On 30 Jul 11 17:30, Shaohua Li wrote: > On Sat, Jul 30, 2011 at 06:12:31AM +0800, Larry Bassel wrote: > > We want to handle the following 2 use cases we have on > > some of our (ARM) platforms: > > > > 1. A platform where part of the memory may be powered > > off. The location and size of this memory is not known > > until the kernel parses the memory tags (there aren't > > any non-standard tags used, but the memory layout and > > a memory bank size which is obtained from HW are used > > to figure out where and how large this memory is). All > > of this memory must either be on or off. For a given > > configuration the location of this memory can't be moved. > > > > 2. A (different) platform where part of the memory > > is occasionally needed as a large physically contiguous > > block, but usually is not (and then should be usable > > by the kernel as normal memory). When the memory is > > needed for the contiguous block, the pages in this > > range currently being used by the kernel will > > need to be migrated out. > > > > The size of this is known at compile time and can be > > placed at any reasonable place in memory (but should > > be SPARSEMEM section aligned -- its size may however > > not be a power of 2 and thus this memory could > > span more than one section). This memory will not be > > powered off, but must either be completely used for > > one purpose or the other. > > > > The size of memory in question for #1 is generally > > much larger than that of #2. > > > > Memory hotplug/hotremove (logical and physical for #1, > > only logical for #2) approximately solves these problems, > > but there is some functionality we need that AFAIK is > > not present: > > > > * The memory in #1 and #2 above must be in a movable > > zone so that the chance of migration is maximized. > > I'm familiar with the kernelcore= and movablecore= > > commandline options, but they don't do what is necessary > > here, because we need control on where the movable zone > > is formed as well as the size. Also the location and size > > of these special memory areas is not known until the > > kernel comes up (in #1 it is conceivable that the bootloader > > could locate the memory that can be powered on and off and > > pass it in via some commandline option, but AFAICT this won't > > work at all for #2). > > > > One could hack up find_zone_movable_pfns_for_nodes() presumably, > > but I wonder if there is an already existing way of doing > > this (or at least a clean extension to the current > > functionality that someone might suggest). > > > > Would CONFIG_ARCH_POPULATES_NODE_MAP help here? Does anyone > > use this? It doesn't seem to be in any defconfig or Kconfig > > on 3.0 (or earlier versions I've looked at). > > > > Perhaps CMA (which is not merged yet and AFAIK still has some > > issues on ARM) might handle #2 better than memory > > hotplug/hotremove. Or is there a better way to handle #2 > > than either CMA or memory hotplug? > is such memory always at the end of memory? if yes, such memory > can be added to MOVABLE_ZONE. In use case #1 yes, maybe not in #2 (we can arrange it to be at the end of memory, but then might waste memory as it may not be aligned on a SPARSEMEM section boundary and so would need to be padded). > or if such memory can be at the middle of memory, maybe we can add > a new mirgate type, the migrate type is movable but other type allocation > can't fallback into. > > Thanks, > Shaohua Larry > > -- > To unsubscribe, send a message with 'unsubscribe linux-mm' in > the body to majordomo@xxxxxxxxx. For more info on Linux MM, > see: http://www.linux-mm.org/ . > Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/ > Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a> -- Sent by an employee of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum. -- To unsubscribe, send a message with 'unsubscribe linux-mm' in the body to majordomo@xxxxxxxxx. For more info on Linux MM, see: http://www.linux-mm.org/ . Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/ Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>