On Tue, Jul 26, 2011 at 04:47:41PM +0100, Mel Gorman wrote:
> On Mon, Jul 25, 2011 at 10:19:14PM +0200, Johannes Weiner wrote:
> > Hello!
> >
> > Writing back single file pages during reclaim exhibits bad IO
> > patterns, but we can't just stop doing that before the VM has other
> > means to ensure the pages in a zone are reclaimable.
> >
> > Over time there were several suggestions of at least doing
> > write-around of the pages in inode-proximity when the need arises to
> > clean pages during memory pressure. But even that would interrupt
> > writeback from the flushers, without any guarantees that the nearby
> > inode-pages are even sitting on the same troubled zone.
> >
> > The reason why dirty pages reach the end of LRU lists in the first
> > place is in part because the dirty limits are a global restriction
> > while most systems have more than one LRU list that are different in
> > size. Multiple nodes have multiple zones have multiple file lists but
> > at the same time there is nothing to balance the dirty pages between
> > the lists except for reclaim writing them out upon encounter.
> >
> > With around 4G of RAM, a x86_64 machine of mine has a DMA32 zone of a
> > bit over 3G, a Normal zone of 500M, and a DMA zone of 15M.
> >
> > A linear writer can quickly fill up the Normal zone, then the DMA32
> > zone, throttled by the dirty limit initially. The flushers catch up,
> > the zones are now mostly full of clean pages and memory reclaim kicks
> > in on subsequent allocations. The pages it frees from the Normal zone
> > are quickly filled with dirty pages (unthrottled, as the much bigger
> > DMA32 zone allows for a huge number of dirty pages in comparison to
> > the Normal zone). As there are also anon and active file pages on the
> > Normal zone, it is not unlikely that a significant amount of its
> > inactive file pages are now dirty [ foo=zone(global) ]:
> >
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=112313(821289) active=9942(10039) isolated=27(27) dirty=59709(146944) writeback=739(4017)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=111102(806876) active=9925(10022) isolated=32(32) dirty=72125(146914) writeback=957(3972)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=110493(803374) active=9871(9978) isolated=32(32) dirty=57274(146618) writeback=4088(4088)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=111957(806559) active=9871(9978) isolated=32(32) dirty=65125(147329) writeback=456(3866)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=110601(803978) active=9860(9973) isolated=27(27) dirty=63792(146590) writeback=61(4276)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=111786(804032) active=9860(9973) isolated=0(64) dirty=64310(146998) writeback=1282(3847)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=111643(805651) active=9860(9982) isolated=32(32) dirty=63778(147217) writeback=1127(4156)
> > reclaim: blkdev_writepage+0x0/0x20 zone=Normal inactive=111678(804709) active=9859(10112) isolated=27(27) dirty=81673(148224) writeback=29(4233)
> >
> > [ These prints occur only once per reclaim invocation, so the actual
> > ->writepage calls are more frequent than the timestamp may suggest. ]
> >
> > In the scenario without the Normal zone, first the DMA32 zone fills
> > up, then the DMA zone. When reclaim kicks in, it is presented with a
> > DMA zone whose inactive pages are all dirty -- and dirtied most
> > recently at that, so the flushers really had abysmal chances at making
> > some headway:
> >
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=776(430813) active=2(2931) isolated=32(32) dirty=814(68649) writeback=0(18765)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=726(430344) active=2(2931) isolated=32(32) dirty=764(67790) writeback=0(17146)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=729(430838) active=2(2931) isolated=32(32) dirty=293(65303) writeback=468(20122)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=757(431181) active=2(2931) isolated=32(32) dirty=63(68851) writeback=731(15926)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=758(432808) active=2(2931) isolated=32(32) dirty=645(64106) writeback=0(19666)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=726(431018) active=2(2931) isolated=32(32) dirty=740(65770) writeback=10(17907)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=697(430467) active=2(2931) isolated=32(32) dirty=743(63757) writeback=0(18826)
> > reclaim: xfs_vm_writepage+0x0/0x4f0 zone=DMA inactive=693(430951) active=2(2931) isolated=32(32) dirty=626(54529) writeback=91(16198)
> >
>
> Patches 1-7 of the series "Reduce filesystem writeback from page
> reclaim" should have been able to cope with this as well by marking
> the dirty pages PageReclaim and continuing on. While it could still
> take some time before ZONE_DMA is cleaned, it is very unlikely that
> it is the preferred zone for allocation.
