On 3/24/21 1:41 PM, Jason Gunthorpe wrote:
On Wed, Mar 24, 2021 at 01:35:17PM +0100, Thomas Hellström (Intel) wrote:
On 3/24/21 1:24 PM, Jason Gunthorpe wrote:
On Wed, Mar 24, 2021 at 10:56:43AM +0100, Daniel Vetter wrote:
On Tue, Mar 23, 2021 at 06:06:53PM +0100, Thomas Hellström (Intel) wrote:
On 3/23/21 5:37 PM, Jason Gunthorpe wrote:
On Tue, Mar 23, 2021 at 05:34:51PM +0100, Thomas Hellström (Intel) wrote:
@@ -210,6 +211,20 @@ static vm_fault_t ttm_bo_vm_insert_huge(struct vm_fault *vmf,
if ((pfn & (fault_page_size - 1)) != 0)
goto out_fallback;
+ /*
+ * Huge entries must be special, that is marking them as devmap
+ * with no backing device map range. If there is a backing
+ * range, Don't insert a huge entry.
+ * If this check turns out to be too much of a performance hit,
+ * we can instead have drivers indicate whether they may have
+ * backing device map ranges and if not, skip this lookup.
+ */
I think we can do this statically:
- if it's system memory we know there's no devmap for it, and we do the
trick to block gup_fast
Yes, that should work.
- if it's iomem, we know gup_fast wont work anyway if don't set PFN_DEV,
so might as well not do that
I think gup_fast will unfortunately mistake a huge iomem page for an
ordinary page and try to access a non-existant struct page for it, unless we
do the devmap trick.
And the lookup would then be for the rare case where a driver would have
already registered a dev_pagemap for an iomem area which may also be mapped
through TTM (like the patch from Felix a couple of weeks ago). If a driver
can promise not to do that, then we can safely remove the lookup.
Isn't the devmap PTE flag arch optional? Does this fall back to not
using huge pages on arches that don't support it?
Good point. No, currently it's only conditioned on transhuge page support.
Need to condition it on also devmap support.
Also, I feel like this code to install "pte_special" huge pages does
not belong in the drm subsystem..
I could add helpers in huge_memory.c:
vmf_insert_pfn_pmd_prot_special() and
vmf_insert_pfn_pud_prot_special()
The somewhat annoying thing is that we'd need an error code so we fall
back to pte fault handling. That's at least my understanding of how
pud/pmd fault handling works. Not sure how awkward that is going to be
with the overall fault handling flow.
But aside from that I think this makes tons of sense.
Why should the driver be so specific?
vmf_insert_pfn_range_XXX()
And it will figure out the optimal way to build the page tables.
Driver should provide the largest physically contiguous range it can
I figure that would probably work, but since the huge_fault() interface is
already providing the size of the fault based on how the pagetable is
currently populated I figure that would have to move a lot of that logic
into that helper...
But we don't really care about the size of the fault when we stuff the
pfns.
The device might use it when handling the fault, but once the fault is
handled the device knows what the contiguous pfn range is that it has
available to stuff into the page tables, it just tells the vmf_insert
what it was able to create, and it creates the necessary page table
structure.
The size of the hole in the page table is really only advisory, the
device may not want to make a 2M or 1G page entry and may prefer to
only create 4k.
In an ideal world the creation/destruction of page table levels would
by dynamic at this point, like THP.
Hmm, but I'm not sure what problem we're trying to solve by changing the
interface in this way?
Currently if the core vm requests a huge pud, we give it one, and if we
can't or don't want to (because of dirty-tracking, for example, which is
always done on 4K page-level) we just return VM_FAULT_FALLBACK, and the
fault is retried at a lower level. Also, determining whether we have a
contigous range is not free, so we don't want to do that unnecessarily.
/Thomas
