On Mon, 2020-10-26 at 07:55 -0600, Jens Axboe wrote: > I've tried to reproduce this as well, to no avail. Qian, could you perhaps > detail the setup? What kind of storage, kernel config, compiler, etc. > So far I have only been able to reproduce on this Intel platform: HPE DL560 gen10 Intel(R) Xeon(R) Gold 6154 CPU @ 3.00GHz 131072 MB memory, 1000 GB disk space (smartpqi nvme) It was running some CPU and memory hotplug, KVM and then LTP workloads (syscalls, mm, and fs). Finally, it was always this LTP test case to trigger it: # export LTPROOT; rwtest -N iogen01 -i 120s -s read,write -Da -Dv -n 2 500b:$TMPDIR/doio.f1.$$ 1000b:$TMPDIR/doio.f2.$$ https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/fs/doio/rwtest gcc-8.3.1-5.1.el8.x86_64 .config: https://git.code.tencent.com/cail/linux-mm/blob/master/x86.config == storage information == [ 46.131150] smartpqi 0000:23:00.0: Online Firmware Activation enabled [ 46.138495] smartpqi 0000:23:00.0: Serial Management Protocol enabled [ 46.145701] smartpqi 0000:23:00.0: New Soft Reset Handshake enabled [ 46.152705] smartpqi 0000:23:00.0: RAID IU Timeout enabled [ 46.158934] smartpqi 0000:23:00.0: TMF IU Timeout enabled [ 46.168740] scsi host0: smartpqi [ 47.750425] nvme nvme1: 31/0/0 default/read/poll queues [ 47.826211] scsi 0:0:0:0: Direct-Access ATA MM1000GEFQV HPG8 PQ: 0 ANSI: 6 [ 47.841752] smartpqi 0000:23:00.0: added 0:0:0:0 0000000000000000 Direct-Access ATA MM1000GEFQV AIO+ qd=32 [ 47.941249] nvme1n1: p1 [ 47.943078] scsi 0:0:1:0: Enclosure HPE Smart Adapter 2.62 PQ: 0 ANSI: 5 [ 47.958506] smartpqi 0000:23:00.0: added 0:0:1:0 51402ec001f36448 Enclosure HPE Smart Adapter AIO- [ 47.962844] nvme nvme0: 31/0/0 default/read/poll queues [ 48.015511] scsi 0:2:0:0: RAID HPE P408i-a SR Gen10 2.62 PQ: 0 ANSI: 5 [ 48.029736] smartpqi 0000:23:00.0: added 0:2:0:0 0000000000000000 RAID HPE P408i-a SR Gen10 [ 48.042711] smartpqi 0000:4e:00.0: Microsemi Smart Family Controller found [ 48.149820] nvme0n1: p1 [ 48.956194] smartpqi 0000:4e:00.0: Online Firmware Activation enabled [ 48.963399] smartpqi 0000:4e:00.0: Serial Management Protocol enabled [ 48.970625] smartpqi 0000:4e:00.0: New Soft Reset Handshake enabled [ 48.977645] smartpqi 0000:4e:00.0: RAID IU Timeout enabled [ 48.983873] smartpqi 0000:4e:00.0: TMF IU Timeout enabled [ 48.994687] scsi host1: smartpqi [ 50.612955] scsi 1:0:0:0: Enclosure HPE Smart Adapter 2.62 PQ: 0 ANSI: 5 [ 50.628219] smartpqi 0000:4e:00.0: added 1:0:0:0 51402ec01040ffc8 Enclosure HPE Smart Adapter AIO- [ 50.681859] scsi 1:2:0:0: RAID HPE E208i-p SR Gen10 2.62 PQ: 0 ANSI: 5 [ 50.695843] smartpqi 0000:4e:00.0: added 1:2:0:0 0000000000000000 RAID HPE E208i-p SR Gen10 [ 50.856683] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 50.865195] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 50.871354] sd 0:0:0:0: [sda] Write Protect is off [ 50.876956] sd 0:0:0:0: [sda] Mode Sense: 46 00 10 08 [ 50.877299] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 50.898824] sda: sda1 sda2 sda3 [ 50.943835] sd 0:0:0:0: [sda] Attached SCSI disk
