From: Vlastimil Babka <vbabka@xxxxxxx> Subject: mm, slub: simplify kmem_cache_cpu and tid setup In slab_alloc_node() and do_slab_free() fastpaths we need to guarantee that our kmem_cache_cpu pointer is from the same cpu as the tid value. Currently that's done by reading the tid first using this_cpu_read(), then the kmem_cache_cpu pointer and verifying we read the same tid using the pointer and plain READ_ONCE(). This can be simplified to just fetching kmem_cache_cpu pointer and then reading tid using the pointer. That guarantees they are from the same cpu. We don't need to read the tid using this_cpu_read() because the value will be validated by this_cpu_cmpxchg_double(), making sure we are on the correct cpu and the freelist didn't change by anyone preempting us since reading the tid. Link: https://lkml.kernel.org/r/20210904105003.11688-11-vbabka@xxxxxxx Signed-off-by: Vlastimil Babka <vbabka@xxxxxxx> Acked-by: Mel Gorman <mgorman@xxxxxxxxxxxxxxxxxxx> Cc: Christoph Lameter <cl@xxxxxxxxx> Cc: David Rientjes <rientjes@xxxxxxxxxx> Cc: Jann Horn <jannh@xxxxxxxxxx> Cc: Jesper Dangaard Brouer <brouer@xxxxxxxxxx> Cc: Joonsoo Kim <iamjoonsoo.kim@xxxxxxx> Cc: Mike Galbraith <efault@xxxxxx> Cc: Pekka Enberg <penberg@xxxxxxxxxx> Cc: Qian Cai <quic_qiancai@xxxxxxxxxxx> Cc: Sebastian Andrzej Siewior <bigeasy@xxxxxxxxxxxxx> Cc: Thomas Gleixner <tglx@xxxxxxxxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- mm/slub.c | 22 +++++++++------------- 1 file changed, 9 insertions(+), 13 deletions(-) --- a/mm/slub.c~mm-slub-simplify-kmem_cache_cpu-and-tid-setup +++ a/mm/slub.c @@ -2882,15 +2882,14 @@ redo: * reading from one cpu area. That does not matter as long * as we end up on the original cpu again when doing the cmpxchg. * - * We should guarantee that tid and kmem_cache are retrieved on - * the same cpu. It could be different if CONFIG_PREEMPTION so we need - * to check if it is matched or not. + * We must guarantee that tid and kmem_cache_cpu are retrieved on the + * same cpu. We read first the kmem_cache_cpu pointer and use it to read + * the tid. If we are preempted and switched to another cpu between the + * two reads, it's OK as the two are still associated with the same cpu + * and cmpxchg later will validate the cpu. */ - do { - tid = this_cpu_read(s->cpu_slab->tid); - c = raw_cpu_ptr(s->cpu_slab); - } while (IS_ENABLED(CONFIG_PREEMPTION) && - unlikely(tid != READ_ONCE(c->tid))); + c = raw_cpu_ptr(s->cpu_slab); + tid = READ_ONCE(c->tid); /* * Irqless object alloc/free algorithm used here depends on sequence @@ -3164,11 +3163,8 @@ redo: * data is retrieved via this pointer. If we are on the same cpu * during the cmpxchg then the free will succeed. */ - do { - tid = this_cpu_read(s->cpu_slab->tid); - c = raw_cpu_ptr(s->cpu_slab); - } while (IS_ENABLED(CONFIG_PREEMPTION) && - unlikely(tid != READ_ONCE(c->tid))); + c = raw_cpu_ptr(s->cpu_slab); + tid = READ_ONCE(c->tid); /* Same with comment on barrier() in slab_alloc_node() */ barrier(); _