My changes can not fully prevent dirty pages from reaching the LRU
tail, so IMO we want your patches in any case (sorry I haven't replied
yet, but I went through them and they look good to me. Acks coming
up). But this should reduce what reclaim has to skip and shuffle.
> > The idea behind this patch set is to take the ratio the global dirty
> > limits have to the global memory state and put it into proportion to
> > the individual zone. The allocator ensures that pages allocated for
> > being written to in the page cache are distributed across zones such
> > that there are always enough clean pages on a zone to begin with.
> >
>
> Ok, I comment on potential lowmem pressure problems with this in the
> patch itself.
>
> > I am not yet really satisfied as it's not really orthogonal or
> > integrated with the other writeback throttling much, and has rough
> > edges here and there, but test results do look rather promising so
> > far:
> >
>
> I'd consider that the idea behind this patchset is independent of
> patches 1-7 of the "Reduce filesystem writeback from page reclaim"
> series although it may also allow the application of patch 8 from
> that series. Would you agree or do you think the series should be
> mutually exclusive?
My patchset was triggered by patch 8 of your series, as I think we can
not simply remove our only measure to stay on top of the dirty pages
from a per-zone perspective.
But I think your patches 1-7 and this series complement each other in
that one series tries to keep the dirty pages per-zone on sane levels
and the other series improves how we deal with what dirty pages still
end up at the lru tails.
> > --- Copying 8G to fuse-ntfs on USB stick in 4G machine
> >
>
> Unusual choice of filesystem :) It'd also be worth testing ext3, ext4,
> xfs and btrfs to make sure there are no surprises.
Yeah, testing has been really shallow so far as my test box is
occupied with the exclusive memcg lru stuff.
Also, this is the stick my TV has to be able to read from ;-)
> > 3.0:
> >
> > Performance counter stats for 'dd if=/dev/zero of=zeroes bs=32k count=262144' (6 runs):
> >
> > 140,671,831 cache-misses # 4.923 M/sec ( +- 0.198% ) (scaled from 82.80%)
> > 726,265,014 cache-references # 25.417 M/sec ( +- 1.104% ) (scaled from 83.06%)
> > 144,092,383 branch-misses # 4.157 % ( +- 0.493% ) (scaled from 83.17%)
> > 3,466,608,296 branches # 121.319 M/sec ( +- 0.421% ) (scaled from 67.89%)
> > 17,882,351,343 instructions # 0.417 IPC ( +- 0.457% ) (scaled from 84.73%)
> > 42,848,633,897 cycles # 1499.554 M/sec ( +- 0.604% ) (scaled from 83.08%)
> > 236 page-faults # 0.000 M/sec ( +- 0.323% )
> > 8,026 CPU-migrations # 0.000 M/sec ( +- 6.291% )
> > 2,372,358 context-switches # 0.083 M/sec ( +- 0.003% )
> > 28574.255540 task-clock-msecs # 0.031 CPUs ( +- 0.409% )
> >
> > 912.625436885 seconds time elapsed ( +- 3.851% )
> >
> > nr_vmscan_write 667839
> >
> > 3.0-per-zone-dirty:
> >
> > Performance counter stats for 'dd if=/dev/zero of=zeroes bs=32k count=262144' (6 runs):
> >
> > 140,791,501 cache-misses # 3.887 M/sec ( +- 0.186% ) (scaled from 83.09%)
> > 816,474,193 cache-references # 22.540 M/sec ( +- 0.923% ) (scaled from 83.16%)
> > 154,500,577 branch-misses # 4.302 % ( +- 0.495% ) (scaled from 83.15%)
> > 3,591,344,338 branches # 99.143 M/sec ( +- 0.402% ) (scaled from 67.32%)
> > 18,713,190,183 instructions # 0.338 IPC ( +- 0.448% ) (scaled from 83.96%)
> > 55,285,320,107 cycles # 1526.208 M/sec ( +- 0.588% ) (scaled from 83.28%)
> > 237 page-faults # 0.000 M/sec ( +- 0.302% )
> > 28,028 CPU-migrations # 0.001 M/sec ( +- 3.070% )
> > 2,369,897 context-switches # 0.065 M/sec ( +- 0.006% )
> > 36223.970238 task-clock-msecs # 0.060 CPUs ( +- 1.062% )
> >
> > 605.909769823 seconds time elapsed ( +- 0.783% )
> >
> > nr_vmscan_write 0
> >
>
> Very nice!
