On Fri, Feb 28, 2020 at 12:16 PM Nicolas Saenz Julienne <nsaenzjulienne@xxxxxxx> wrote: > > On Fri, 2020-02-28 at 11:56 -0800, Jonathan Richardson wrote: > > This is stingray (arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts). > > cma is specified on cmdline as "cma=1G". The full boot log was in the > > attachment. > > Would you mind attaching it again, I was added to the conversation later. Sure, it is attached. Thanks for taking a look. This is a boot with "arch/arm64/configs/defconfig" and the previously mentioned dtb. Jon
--- STARTING KERNEL bootcmd=FS2:\Image.2 root=/dev/mmcblk0p4 rw rootwait earlycon=uart8250,mmio32,0x68A10000 earlyelog =0x8f110000,0x10000 console=ttyS0,115200n8 hugepages=0 cma=1G crashkernel=512M pci=pcie_bus_safe pci ehp.pciehp_poll_mode=1 pciehp.pciehp_poll_time=5 vfio_pci.disable_idle_d3=1 pcie_ports=native maxcpu s=8 bgmac_platform.ethaddr=00:10:18:9B:05:D3 ip=10.136.13.29:10.136.4.151:10.136.13.1:255.255.255.0 :::off EFI stub: Booting Linux Kernel... EFI stub: EFI_RNG_PROTOCOL unavailable, no randomness supplied EFI stub: Using DTB from configuration table EFI stub: Exiting boot services and installing virtual address map... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.5.0 (oe-user@oe-host) (gcc version 8.3.0 (GCC)) #1 SMP PREEMPT Thu Feb 27 03:17:15 UTC 2020 [ 0.000000] Machine model: Stingray Combo SVK (BCM958742K) [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000068a10000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] printk: bootconsole [earlycon_elog0] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: EFI v2.70 by EDK II [ 0.000000] efi: SMBIOS=0x85c90000 SMBIOS 3.0=0x85a20000 ACPI 2.0=0x85d50000 MEMATTR=0x8945e118 MEMRESERVE=0x85f85018 [ 0.000000] crashkernel reserved: 0x00000000e0000000 - 0x0000000100000000 (512 MB) [ 0.000000] cma: Reserved 1024 MiB at 0x00000000a0000000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000093ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x93fbfce100-0x93fbfcffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] DMA32 [mem 0x00000000c0000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x00000093ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000008563ffff] [ 0.000000] node 0: [mem 0x0000000085640000-0x00000000856affff] [ 0.000000] node 0: [mem 0x00000000856b0000-0x00000000857affff] [ 0.000000] node 0: [mem 0x00000000857b0000-0x000000008588ffff] [ 0.000000] node 0: [mem 0x0000000085890000-0x00000000858fffff] [ 0.000000] node 0: [mem 0x0000000085900000-0x000000008597ffff] [ 0.000000] node 0: [mem 0x0000000085980000-0x0000000085a0ffff] [ 0.000000] node 0: [mem 0x0000000085a10000-0x0000000085d3ffff] [ 0.000000] node 0: [mem 0x0000000085d40000-0x0000000085d5ffff] [ 0.000000] node 0: [mem 0x0000000085d60000-0x0000000085f7ffff] [ 0.000000] node 0: [mem 0x0000000085f80000-0x000000008af4ffff] [ 0.000000] node 0: [mem 0x000000008af50000-0x000000008af8ffff] [ 0.000000] node 0: [mem 0x000000008af90000-0x000000008af9ffff] [ 0.000000] node 0: [mem 0x000000008afa0000-0x000000008afeffff] [ 0.000000] node 0: [mem 0x000000008aff0000-0x000000008cffffff] [ 0.000000] node 0: [mem 0x000000008f220000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000000880200000-0x0000000bffffffff] [ 0.000000] node 0: [mem 0x0000009000000000-0x00000093ffffffff] [ 0.000000] Zeroed struct page in unavailable ranges: 832 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000093ffffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 22 pages/cpu s53016 r8192 d28904 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] CPU features: detected: ARM