Make CONFIG_SLAB_MERGE_DEFAULT default to n unless CONFIG_SLUB_TINY is
enabled. Benefits of slab merging is limited on systems that are not
memory constrained: the overhead is negligible and evidence of its
effect on cache hotness is hard to come by.
On the other hand, distinguishing allocations into different slabs will
make attacks that rely on "heap spraying" more difficult to carry out
with success.
Take sides with security in the default kernel configuration over
questionnable performance benefits/memory efficiency.
Signed-off-by: Julian Pidancet <julian.pidancet@xxxxxxxxxx>
---
In an attempt to assess the performance impact of disabling slab
merging, a timed linux kernel compilation test has been conducted first
using slab_merge, then using slab_nomerge. Both tests started in an
identical state. Commodity hardware was used: a laptop with an AMD Ryzen
5 3500U CPU, and 16GiB of RAM. The kernel source files were placed on
an XFS partition because of the extensive use of slab caches in XFS.
The results are as follows:
| slab_merge | slab_nomerge |
------+------------------+------------------|
Time | 489.074 ± 10.334 | 489.975 ± 10.350 |
Min | 459.688 | 460.554 |
Max | 493.126 | 494.282 |
The benchmark favors the configuration where merging is disabled, but the
difference is only ~0.18%, well under statistical significance.
.../admin-guide/kernel-parameters.txt | 29 ++++++++++---------
Documentation/mm/slub.rst | 5 ++--
mm/Kconfig | 6 ++--
3 files changed, 21 insertions(+), 19 deletions(-)
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 9e5bab29685f..5fbf6ed3c62e 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -5652,21 +5652,22 @@
slram= [HW,MTD]
- slab_merge [MM]
- Enable merging of slabs with similar size when the
- kernel is built without CONFIG_SLAB_MERGE_DEFAULT.
-
slab_nomerge [MM]
- Disable merging of slabs with similar size. May be
- necessary if there is some reason to distinguish
- allocs to different slabs, especially in hardened
- environments where the risk of heap overflows and
- layout control by attackers can usually be
- frustrated by disabling merging. This will reduce
- most of the exposure of a heap attack to a single
- cache (risks via metadata attacks are mostly
- unchanged). Debug options disable merging on their
- own.
+ Disable merging of slabs with similar size when
+ the kernel is built with CONFIG_SLAB_MERGE_DEFAULT.
+ Allocations of the same size made in distinct
+ caches will be placed in separate slabs. In
+ hardened environment, the risk of heap overflows
+ and layout control by attackers can usually be
+ frustrated by disabling merging.
+
+ slab_merge [MM]
+ Enable merging of slabs with similar size. May be
+ necessary to reduce overhead or increase cache
+ hotness of objects, at the cost of increased
+ exposure in case of a heap attack to a single
+ cache. (risks via metadata attacks are mostly
+ unchanged).
For more information see Documentation/mm/slub.rst.
slab_max_order= [MM, SLAB]
diff --git a/Documentation/mm/slub.rst b/Documentation/mm/slub.rst
index be75971532f5..e2549f4a98dd 100644
--- a/Documentation/mm/slub.rst
+++ b/Documentation/mm/slub.rst
@@ -122,8 +122,9 @@ used on the wrong slab.
Slab merging
============
-If no debug options are specified then SLUB may merge similar slabs together
-in order to reduce overhead and increase cache hotness of objects.
+If the kernel is built with ``CONFIG_SLAB_MEGE_DEFAULT`` or if ``slab_merge``
+is specified on the kernel command line, then SLUB may merge similar slabs
+together in order to reduce overhead and increase cache hotness of objects.
``slabinfo -a`` displays which slabs were merged together.
Slab validation
diff --git a/mm/Kconfig b/mm/Kconfig
index 7672a22647b4..05b0304302d4 100644
--- a/mm/Kconfig
+++ b/mm/Kconfig
@@ -255,7 +255,7 @@ config SLUB_TINY
config SLAB_MERGE_DEFAULT
bool "Allow slab caches to be merged"
- default y
+ default n
depends on SLAB || SLUB
help
For reduced kernel memory fragmentation, slab caches can be
@@ -264,8 +264,8 @@ config SLAB_MERGE_DEFAULT
overwrite objects from merged caches (and more easily control
cache layout), which makes such heap attacks easier to exploit
by attackers. By keeping caches unmerged, these kinds of exploits
- can usually only damage objects in the same cache. To disable
- merging at runtime, "slab_nomerge" can be passed on the kernel
+ can usually only damage objects in the same cache. To enable
+ merging at runtime, "slab_merge" can be passed on the kernel
command line.
config SLAB_FREELIST_RANDOM
--
2.40.1
