brought into the
> > page cache....
> 
> I'm not relying on readahead to speed up the first read.
> 
> By using fadvise/readahead, I want a _best-effort_ attempt to
> keep the file in cache.
> 
> > > But I also want the first read() to be fast.
> > 
> > You can't have a pony, sorry.
> 
> I want the first read() to happen sooner than it would under current
> fadvise. 

You're not listening.  You do not need the kernel to be modified to
avoid the latency of issuing 1GB of readahead on a file.

You don't need to do readahead before the first read. Nor do you do
need to wait for 1GB of readhead to be issued before you do the
first read.

You could do readahead *concurrently* with the first read, so the
first read only blocks until the readahead of the first part of the
file completes.  i.e. just do readahead() in a background thread and
don't wait for it to complete before doing the first read.

You could even do readahead *after* the first read, when the time it
takes *doesn't matter* to the processing of the incoming data...

> I want "less-bad" initial latency than I was getting.

And you can do that by changing how you issue readahead from
userspace.

Cheers,

Dave.
-- 
Dave Chinner
david@xxxxxxxxxxxxx

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxx.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>


[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Bugtraq]     [Linux]     [Linux OMAP]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]