erratum 1319367 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8248296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: FS2:\Image.2 root=/dev/mmcblk0p4 rw rootwait earlycon=uart8250,mmio32,0x68A10000 earlyelog=0x8f110000,0x10000 console=ttyS0,115200n8 hugepages=0 cma=1G crashkernel=512M pci=pcie_bus_safe pciehp.pciehp_poll_mode=1 pciehp.pciehp_poll_time=5 vfio_pci.disable_idle_d3=1 pcie_ports=native maxcpus=8 bgmac_platform.ethaddr=00:10:18:9B:05:D3 ip=10.136.13.29:10.136.4.151:10.136.13.1:255.255.255.0:::off [ 0.000000] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear) [ 0.000000] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x9c000000-0xa0000000] (64MB) [ 0.000000] Memory: 31203448K/33517440K available (12220K kernel code, 1924K rwdata, 6800K rodata, 5184K init, 476K bss, 1265416K reserved, 1048576K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 960 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000063e00000 [ 0.000000] ITS [mem 0x63c20000-0x63c2ffff] [ 0.000000] ITS@0x0000000063c20000: allocated 32768 Devices @93fb880000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x00000093fb850000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000093fb860000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x448 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 125.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x39a85c4118, max_idle_ns: 881590405314 ns [ 0.000001] sched_clock: 56 bits at 125MHz, resolution 8ns, wraps every 4398046511100ns [ 0.009176] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 152900835740 ns [ 0.020113] Console: colour dummy device 80x25 [ 0.025151] printk: bootconsole [earlycon_elog0] disabled [ 0.031276] printk: console [console_elog0] enabled [ 0.036821] Calibrating delay loop (skipped), value calculated using timer frequency.. 250.00 BogoMIPS (lpj=500000) [ 0.048657] pid_max: default: 32768 minimum: 301 [ 0.053908] LSM: Security Framework initializing [ 0.059237] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.067908] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.101009] ASID allocator initialised with 32768 entries [ 0.115133] rcu: Hierarchical SRCU implementation. [ 0.128586] Platform MSI: gic-its@63c20000 domain created [ 0.134734] PCI/MSI: /scr/interrupt-controller@2c00000/gic-its@63c20000 domain created [ 0.144012] Remapping and enabling EFI services. [ 0.157247] smp: Bringing up secondary CPUs ... I: Cluster #1 entering to snoop/dvm domain I: Cluster #2 entering to snoop/dvm domain I: Cluster #3 entering to snoop/dvm domain [ 0.194484] Detected PIPT I-cache on CPU1 [ 0.194498] GICv3: CPU1: found redistributor 1 region 0:0x0000000063e20000 [ 0.194509] GICv3: CPU1: using allocated LPI pending table @0x00000093fb870000 [ 0.194520] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.226749] Detected PIPT I-cache on CPU2 [ 0.226761] GICv3: CPU2: found redistributor 100 region 0:0x0000000063e40000 [ 0.226781] GICv3: CPU2: using allocated LPI pending table @0x00000093fb8c0000 [ 0.226795] CPU2: Booted secondary processor 0x0000000100 [0x410fd083] [ 0.258508] Detected PIPT I-cache on CPU3 [ 0.258514] GICv3: CPU3: found redistributor 101 region 0:0x0000000063e60000 [ 0.258526] GICv3: CPU3: using allocated LPI pending table @0x00000093fb8d0000 [ 0.258535] CPU3: Booted secondary processor 0x0000000101 [0x410fd083] [ 0.290782] Detected PIPT I-cache on CPU4 [ 0.290791] GICv3: CPU4: found redistributor 200 region 0:0x0000000063e80000 [ 0.290808] GICv3: CPU4: using allocated LPI pending table @0x00000093fb8e0000 [ 0.290820] CPU4: Booted secondary processor 