>
> > That's an increase of throughput by 30% and no writeback interference
> > from reclaim.
> >
>
> Any idea how much dd was varying in performance on each run? I'd
> still expect a gain but I've found dd to vary wildly at times even
> if conv=fdatasync,fsync is specified.
The fluctuation is in the figures after the 'seconds time elapsed'.
It is less than 1% for the six runs.
Or did you mean something else?
> > As not every other allocation has to reclaim from a Normal zone full
> > of dirty pages anymore, the patched kernel is also more responsive in
> > general during the copy.
> >
> > I am also running fs_mark on XFS on a 2G machine, but the final
> > results are not in yet. The preliminary results appear to be in this
> > ballpark:
> >
> > --- fs_mark -d fsmark-one -d fsmark-two -D 100 -N 150 -n 150 -L 25 -t 1 -S 0 -s $((10 << 20))
> >
> > 3.0:
> >
> > real 20m43.901s
> > user 0m8.988s
> > sys 0m58.227s
> > nr_vmscan_write 3347
> >
> > 3.0-per-zone-dirty:
> >
> > real 20m8.012s
> > user 0m8.862s
> > sys 1m2.585s
> > nr_vmscan_write 161
> >
>
> Thats roughly a 2.8% gain. I was seeing about 4.2% but was testing with
> mem=1G, not 2G and there are a lot of factors at play.
[...]
> > #4 adds per-zone dirty throttling for __GFP_WRITE allocators, #5
> > passes __GFP_WRITE from the grab_cache_page* functions in the hope to
> > get most writers and no readers; I haven't checked all sites yet.
> >
> > Discuss! :-)
> >
>
> I think the performance gain may be due to flusher threads simply
> being more aggressive and I suspect it will have a smaller effect on
> NUMA where the flushers could be cleaning pages on the wrong node.
I ran this same test with statistics (which I now realize should
probably become part of this series) and they indicated that the
flushers were not woken a single time from the new code.
All it did in this case was defer future-dirty pages from the Normal
zone to the DMA32 zone.
My understanding is that as the dirty pages are forcibly spread out
into the bigger zone, reclaim and flushers become less likely to step
on each other's toes.
> That said, your figures are very promising and it is worth
> an investigation and you should expand the number of filesystems
> tested. I did a quick set of similar benchmarks locally. I only ran
> dd once which is a major flaw but wanted to get a quick look.
Yeah, more testing is definitely going to happen on this. I tried
other filesystems with one-shot runs as well, just to see if anything
stood out, but nothing conclusive.
> 4 kernels were tested.
>
> vanilla: 3.0
> lesskswapd Patches 1-7 from my series
> perzonedirty Your patches
> lessks-pzdirty Both
>
> Backing storage was a USB key. Kernel was booted with mem=4608M to
> get a 500M highest zone similar to yours.
I think what I wrote was a bit misleading. The zone size example was
taken from my desktop machine to simply point out the different zones
sizes in a simple UMA machine. But I ran this test on my laptop,
where the Normal zone is ~880MB (226240 present pages).
The dirty_background_ratio is 10, dirty_ratio is 20, btw, ISTR that
you had set them higher and I expect that to be a factor.
The dd throughput is ~14 MB/s on the pzd kernel.
> SIMPLE WRITEBACK XFS
> simple-writeback writeback-3.0.0 writeback-3.0.0 3.0.0-lessks
> 3.0.0-vanilla lesskswapd-v3r1 perzonedirty-v1r1 pzdirty-v3r1
> 1 526.83 ( 0.00%) 468.52 (12.45%) 542.05 (-2.81%) 464.42 (13.44%)
> MMTests Statistics: duration
> User/Sys Time Running Test (seconds) 7.27 7.34 7.69 7.96
> Total Elapsed Time (seconds) 528.64 470.36 543.86 466.33
>
> Direct pages scanned 0 0 0 0
> Direct pages reclaimed 0 0 0 0
> Kswapd pages scanned 1058036 1167219 1060288 1169190
> Kswapd pages reclaimed 988591 979571 980278 981009
> Kswapd efficiency 93% 83% 92% 83%
> Kswapd velocity 2001.430 2481.544 1949.561 2507.216
> Direct efficiency 100% 100% 100% 100%
> Direct velocity 0.000 0.000 0.000 0.000
> Percentage direct scans 0% 0% 0% 0%
> Page writes by reclaim 4463 4587 4816 4910
> Page reclaim invalidate 0 145938 0 136510
>
> Very few pages are being written back so I suspect any difference in
> performance would be due to dd simply being very variable. I wasn't
> running the monitoring that would tell me if the "Page writes" were
> file-backed or anonymous but I assume they are file-backed. Your
> patches did not seem to have much affect on the number of pages
> written.
