From: Andrey Konovalov <andreyknvl@xxxxxxxxxx> Subject: kcov: check kcov_softirq in kcov_remote_stop() kcov_remote_stop() should check that the corresponding kcov_remote_start() actually found the specified remote handle and started collecting coverage. This is done by checking the per thread kcov_softirq flag. A particular failure scenario where this was observed involved a softirq with a remote coverage collection section coming between check_kcov_mode() and the access to t->kcov_area in __sanitizer_cov_trace_pc(). In that softirq kcov_remote_start() bailed out after kcov_remote_find() check, but the matching kcov_remote_stop() didn't check if kcov_remote_start() succeeded, and overwrote per thread kcov parameters with invalid (zero) values. Link: http://lkml.kernel.org/r/fcd1cd16eac1d2c01a66befd8ea4afc6f8d09833.1591576806.git.andreyknvl@xxxxxxxxxx Fixes: 5ff3b30ab57d ("kcov: collect coverage from interrupts") Signed-off-by: Andrey Konovalov <andreyknvl@xxxxxxxxxx> Reviewed-by: Dmitry Vyukov <dvyukov@xxxxxxxxxx> Cc: Alexander Potapenko <glider@xxxxxxxxxx> Cc: Marco Elver <elver@xxxxxxxxxx> Cc: Tetsuo Handa <penguin-kernel@xxxxxxxxxxxxxxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- kernel/kcov.c | 26 ++++++++++++++++++-------- 1 file changed, 18 insertions(+), 8 deletions(-) --- a/kernel/kcov.c~kcov-check-kcov_softirq-in-kcov_remote_stop +++ a/kernel/kcov.c @@ -427,7 +427,8 @@ void kcov_task_exit(struct task_struct * * WARN_ON(!kcov->remote && kcov->t != t); * * For KCOV_REMOTE_ENABLE devices, the exiting task is either: - * 2. A remote task between kcov_remote_start() and kcov_remote_stop(). + * + * 1. A remote task between kcov_remote_start() and kcov_remote_stop(). * In this case we should print a warning right away, since a task * shouldn't be exiting when it's in a kcov coverage collection * section. Here t points to the task that is collecting remote @@ -437,7 +438,7 @@ void kcov_task_exit(struct task_struct * * WARN_ON(kcov->remote && kcov->t != t); * * 2. The task that created kcov exiting without calling KCOV_DISABLE, - * and then again we can make sure that t->kcov->t == t: + * and then again we make sure that t->kcov->t == t: * WARN_ON(kcov->remote && kcov->t != t); * * By combining all three checks into one we get: @@ -764,7 +765,7 @@ static const struct file_operations kcov * Internally, kcov_remote_start() looks up the kcov device associated with the * provided handle, allocates an area for coverage collection, and saves the * pointers to kcov and area into the current task_struct to allow coverage to - * be collected via __sanitizer_cov_trace_pc() + * be collected via __sanitizer_cov_trace_pc(). * In turns kcov_remote_stop() clears those pointers from task_struct to stop * collecting coverage and copies all collected coverage into the kcov area. */ @@ -972,16 +973,25 @@ void kcov_remote_stop(void) local_irq_restore(flags); return; } - kcov = t->kcov; - area = t->kcov_area; - size = t->kcov_size; - sequence = t->kcov_sequence; - + /* + * When in softirq, check if the corresponding kcov_remote_start() + * actually found the remote handle and started collecting coverage. + */ + if (in_serving_softirq() && !t->kcov_softirq) { + local_irq_restore(flags); + return; + } + /* Make sure that kcov_softirq is only set when in softirq. */ if (WARN_ON(!in_serving_softirq() && t->kcov_softirq)) { local_irq_restore(flags); return; } + kcov = t->kcov; + area = t->kcov_area; + size = t->kcov_size; + sequence = t->kcov_sequence; + kcov_stop(t); if (in_serving_softirq()) { t->kcov_softirq = 0; _
