From: Joerg Roedel <jroedel@xxxxxxx> Switch back to the trampoline stack before returning to userspace. Signed-off-by: Joerg Roedel <jroedel@xxxxxxx> --- arch/x86/entry/entry_32.S | 79 +++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 77 insertions(+), 2 deletions(-) diff --git a/arch/x86/entry/entry_32.S b/arch/x86/entry/entry_32.S index 528db7d..357b82b 100644 --- a/arch/x86/entry/entry_32.S +++ b/arch/x86/entry/entry_32.S @@ -347,6 +347,60 @@ .endm /* + * Switch back from the kernel stack to the entry stack. + * + * The %esp register must point to pt_regs on the task stack. It will + * first calculate the size of the stack-frame to copy, depending on + * whether we return to VM86 mode or not. With that it uses 'rep movsl' + * to copy the contents of the stack over to the entry stack. + * + * We must be very careful here, as we can't trust the contents of the + * task-stack once we switched to the entry-stack. When an NMI happens + * while on the entry-stack, the NMI handler will switch back to the top + * of the task stack, overwriting our stack-frame we are about to copy. + * Therefore we switch the stack only after everything is copied over. + */ +.macro SWITCH_TO_ENTRY_STACK + + ALTERNATIVE "", "jmp .Lend_\@", X86_FEATURE_XENPV + + /* Bytes to copy */ + movl $PTREGS_SIZE, %ecx + +#ifdef CONFIG_VM86 + testl $(X86_EFLAGS_VM), PT_EFLAGS(%esp) + jz .Lcopy_pt_regs_\@ + + /* Additional 4 registers to copy when returning to VM86 mode */ + addl $(4 * 4), %ecx + +.Lcopy_pt_regs_\@: +#endif + + /* Initialize source and destination for movsl */ + movl PER_CPU_VAR(cpu_tss_rw + TSS_sp0), %edi + subl %ecx, %edi + movl %esp, %esi + + /* Save future stack pointer in %ebx */ + movl %edi, %ebx + + /* Copy over the stack-frame */ + shrl $2, %ecx + cld + rep movsl + + /* + * Switch to entry-stack - needs to happen after everything is + * copied because the NMI handler will overwrite the task-stack + * when on entry-stack + */ + movl %ebx, %esp + +.Lend_\@: +.endm + +/* * %eax: prev task * %edx: next task */ @@ -586,25 +640,45 @@ ENTRY(entry_SYSENTER_32) /* Opportunistic SYSEXIT */ TRACE_IRQS_ON /* User mode traces as IRQs on. */ + + /* + * Setup entry stack - we keep the pointer in %eax and do the + * switch after almost all user-state is restored. + */ + + /* Load entry stack pointer and allocate frame for eflags/eax */ + movl PER_CPU_VAR(cpu_tss_rw + TSS_sp0), %eax + subl $(2*4), %eax + + /* Copy eflags and eax to entry stack */ + movl PT_EFLAGS(%esp), %edi + movl PT_EAX(%esp), %esi + movl %edi, (%eax) + movl %esi, 4(%eax) + + /* Restore user registers and segments */ movl PT_EIP(%esp), %edx /* pt_regs->ip */ movl PT_OLDESP(%esp), %ecx /* pt_regs->sp */ 1: mov PT_FS(%esp), %fs PTGS_TO_GS + popl %ebx /* pt_regs->bx */ addl $2*4, %esp /* skip pt_regs->cx and pt_regs->dx */ popl %esi /* pt_regs->si */ popl %edi /* pt_regs->di */ popl %ebp /* pt_regs->bp */ - popl %eax /* pt_regs->ax */ + + /* Switch to entry stack */ + movl %eax, %esp /* * Restore all flags except IF. (We restore IF separately because * STI gives a one-instruction window in which we won't be interrupted, * whereas POPF does not.) */ - addl $PT_EFLAGS-PT_DS, %esp /* point esp at pt_regs->flags */ btrl $X86_EFLAGS_IF_BIT, (%esp) popfl + popl %eax /* * Return back to the vDSO, which will pop ecx and edx. @@ -673,6 +747,7 @@ ENTRY(entry_INT80_32) restore_all: TRACE_IRQS_IRET + SWITCH_TO_ENTRY_STACK .Lrestore_all_notrace: CHECK_AND_APPLY_ESPFIX .Lrestore_nocheck: -- 2.7.4