That's odd. While it did not completely get rid of all file writes
from reclaim, it reduced them consistently in all my tests so far.
I don't have swap space on any of my machines, but I wouldn't expect
this to make a difference.
> Note that direct reclaim is not triggered by this workload at all.
Same here, not a single allocstall.
> SIMPLE WRITEBACK EXT4
> simple-writeback writeback-3.0.0 writeback-3.0.0 3.0.0-lessks
> 3.0.0-vanilla lesskswapd-v3r1 perzonedirty-v1r1 pzdirty-v3r1
> 1 369.80 ( 0.00%) 370.80 (-0.27%) 384.08 (-3.72%) 371.85 (-0.55%)
> MMTests Statistics: duration
> User/Sys Time Running Test (seconds) 7.62 7.7 8.05 7.86
> Total Elapsed Time (seconds) 371.74 372.80 386.06 373.86
>
> Direct pages scanned 0 0 0 0
> Direct pages reclaimed 0 0 0 0
> Kswapd pages scanned 1169587 1186543 1167690 1180982
> Kswapd pages reclaimed 988154 987885 987220 987826
> Kswapd efficiency 84% 83% 84% 83%
> Kswapd velocity 3146.250 3182.787 3024.633 3158.888
> Direct efficiency 100% 100% 100% 100%
> Direct velocity 0.000 0.000 0.000 0.000
> Percentage direct scans 0% 0% 0% 0%
> Page writes by reclaim 141229 4714 141804 4608
> Page writes skipped 0 0 0 0
> Page reclaim invalidate 0 144009 0 144012
> Slabs scanned 3712 3712 3712 3712
>
> Not much different here than what is in xfs other than to note that
> your patches do not hurt "Kswapd efficiency" as the scanning rates
> remain more or less constant.
>
> SIMPLE WRITEBACK EXT3
> simple-writeback writeback-3.0.0 writeback-3.0.0 3.0.0-lessks
> 3.0.0-vanilla lesskswapd-v3r1 perzonedirty-v1r1 pzdirty-v3r1
> 1 1291.48 ( 0.00%) 1205.11 ( 7.17%) 1287.53 ( 0.31%) 1190.54 ( 8.48%)
> MMTests Statistics: duration
> User/Sys Time Running Test (seconds) 11.01 11.04 11.44 11.39
> Total Elapsed Time (seconds) 1295.44 1208.90 1293.81 1195.37
>
> Direct pages scanned 0 0 0 0
> Direct pages reclaimed 0 0 0 0
> Kswapd pages scanned 1073001 1183622 1065262 1179216
> Kswapd pages reclaimed 985900 985521 979727 979873
> Kswapd efficiency 91% 83% 91% 83%
> Kswapd velocity 828.291 979.090 823.353 986.486
> Direct efficiency 100% 100% 100% 100%
> Direct velocity 0.000 0.000 0.000 0.000
> Percentage direct scans 0% 0% 0% 0%
> Page writes by reclaim 13444 4664 13557 4928
> Page writes skipped 0 0 0 0
> Page reclaim invalidate 0 146167 0 146495
>
> Other than noting that ext3 is *very* slow in comparison to xfs and
> ext4, there was little of interest in this.
>
> So I'm not seeing the same reduction in number of pages written back
> as you saw and I'm not seeing the same performance gains either. I
> wonder why that is but possibilities include you using fuse-ntfs or
> maybe it's just the speed of the USB disk you are using that is a
> factor?
I will try out other filesystems here as well.
> As dd is variable, I'm rerunning the tests to do 4 iterations and
> multiple memory sizes for just xfs and ext4 to see what falls out. It
> should take about 14 hours to complete assuming nothing screws up.
Awesome, thanks!