0x0000000200 [0x410fd083] [ 0.322549] Detected PIPT I-cache on CPU5 [ 0.322555] GICv3: CPU5: found redistributor 201 region 0:0x0000000063ea0000 [ 0.322567] GICv3: CPU5: using allocated LPI pending table @0x00000093fb8f0000 [ 0.322576] CPU5: Booted secondary processor 0x0000000201 [0x410fd083] [ 0.354823] Detected PIPT I-cache on CPU6 [ 0.354833] GICv3: CPU6: found redistributor 300 region 0:0x0000000063ec0000 [ 0.354851] GICv3: CPU6: using allocated LPI pending table @0x00000093fb900000 [ 0.354863] CPU6: Booted secondary processor 0x0000000300 [0x410fd083] [ 0.386587] Detected PIPT I-cache on CPU7 [ 0.386594] GICv3: CPU7: found redistributor 301 region 0:0x0000000063ee0000 [ 0.386605] GICv3: CPU7: using allocated LPI pending table @0x00000093fb910000 [ 0.386614] CPU7: Booted secondary processor 0x0000000301 [0x410fd083] [ 0.386644] smp: Brought up 1 node, 8 CPUs [ 0.587825] SMP: Total of 8 processors activated. [ 0.593153] CPU features: detected: 32-bit EL0 Support [ 0.598978] CPU features: detected: CRC32 instructions [ 0.616116] CPU: All CPU(s) started at EL2 [ 0.620768] alternatives: patching kernel code [ 0.626261] devtmpfs: initialized [ 0.631187] KASLR disabled due to lack of seed [ 0.636326] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.647378] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.658823] cma: CMA area reserved could not be activated [ 0.665028] pinctrl core: initialized pinctrl subsystem [ 0.671282] thermal_sys: Registered thermal governor 'step_wise' [ 0.671283] thermal_sys: Registered thermal governor 'power_allocator' [ 0.678291] SMBIOS 3.3.0 present. [ 0.689439] DMI: BRCM BRCM-SR/BRCM-SR, BIOS 0.1 Feb 25 2020 [ 0.695885] NET: Registered protocol family 16 [ 0.701114] DMA: failed to allocate 256 KiB pool for atomic coherent allocation [ 0.709404] audit: initializing netlink subsys (disabled) [ 0.715582] audit: type=2000 audit(0.524:1): state=initialized audit_enabled=0 res=1 [ 0.724371] cpuidle: using governor menu [ 0.728940] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.736945] Serial: AMBA PL011 UART driver [ 0.745611] gpiochip_add_data_with_key: GPIOs 355..505 (689d0000.gpio) failed to register, -517 [ 0.755476] iproc-gpio 689d0000.gpio: unable to add GPIO chip [ 0.764996] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.772595] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.780190] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.787785] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.796327] cryptd: max_cpu_qlen set to 1000 [ 0.802551] ACPI: Interpreter disabled. [ 0.807286] iommu: Default domain type: Translated [ 0.812876] vgaarb: loaded [ 0.816005] SCSI subsystem initialized [ 0.820369] usbcore: registered new interface driver usbfs [ 0.826595] usbcore: registered new interface driver hub [ 0.832634] usbcore: registered new device driver usb [ 0.838550] pps_core: LinuxPPS API ver. 1 registered [ 0.844174] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx> [ 0.854532] PTP clock support registered [ 0.859011] EDAC MC: Ver: 3.0.0 [ 0.862702] Registered efivars operations [ 0.867412] FPGA manager framework [ 0.871279] Advanced Linux Sound Architecture Driver Initialized. [ 0.878425] clocksource: Switched to clocksource arch_sys_counter [ 0.885389] VFS: Disk quotas dquot_6.6.0 [ 0.889847] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.897689] pnp: PnP ACPI: disabled [ 0.903234] NET: Registered protocol family 2 [ 0.908271] tcp_listen_portaddr_hash hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.918242] TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.927947] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.936613] TCP: Hash tables configured (established 262144 bind 65536) [ 0.944161] UDP hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.952154] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.960684] NET: Registered protocol family 1 [ 0.965755] RPC: Registered named UNIX socket transport module. [ 0.972468] RPC: Registered udp transport module. [ 0.977796] RPC: Registered tcp transport module. [ 0.983124] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.990425] PCI: CLS 0 bytes, default 64 [ 0.995231] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.004105] kvm [1]: IPA Size Limit: 44bits [ 1.009118] kvm [1]: GICv3: no GICV resource entry [ 1.014547] kvm [1]: disabling GICv2 emulation [ 1.019590] kvm [1]: GIC system register CPU interface enabled [ 1.026259] kvm [1]: vgic interrupt IRQ1 [ 1.030776] kvm [1]: Hyp mode initialized successfully [ 1.039093] Initialise system trusted keyrings [ 1.044169] workingset: timestamp_bits=44 max_order=23 bucket_order=0 [ 1.053197] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.060004] NFS: Registering the id_resolver key type [ 1.065735] Key type id_resolver registered [ 1.070491] Key type id_legacy registered [ 1.075034] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.082667] 9p: Installing v9fs 9p2000 file system support [ 1.093678] Key type asymmetric registered [ 1.098319] Asymmetric key parser 'x509' registered [ 1.103851] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.112236] io scheduler mq-deadline registered [ 1.117367] io scheduler kyber registered [ 1.123109] brcm-sata-phy 67d02100.sata_phy: registered 1 port(s) [ 1.130053] brcm-sata-phy 67d12100.sata_phy: registered 1 port(s) [ 1.136996] brcm-sata-phy 67d22100.sata_phy: registered 1 port(s) [ 1.143938] brcm-sata-phy 67d32100.sata_phy: registered 1 port(s) [ 1.150879] brcm-sata-phy 67e02100.sata_phy: registered 1 port(s) [ 1.157819] brcm-sata-phy 67e12100.sata_phy: registered 1 port(s) [ 1.164760] brcm-sata-phy 67e22100.sata_phy: registered 1 port(s) [ 1.171702] brcm-sata-phy 67e32100.sata_phy: registered 1 port(s) [ 1.178833] sr-pcie-phy 40000000.phy: Stingray PCIe PHY driver initialized [ 1.187241] pinctrl-single 68a40000.pinconf: please update dts to use #pinctrl-cells = <1> [ 1.196680] pinctrl-single 68a40000.pinconf: 148 pins, size 592 [ 1.203423] pinctrl-single 68a4029c.pinmux: please update dts to use #pinctrl-cells = <1> [ 1.212763] pinctrl-single 68a4029c.pinmux: 155 pins, size 620 [ 1.220566] iproc-pcie 60400000.pcie: host bridge /pcie@60400000 ranges: [ 1.228168] iproc-pcie 60400000.pcie: MEM 0x0010000000..0x002fffffff -> 0x0010000000 [ 1.237453] iproc-pcie 60400000.pcie: not using iProc MSI [ 1.243599] iproc-pcie 60400000.pcie: PCI host bridge to bus 0008:00 [ 1.250801] pci_bus 0008:00: root bus resource [bus 00-01] [ 1.257016] pci_bus 0008:00: root bus resource [mem 0x10000000-0x2fffffff] [ 1.264819] pci 0008:00:00.0: [14e4:d750] type 01 class 0x020000 [ 1.271687] pci 0008:00:00.0: PME# supported from D0 D3hot D3cold [ 1.278608] OF: /pcie@60400000: no msi-map translation for rid 0x0 on (null) [ 1.287041] pci 0008:01:00.0: [14e4:16f0] type 00 class 0x020000 [ 1.293867] pci 0008:01:00.0: reg 0x10: [mem 0x2ff00000-0x2ff0ffff 64bit] [ 1.301568] pci 0008:01:00.0: reg 0x18: [mem 0x2fd00000-0x2fdfffff 64bit pref] [ 1.309760] pci 0008:01:00.0: reg 0x20: [mem 0x2fe00000-0x2fe00fff 64bit pref] [ 1.318001] pci 0008:01:00.0: PME# supported from D0 D3hot D3cold [ 1.324971] pci 0008:01:00.1: [14e4:16f0] type 00 class 0x020000 [ 1.331787] pci 0008:01:00.1: reg 0x10: [mem 0x00000000-0x0000ffff 64bit] [ 1.339487] pci 0008:01:00.1: reg 0x18: [mem 0x00000000-0x000fffff 64bit pref] [ 1.347682] pci 0008:01:00.1: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.355922] pci 0008:01:00.1: PME# supported from D0 D3hot D3cold [ 1.363282] pci 0008:00:00.0: BAR 14: assigned [mem 0x10000000-0x100fffff] [ 1.371076] pci 0008:00:00.0: BAR 15: assigned [mem 0x10100000-0x103fffff 64bit pref] [ 1.379954] pci 0008:01:00.0: BAR 2: assigned [mem 0x10100000-0x101fffff 64bit pref] [ 1.388737] pci 0008:01:00.1: BAR 2: assigned [mem 0x10200000-0x102fffff 64bit pref] [ 1.397521] pci 0008:01:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit] [ 1.405811] pci 0008:01:00.1: BAR 0: assigned [mem 0x10010000-0x1001ffff 64bit] [ 1.414102] pci 0008:01:00.0: BAR 4: assigned [mem 0x10300000-0x10300fff 64bit pref] [ 1.422885] pci 0008:01:00.1: BAR 4: assigned [mem 0x10301000-0x10301fff 64bit pref] [ 1.431670] pci 0008:00:00.0: PCI bridge to [bus 01] [ 1.437296] pci 0008:00:00.0: bridge window [mem 0x10000000-0x100fffff] [ 1.444990] pci 0008:00:00.0: bridge window [mem 0x10100000-0x103fffff 64bit pref] [ 1.453776] pci 0008:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 1.463348] pci 0008:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 1.472919] pci 0008:01:00.1: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 1.483021] EINJ: ACPI disabled. [ 1.490401] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.497935] printk: console [ttyS0] disabled [ 1.502788] 68a10000.uart: ttyS0 at MMIO 0x68a10000 (irq = 86, base_baud = 1562500) is a 16550A [ 1.512669] printk: console [ttyS0] enabled [ 1.512669] printk: console [ttyS0] enabled [ 1.521720] printk: bootconsole [uart8250] disabled [ 1.521720] printk: bootconsole [uart8250] disabled [ 1.532394] 68a20000.uart: ttyS2 at MMIO 0x68a20000 (irq = 87, base_baud = 1562500) is a 16550A [ 1.541500] 68a30000.uart: ttyS3 at MMIO 0x68a30000 (irq = 88, base_baud = 1562500) is a 16550A [ 1.550759] SuperH (H)SCI(F) driver initialized [ 1.555598] msm_serial: driver initialized [ 1.560259] arm-smmu 64000000.mmu: probing hardware configuration... [ 1.566819] arm-smmu 64000000.mmu: SMMUv2 with: [ 1.571495] arm-smmu 64000000.mmu: stage 1 translation [ 1.576888] arm-smmu 64000000.mmu: stage 2 translation [ 1.582280] arm-smmu 64000000.mmu: nested translation [ 1.587582] arm-smmu 64000000.mmu: stream matching with 63 register groups [ 1.594768] arm-smmu 64000000.mmu: 63 context banks (0 stage-2 only) [ 1.601417] arm-smmu 64000000.mmu: Supported page sizes: 0x61311000 [ 1.607974] arm-smmu 64000000.mmu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.614542] arm-smmu 64000000.mmu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.623978] loop: module loaded [ 1.627685] ahci 67d00000.ahci: 67d00000.ahci supply ahci not found, using dummy regulator [ 1.636233] ahci 67d00000.ahci: 67d00000.ahci supply phy not found, using dummy regulator [ 1.644928] platform 67d00000.ahci:sata-port@0: 67d00000.ahci:sata-port@0 supply target not found, using dummy regulator [ 1.656201] ahci 67d00000.ahci: masking port_map 0x1 -> 0x1 [ 1.661962] ahci 67d00000.ahci: SSS flag set, parallel bus scan disabled [ 1.678947] ahci 67d00000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.687749] ahci 67d00000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 1.695672] scsi host0: ahci [ 1.698726] ata1: SATA max UDMA/133 mmio [mem 0x67d00000-0x67d00fff] port 0x100 irq 74 [ 1.706929] ahci 67d10000.ahci: 67d10000.ahci supply ahci not found, using dummy regulator [ 1.715474] ahci 67d10000.ahci: 67d10000.ahci supply phy not found, using dummy regulator [ 1.724070] platform 67d10000.ahci:sata-port@0: 67d10000.ahci:sata-port@0 supply target not found, using dummy regulator [ 1.735334] ahci 67d10000.ahci: masking port_map 0x1 -> 0x1 [ 1.741093] ahci 67d10000.ahci: SSS flag set, parallel bus scan disabled [ 1.758075] ahci 67d10000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.766875] ahci 67d10000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 1.774766] scsi host1: ahci [ 1.777784] ata2: SATA max UDMA/133 mmio [mem 0x67d10000-0x67d10fff] port 0x100 irq 75 [ 1.785989] ahci 67d20000.ahci: 67d20000.ahci supply ahci not found, using dummy regulator [ 1.794547] ahci 67d20000.ahci: 67d20000.ahci supply phy not found, using dummy regulator [ 1.803144] platform 67d20000.ahci:sata-port@0: 67d20000.ahci:sata-port@0 supply target not found, using dummy regulator [ 1.814410] ahci 67d20000.ahci: masking port_map 0x1 -> 0x1 [ 1.820169] ahci 67d20000.ahci: SSS flag set, parallel bus scan disabled [ 1.837149] ahci 67d20000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.845950] ahci 67d20000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 1.853842] scsi host2: ahci [ 1.856860] ata3: SATA max UDMA/133 mmio [mem 0x67d20000-0x67d20fff] port 0x100 irq 76 [ 1.865057] ahci 67d30000.ahci: 67d30000.ahci supply ahci not found, using dummy regulator [ 1.873601] ahci 67d30000.ahci: 67d30000.ahci supply phy not found, using dummy regulator [ 1.882197] platform 67d30000.ahci:sata-port@0: 67d30000.ahci:sata-port@0 supply target not found, using dummy regulator [ 1.893470] ahci 67d30000.ahci: masking port_map 0x1 -> 0x1 [ 1.899228] ahci 67d30000.ahci: SSS flag set, parallel bus scan disabled [ 1.916207] ahci 67d30000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.925009] ahci 67d30000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 1.932892] scsi host3: ahci [ 1.935915] ata4: SATA max UDMA/133 mmio [mem 0x67d30000-0x67d30fff] port 0x100 irq 77 [ 1.944113] ahci 67e00000.ahci: 67e00000.ahci supply ahci not found, using dummy regulator [ 1.952654] ahci 67e00000.ahci: 67e00000.ahci supply phy not found, using dummy regulator [ 1.961261] platform 67e00000.ahci:sata-port@0: 67e00000.ahci:sata-port@0 supply target not found, using dummy regulator [ 1.972526] ahci 67e00000.ahci: masking port_map 0x1 -> 0x1 [ 1.978285] ahci 67e00000.ahci: SSS flag set, parallel bus scan disabled [ 1.995263] ahci 67e00000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.004065] ahci 67e00000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 2.011944] scsi host4: ahci [ 2.014965] ata5: SATA max UDMA/133 mmio [mem 0x67e00000-0x67e00fff] port 0x100 irq 78 [ 2.021781] ata1: SATA link down (SStatus 0 SControl 300) [ 2.023162] ahci 67e10000.ahci: 67e10000.ahci supply ahci not found, using dummy regulator [ 2.037252] ahci 67e10000.ahci: 67e10000.ahci supply phy not found, using dummy regulator [ 2.045844] platform 67e10000.ahci:sata-port@0: 67e10000.ahci:sata-port@0 supply target not found, using dummy regulator [ 2.057112] ahci 67e10000.ahci: masking port_map 0x1 -> 0x1 [ 2.062879] ahci 67e10000.ahci: SSS flag set, parallel bus scan disabled [ 2.079856] ahci 67e10000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.088658] ahci 67e10000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 2.096545] scsi host5: ahci [ 2.099529] ata2: SATA link down (SStatus 0 SControl 300) [ 2.105151] ata6: SATA max UDMA/133 mmio [mem 0x67e10000-0x67e10fff] port 0x100 irq 79 [ 2.113350] ahci 67e20000.ahci: 67e20000.ahci supply ahci not found, using dummy regulator [ 2.121895] ahci 67e20000.ahci: 67e20000.ahci supply phy not found, using dummy regulator [ 2.130490] platform 67e20000.ahci:sata-port@0: 67e20000.ahci:sata-port@0 supply target not found, using dummy regulator [ 2.141757] ahci 67e20000.ahci: masking port_map 0x1 -> 0x1 [ 2.147516] ahci 67e20000.ahci: SSS flag set, parallel bus scan disabled [ 2.164497] ahci 67e20000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.173297] ahci 67e20000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 2.180378] ata3: SATA link down (SStatus 0 SControl 300) [ 2.181189] scsi host6: ahci [ 2.189637] ata7: SATA max UDMA/133 mmio [mem 0x67e20000-0x67e20fff] port 0x100 irq 80 [ 2.197860] ahci 67e30000.ahci: 67e30000.ahci supply ahci not found, using dummy regulator [ 2.206433] ahci 67e30000.ahci: 67e30000.ahci supply phy not found, using dummy regulator [ 2.215127] platform 67e30000.ahci:sata-port@0: 67e30000.ahci:sata-port@0 supply target not found, using dummy regulator [ 2.226408] ahci 67e30000.ahci: masking port_map 0x1 -> 0x1 [ 2.232168] ahci 67e30000.ahci: SSS flag set, parallel bus scan disabled [ 2.249150] ahci 67e30000.ahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.257950] ahci 67e30000.ahci: flags: 64bit ncq sntf stag clo pmp fbs slum part [ 2.262403] ata4: SATA link down (SStatus 0 SControl 300) [ 2.265863] scsi host7: ahci [ 2.274278] ata8: SATA max UDMA/133 mmio [mem 0x67e30000-0x67e30fff] port 0x100 irq 81 [ 2.283438] libphy: iProc MDIO mux bus: probed [ 2.288044] libphy: mdio_mux: probed [ 2.291754] libphy: mdio_mux: probed [ 2.295461] libphy: mdio_mux: probed [ 2.299170] libphy: mdio_mux: probed [ 2.306978] mdio-mux-iproc 68920000.mdio-mux: iProc mdiomux registered [ 2.313907] libphy: Fixed MDIO Bus: probed [ 2.318199] tun: Universal TUN/TAP device driver, 1.6 [ 2.329921] thunder_xcv, ver 1.0 [ 2.333279] thunder_bgx, ver 1.0 [ 2.336620] nicpf, ver 1.0 [ 2.339610] hclge is initializing [ 2.343032] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.346533] ata5: SATA link down (SStatus 0 SControl 300) [ 2.350485] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.350507] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.367557] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.373677] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k [ 2.380861] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.386623] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 2.394705] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 2.400921] sky2: driver version 1.30 [ 2.404922] VFIO - User Level meta-driver version: 0.3 [ 2.410705] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.417442] ehci-pci: EHCI PCI platform driver [ 2.422027] ehci-platform: EHCI generic platform driver [ 2.427460] ehci-orion: EHCI orion driver [ 2.428553] ata6: SATA link down (SStatus 0 SControl 300) [ 2.431630] ehci-exynos: EHCI EXYNOS driver [ 2.441516] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.447900] ohci-pci: OHCI PCI platform driver [ 2.452492] ohci-platform: OHCI generic platform driver [ 2.457922] ohci-exynos: OHCI EXYNOS driver [ 2.462397] usbcore: registered new interface driver usb-storage [ 2.469501] rtc-efi rtc-efi: registered as rtc0 [ 2.474380] i2c /dev entries driver [ 2.478130] bcm-iproc-i2c 689b0000.i2c: bus set to 100000 Hz [ 2.484077] pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator [ 2.494477] bcm-iproc-i2c 689e0000.i2c: bus set to 100000 Hz [ 2.501847] sp805-wdt 689c0000.watchdog: registration successful [ 2.508451] sdhci: Secure Digital Host Controller Interface driver [ 2.514832] sdhci: Copyright(c) Pierre