On Mon, Apr 4, 2022 at 5:32 PM Michal Hocko <mhocko@xxxxxxxx> wrote:
>
> On Mon 04-04-22 17:23:43, Zhaoyang Huang wrote:
> > On Mon, Apr 4, 2022 at 5:07 PM Zhaoyang Huang <huangzhaoyang@xxxxxxxxx> wrote:
> > >
> > > On Mon, Apr 4, 2022 at 4:51 PM Michal Hocko <mhocko@xxxxxxxx> wrote:
> > > >
> > > > On Mon 04-04-22 10:33:58, Zhaoyang Huang wrote:
> > > > [...]
> > > > > > One thing that I don't understand in this approach is: why memory.low
> > > > > > should depend on the system's memory pressure. It seems you want to
> > > > > > allow a process to allocate more when memory pressure is high. That is
> > > > > > very counter-intuitive to me. Could you please explain the underlying
> > > > > > logic of why this is the right thing to do, without going into
> > > > > > technical details?
> > > > > What I want to achieve is make memory.low be positive correlation with
> > > > > timing and negative to memory pressure, which means the protected
> > > > > memcg should lower its protection(via lower memcg.low) for helping
> > > > > system's memory pressure when it's high.
> > > >
> > > > I have to say this is still very confusing to me. The low limit is a
> > > > protection against external (e.g. global) memory pressure. Decreasing
> > > > the protection based on the external pressure sounds like it goes right
> > > > against the purpose of the knob. I can see reasons to update protection
> > > > based on refaults or other metrics from the userspace but I still do not
> > > > see how this is a good auto-magic tuning done by the kernel.
> > > >
> > > > > The concept behind is memcg's
> > > > > fault back of dropped memory is less important than system's latency
> > > > > on high memory pressure.
> > > >
> > > > Can you give some specific examples?
> > > For both of the above two comments, please refer to the latest test
> > > result in Patchv2 I have sent. I prefer to name my change as focus
> > > transfer under pressure as protected memcg is the focus when system's
> > > memory pressure is low which will reclaim from root, this is not
> > > against current design. However, when global memory pressure is high,
> > > then the focus has to be changed to the whole system, because it
> > > doesn't make sense to let the protected memcg out of everybody, it
> > > can't
> > > do anything when the system is trapped in the kernel with reclaiming work.
> > Does it make more sense if I describe the change as memcg will be
> > protect long as system pressure is under the threshold(partially
> > coherent with current design) and will sacrifice the memcg if pressure
> > is over the threshold(added change)
>
> No, not really. For one it is still really unclear why there should be any
> difference in the semantic between global and external memory pressure
> in general. The low limit is always a protection from the external
> pressure. And what should be the actual threshold? Amount of the reclaim
> performed, effectivness of the reclaim or what?
Please find bellowing for the test result, which shows current design
has more effective protection when system memory pressure is high. It
could be argued that the protected memcg lost the protection as its
usage dropped too much. I would like to say that this is just the goal
of the change. Is it reasonable to let the whole system be trapped in
memory pressure while the memcg holds the memory? With regard to
threshold, it is a dynamic decayed watermark value which represents
the historic(watermark) and present(update to new usage if it expands
again) usage. Actually, I have update the code by adding opt-in code
which means this is a opt type of the memcg. This patch is coherent to
the original design if user want to set the fixed value by default and
also provide a new way of dynamic protected memcg without external
monitor and interactivation.
We simply test above change by comparing it with current design on a v5.4 based
system in 3GB RAM in bellowing steps, via which we can find that fixed
memory.low have the system experience high memory pressure with holding too
much memory.
1. setting up the topology seperatly as [1]
2. place a memory cost process into B and have it consume 1GB memory
from userspace.
3. generating global memory pressure via mlock 1GB memory.
4. watching B's memory.current and PSI_MEM.
5. repeat 3,4 twice.
[1]. setting fixed low=500MB; low=600MB; wm_decay_factor=36(68s decay 1/2)
A(low=500MB)
/
B(low=500MB)
What we observed are:
PSI_MEM, usage PSI_MEM,usage
PSI_MEM,usage
(Mlock 1GB) (Mlock 2GB)
(stable)
low=600MB s=23 f=17 u=720/600MB s=91 f=48 u=202MB s=68 f=32 u=106MB
low=500MB s=22 f=13 u=660/530MB s=88 f=50 u=156MB s=30 f=20 u=120MB
patch s=23 f=12 u=692/470MB s=40 f=23 u=67MB s=21 f=18 u=45MB
> --
> Michal Hocko
> SUSE Labs
