Re: [PATCH 00/21] mm: introduce Designated Movable Blocks

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Dough,

I have some high-level questions.

MOTIVATION:
Some Broadcom devices (e.g. 7445, 7278) contain multiple memory
controllers with each mapped in a different address range within
a Uniform Memory Architecture. Some users of these systems have

How large are these areas typically?

How large are they in comparison to other memory in the system?

How is this memory currently presented to the system?

expressed the desire to locate ZONE_MOVABLE memory on each
memory controller to allow user space intensive processing to
make better use of the additional memory bandwidth.

Can you share some more how exactly ZONE_MOVABLE would help here to make better use of the memory bandwidth?

Unfortunately, the historical monotonic layout of zones would
mean that if the lowest addressed memory controller contains
ZONE_MOVABLE memory then all of the memory available from
memory controllers at higher addresses must also be in the
ZONE_MOVABLE zone. This would force all kernel memory accesses
onto the lowest addressed memory controller and significantly
reduce the amount of memory available for non-movable
allocations.

We do have code that relies on zones during boot to not overlap within a single node.


The main objective of this patch set is therefore to allow a
block of memory to be designated as part of the ZONE_MOVABLE
zone where it will always only be used by the kernel page
allocator to satisfy requests for movable pages. The term
Designated Movable Block is introduced here to represent such a
block. The favored implementation allows modification of the

Sorry to say, but that term is rather suboptimal to describe what you are doing here. You simply have some system RAM you'd want to have managed by ZONE_MOVABLE, no?

'movablecore' kernel parameter to allow specification of a base
address and support for multiple blocks. The existing
'movablecore' mechanisms are retained. Other mechanisms based on
device tree are also included in this set.

BACKGROUND:
NUMA architectures support distributing movablecore memory
across each node, but it is undesirable to introduce the
overhead and complexities of NUMA on systems that don't have a
Non-Uniform Memory Architecture.

How exactly would that look like? I think I am missing something :)


Commit 342332e6a925 ("mm/page_alloc.c: introduce kernelcore=mirror option")
also depends on zone overlap to support sytems with multiple
mirrored ranges.

IIRC, zones will not overlap within a single node.


Commit c6f03e2903c9 ("mm, memory_hotplug: remove zone restrictions")
embraced overlapped zones for memory hotplug.

Yes, after boot.


This commit set follows their lead to allow the ZONE_MOVABLE
zone to overlap other zones while spanning the pages from the
lowest Designated Movable Block to the end of the node.
Designated Movable Blocks are made absent from overlapping zones
and present within the ZONE_MOVABLE zone.

I initially investigated an implementation using a Designated
Movable migrate type in line with comments[1] made by Mel Gorman
regarding a "sticky" MIGRATE_MOVABLE type to avoid using
ZONE_MOVABLE. However, this approach was riskier since it was
much more instrusive on the allocation paths. Ultimately, the
progress made by the memory hotplug folks to expand the
ZONE_MOVABLE functionality convinced me to follow this approach.

OPPORTUNITIES:
There have been many attempts to modify the behavior of the
kernel page allocators use of CMA regions. This implementation
of Designated Movable Blocks creates an opportunity to repurpose
the CMA allocator to operate on ZONE_MOVABLE memory that the
kernel page allocator can use more agressively, without
affecting the existing CMA implementation. It is hoped that the
"shared-dmb-pool" approach included here will be useful in cases
where memory sharing is more important than allocation latency.

CMA introduced a paradigm where multiple allocators could
operate on the same region of memory, and that paradigm can be
extended to Designated Movable Blocks as well. I was interested
in using kernel resource management as a mechanism for exposing
Designated Movable Block resources (e.g. /proc/iomem) that would
be used by the kernel page allocator like any other ZONE_MOVABLE
memory, but could be claimed by an alternative allocator (e.g.
CMA). Unfortunately, this becomes complicated because the kernel
resource implementation varies materially across different
architectures and I do not require this capability so I have
deferred that.

Why can't we simply designate these regions as CMA regions?

Why do we have to start using ZONE_MOVABLE for them?

--
Thanks,

David / dhildenb





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [eCos]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux