From: "Uladzislau Rezki (Sony)" <urezki@xxxxxxxxx> Subject: vm/test_vmalloc.sh: adapt for updated driver interface A 'single_cpu_test' parameter is odd and it does not exist anymore. Instead there was introduced a 'nr_threads' one. If it is not set it behaves as the former parameter. That is why update a "stress mode" according to this change specifying number of workers which are equal to number of CPUs. Also update an output of help message based on a new interface. Link: https://lkml.kernel.org/r/20210402202237.20334-3-urezki@xxxxxxxxx Signed-off-by: Uladzislau Rezki (Sony) <urezki@xxxxxxxxx> Cc: Shuah Khan <shuah@xxxxxxxxxx> Cc: Hillf Danton <hdanton@xxxxxxxx> Cc: Matthew Wilcox <willy@xxxxxxxxxxxxx> Cc: Michal Hocko <mhocko@xxxxxxxx> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@xxxxxxxxxxxxxx> Cc: Steven Rostedt <rostedt@xxxxxxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- tools/testing/selftests/vm/test_vmalloc.sh | 21 +++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-) --- a/tools/testing/selftests/vm/test_vmalloc.sh~vm-test_vmallocsh-adapt-for-updated-driver-interface +++ a/tools/testing/selftests/vm/test_vmalloc.sh @@ -11,6 +11,7 @@ TEST_NAME="vmalloc" DRIVER="test_${TEST_NAME}" +NUM_CPUS=`grep -c ^processor /proc/cpuinfo` # 1 if fails exitcode=1 @@ -22,9 +23,9 @@ ksft_skip=4 # Static templates for performance, stressing and smoke tests. # Also it is possible to pass any supported parameters manualy. # -PERF_PARAM="single_cpu_test=1 sequential_test_order=1 test_repeat_count=3" -SMOKE_PARAM="single_cpu_test=1 test_loop_count=10000 test_repeat_count=10" -STRESS_PARAM="test_repeat_count=20" +PERF_PARAM="sequential_test_order=1 test_repeat_count=3" +SMOKE_PARAM="test_loop_count=10000 test_repeat_count=10" +STRESS_PARAM="nr_threads=$NUM_CPUS test_repeat_count=20" check_test_requirements() { @@ -58,8 +59,8 @@ run_perfformance_check() run_stability_check() { - echo "Run stability tests. In order to stress vmalloc subsystem we run" - echo "all available test cases on all available CPUs simultaneously." + echo "Run stability tests. In order to stress vmalloc subsystem all" + echo "available test cases are run by NUM_CPUS workers simultaneously." echo "It will take time, so be patient." modprobe $DRIVER $STRESS_PARAM > /dev/null 2>&1 @@ -92,17 +93,17 @@ usage() echo "# Shows help message" echo "./${DRIVER}.sh" echo - echo "# Runs 1 test(id_1), repeats it 5 times on all online CPUs" - echo "./${DRIVER}.sh run_test_mask=1 test_repeat_count=5" + echo "# Runs 1 test(id_1), repeats it 5 times by NUM_CPUS workers" + echo "./${DRIVER}.sh nr_threads=$NUM_CPUS run_test_mask=1 test_repeat_count=5" echo echo -n "# Runs 4 tests(id_1|id_2|id_4|id_16) on one CPU with " echo "sequential order" - echo -n "./${DRIVER}.sh single_cpu_test=1 sequential_test_order=1 " + echo -n "./${DRIVER}.sh sequential_test_order=1 " echo "run_test_mask=23" echo - echo -n "# Runs all tests on all online CPUs, shuffled order, repeats " + echo -n "# Runs all tests by NUM_CPUS workers, shuffled order, repeats " echo "20 times" - echo "./${DRIVER}.sh test_repeat_count=20" + echo "./${DRIVER}.sh nr_threads=$NUM_CPUS test_repeat_count=20" echo echo "# Performance analysis" echo "./${DRIVER}.sh performance" _