Ossman [ 2.519462] Synopsys Designware Multimedia Card Interface Driver [ 2.520556] ata7: SATA link down (SStatus 0 SControl 300) [ 2.525965] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.537381] sdhci-iproc 68cf1000.sdhci: Adding to iommu group 0 [ 2.543616] sdhci-iproc 68cf2000.sdhci: Adding to iommu group 1 [ 2.550099] ledtrig-cpu: registered to indicate activity on CPUs [ 2.556749] usbcore: registered new interface driver usbhid [ 2.562502] usbhid: USB HID core driver [ 2.567691] NET: Registered protocol family 17 [ 2.572331] 9pnet: Installing 9P2000 support [ 2.576760] Key type dns_resolver registered [ 2.581311] registered taskstats version 1 [ 2.585542] Loading compiled-in X.509 certificates [ 2.593551] ssp-pl022 68a80000.spi: ARM PL022 driver, device ID: 0x00241022 [ 2.596553] ata8: SATA link down (SStatus 0 SControl 300) [ 2.600760] ssp-pl022 68a80000.spi: mapped registers from 0x0000000068a80000 to (____ptrval____) [ 2.615395] ssp-pl022 68a80000.spi: Failed to work in dma mode, work without dma! [ 2.623259] spi-nor spi0.0: w25q32 (4096 Kbytes) [ 2.628504] ssp-pl022 68a90000.spi: ARM PL022 driver, device ID: 0x00241022 [ 2.635707] ssp-pl022 68a90000.spi: mapped registers from 0x0000000068a90000 to (____ptrval____) [ 2.644788] ssp-pl022 68a90000.spi: Failed to work in dma mode, work without dma! [ 2.652632] spi-nor spi1.0: w25q32 (4096 Kbytes) [ 2.657813] dma-pl330 68c10000.dma: Adding to iommu group 2 [ 2.664044] dma-pl330 68c10000.dma: Loaded driver for PL330 DMAC-241330 [ 2.670873] dma-pl330 68c10000.dma: DBUFF-1024x8bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2.710977] mmc0: SDHCI controller on 68cf1000.sdhci [68cf1000.sdhci] using ADMA [ 2.749889] mmc1: SDHCI controller on 68cf2000.sdhci [68cf2000.sdhci] using ADMA [ 2.757702] rtc-efi rtc-efi: setting system clock to 2020-02-25T20:25:30 UTC (1582662330) [ 2.766433] arm-smmu 64000000.mmu: Blocked unknown Stream ID 0x6004; boot with "arm-smmu.disable_bypass=0" to allow, but this may have security implications [ 2.780877] arm-smmu 64000000.mmu: GFSR 0x80000002, GFSYNR0 0x00000000, GFSYNR1 0x00006004, GFSYNR2 0x00000000 [ 2.784549] bgmac-enet 68c40000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 2.791279] bgmac-enet 68c40000.ethernet: Unknown IRQs: 0x00000800 [ 2.810430] IP-Config: Complete: [ 2.813761] device=eth0, hwaddr=00:10:18:9b:05:d3, ipaddr=10.136.13.29, mask=255.255.255.0, gw=10.136.13.1 [ 2.824175] host=10.136.13.29, domain=, nis-domain=(none) [ 2.830196] bootserver=10.136.4.151, rootserver=10.136.4.151, rootpath= [ 2.837533] ALSA device list: [ 2.839351] mmc0: new DDR MMC card at address 0001 [ 2.840599] No soundcards found. [ 2.845723] mmcblk0: mmc0:0001 MMC16G 14.6 GiB [ 2.853800] ttyS0 - failed to request DMA [ 2.853825] mmcblk0boot0: mmc0:0001 MMC16G partition 1 4.00 MiB [ 2.864142] mmcblk0boot1: mmc0:0001 MMC16G partition 2 4.00 MiB [ 2.870292] mmcblk0rpmb: mmc0:0001 MMC16G partition 3 128 KiB, chardev (236:0) [ 2.886855] mmcblk0: p1 p2 p3 p4 p5 [ 2.903229] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) [ 2.911601] VFS: Mounted root (ext4 filesystem) on device 179:4. [ 2.919448] devtmpfs: mounted [ 2.923573] Freeing unused kernel memory: 5184K [ 2.928354] Run /sbin/init as init process [ 3.018346] random: fast init done [ 3.145798] nf_defrag_ipv6: version magic '5.5.0 SMP mod_unload modversions aarch64' should be '5.5.0 SMP preempt mod_unload aarch64' [ 3.183202] systemd[1]: systemd 244.3+ running in system mode. (-PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 3.205677] systemd[1]: Detected architecture arm64.