---
From: Johannes Weiner <jweiner@xxxxxxxxxx>
Subject: mm: per-zone dirty limit statistics
Signed-off-by: Johannes Weiner <jweiner@xxxxxxxxxx>
---
include/linux/vm_event_item.h | 4 ++++
include/linux/vmstat.h | 3 +++
mm/page-writeback.c | 8 ++++++--
mm/page_alloc.c | 4 +++-
mm/vmstat.c | 4 ++++
5 files changed, 20 insertions(+), 3 deletions(-)
diff --git a/include/linux/vm_event_item.h b/include/linux/vm_event_item.h
index 03b90cdc..6bfc604 100644
--- a/include/linux/vm_event_item.h
+++ b/include/linux/vm_event_item.h
@@ -58,6 +58,10 @@ enum vm_event_item { PGPGIN, PGPGOUT, PSWPIN, PSWPOUT,
THP_COLLAPSE_ALLOC_FAILED,
THP_SPLIT,
#endif
+ FOR_ALL_ZONES(DIRTY_ALLOC_DENIED),
+ FOR_ALL_ZONES(DIRTY_WAKE_FLUSHERS),
+ DIRTY_WAIT_CONGESTION,
+
NR_VM_EVENT_ITEMS
};
diff --git a/include/linux/vmstat.h b/include/linux/vmstat.h
index bcd942f..5926225 100644
--- a/include/linux/vmstat.h
+++ b/include/linux/vmstat.h
@@ -80,6 +80,9 @@ static inline void vm_events_fold_cpu(int cpu)
#endif /* CONFIG_VM_EVENT_COUNTERS */
+#define count_zone_vm_event(item, zone) \
+ count_vm_event(item##_NORMAL - ZONE_NORMAL + zone_idx(zone))
+
#define __count_zone_vm_events(item, zone, delta) \
__count_vm_events(item##_NORMAL - ZONE_NORMAL + \
zone_idx(zone), delta)
diff --git a/mm/page-writeback.c b/mm/page-writeback.c
index ce673ec..0937382 100644
--- a/mm/page-writeback.c
+++ b/mm/page-writeback.c
@@ -748,8 +748,10 @@ void try_to_writeback_pages(struct zonelist *zonelist, gfp_t gfp_mask,
if (nr_reclaimable + nr_writeback <= background_thresh)
continue;
- if (nr_reclaimable > nr_writeback)
+ if (nr_reclaimable > nr_writeback) {
+ count_zone_vm_event(DIRTY_WAKE_FLUSHERS, zone);
wakeup_flusher_threads(nr_reclaimable - nr_writeback);
+ }
if (nr_reclaimable + nr_writeback <= dirty_thresh)
continue;
@@ -757,8 +759,10 @@ void try_to_writeback_pages(struct zonelist *zonelist, gfp_t gfp_mask,
nr_exceeded++;
}
- if (nr_zones == nr_exceeded)
+ if (nr_zones == nr_exceeded) {
+ count_vm_event(DIRTY_WAIT_CONGESTION);
congestion_wait(BLK_RW_ASYNC, HZ/10);
+ }
}
/*
diff --git a/mm/page_alloc.c b/mm/page_alloc.c
index 1fac154..5939a98 100644
--- a/mm/page_alloc.c
+++ b/mm/page_alloc.c
@@ -1666,8 +1666,10 @@ zonelist_scan:
!cpuset_zone_allowed_softwall(zone, gfp_mask))
goto try_next_zone;
- if ((gfp_mask & __GFP_WRITE) && !zone_dirty_ok(zone))
+ if ((gfp_mask & __GFP_WRITE) && !zone_dirty_ok(zone)) {
+ count_zone_vm_event(DIRTY_ALLOC_DENIED, zone);
goto this_zone_full;
+ }
BUILD_BUG_ON(ALLOC_NO_WATERMARKS < NR_WMARK);
if (!(alloc_flags & ALLOC_NO_WATERMARKS)) {
diff --git a/mm/vmstat.c b/mm/vmstat.c
index 20c18b7..d302a77 100644
--- a/mm/vmstat.c
+++ b/mm/vmstat.c
@@ -786,6 +786,10 @@ const char * const vmstat_text[] = {
"thp_split",
#endif
+ TEXTS_FOR_ZONES("dirty_alloc_denied")
+ TEXTS_FOR_ZONES("dirty_wake_flushers")
+ "dirty_wait_congestion",
+
#endif /* CONFIG_VM_EVENTS_COUNTERS */
};
#endif /* CONFIG_PROC_FS || CONFIG_SYSFS */
--
1.7.6
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxx. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>