On Mon, 2023-02-13 at 14:39 -0800, Dave Hansen wrote:
> On 2/13/23 03:59, Kai Huang wrote:
> > SEAMCALL instruction causes #GP when TDX isn't BIOS enabled, and #UD
> > when CPU is not in VMX operation. The current TDX_MODULE_CALL macro
> > doesn't handle any of them. There's no way to check whether the CPU is
> > in VMX operation or not.
>
> Really? ... *REALLY*?
>
> Like, there's no possible way for the kernel to record whether it has
> executed VMXON or not?
>
> I think what you're saying here is that there's no architecturally
> visible flag that tells you whether in spot #1 or #2 in the following code:
>
> static int kvm_cpu_vmxon(u64 vmxon_pointer)
> {
> u64 msr;
>
> cr4_set_bits(X86_CR4_VMXE);
> // spot #1
> asm_volatile_goto("1: vmxon %[vmxon_pointer]\n\t"
> _ASM_EXTABLE(1b, %l[fault])
> : : [vmxon_pointer] "m"(vmxon_pointer)
> : : fault);
> // spot #2
>
Yes I was talking about architectural flag rather than kernel defined software
tracking mechanism.
> That's _maybe_ technically correct (I don't know enough about VMX
> enabling to tell you). But, what I *DO* know is that it's nonsense to
> say that it's impossible in the *kernel* to tell whether we're on a CPU
> that's successfully executed VMXON or not.
>
> kvm_cpu_vmxon() has two paths through it:
>
> 1. Successfully executes VMXON and leaves with X86_CR4_VMXE=1
> 2. Fails VMXON and leaves with X86_CR4_VMXE=0
>
> Guess what? CR4 is rather architecturally visible. From what I can
> tell, it's *ENTIRELY* plausible to assume that X86_CR4_VMXE==1 means
> that VMXON has been done.
>
Yes CR4.VMXE bit can be used to check. This is what KVM does.
Architecturally CR4.VMXE bit only checks whether VMX is enabled, but not VMXON
has been done, but in current kernel implement they are always done together.
So checking CR4 is fine.
> Even if that's wrong, it's only a cpumask and
> a cpumask_set() away from becoming plausible. Like so:
>
> static int kvm_cpu_vmxon(u64 vmxon_pointer)
> {
> u64 msr;
>
> cr4_set_bits(X86_CR4_VMXE);
>
> asm_volatile_goto("1: vmxon %[vmxon_pointer]\n\t"
> _ASM_EXTABLE(1b, %l[fault])
> : : [vmxon_pointer] "m"(vmxon_pointer)
> : : fault);
> // set cpumask bit here
> return 0;
>
> fault:
> // clear cpu bit here
> cr4_clear_bits(X86_CR4_VMXE);
>
> return -EFAULT;
> }
>
> How many design decisions down the line in this series were predicated
> on the idea that:
>
> There's no way to check whether the CPU is
> in VMX operation or not.
>
> ?
Only the assembly code to handle TDX_SEAMCALL_UD in this patch is.
Whether we have definitive way to _check_ whether VMXON has been done doesn't
matter. What impacts the design decisions is (non-KVM) kernel doesn't support
doing VMXON and we depend on KVM to do that (which is also a design decision).
We can remove the assembly code which returns TDX_SEAMCALL_{UD|GP} and replace
it with a below check in seamcall():
static int seamcall(...)
{
cpu = get_cpu();
if (cr4_read_shadow() & X86_CR4_VMXE) {
WARN_ONCE("VMXON isn't done for cpu ...\n");
ret = -EINVAL;
}
...
out:
put_cpu();
return ret;
}
But this was actually discussed in the v5, in which IIUC you prefer to having
the assembly code to return additional TDX_SEAMCALL_UD rather than having above
CR4 check:
https://lore.kernel.org/all/77c90075-79d4-7cc7-f266-1b67e586513b@xxxxxxxxx/
