On Mon, 2010-12-13 at 08:49 -0800, Sarah Sharp wrote:
> On Sun, Dec 12, 2010 at 12:26:48PM +0100, Peter Steiner wrote:
> > Hi
> >
> > compiled latest 2.6.36.2 but it reliably panics() my machine.
> > It happens if I try to dd sda to sdb (backup) using xhci USB3.0
> > (conceptronic CUSB3EXC) but ALSO using native USB 2.0 ports on the
> > machine - after 10-15 minutes of dd.
>
> Can you run lspci -v and lsusb? I'm wondering if the USB 2.0 ports are
> part of an EHCI host controller or an xHCI host controller.
USB 2.0 is built in controller, so they are EHCI.
The usb 3.0 ports are on a conceptronic CUSB3EXC ExpressCard expansion
card as I already mentioned. I've the card not at hand now, so here
lspci & lsusb WITHOUT the USB 3.0 card:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML
and 945GT Express Memory Controller Hub (rev 03)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=09 <?>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS,
943/940GML Express Integrated Graphics Controller (rev 03) (prog-if 00
[VGA controller])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at e8400000 (32-bit, non-prefetchable) [size=512K]
I/O ports at 6000 [size=8]
Memory at d0000000 (32-bit, prefetchable) [size=256M]
Memory at e8480000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [d0] Power Management version 2
Kernel driver in use: i915
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME,
943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0
Memory at e8500000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition
Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0, IRQ 41
Memory at e8580000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI
00
Capabilities: [100] Virtual Channel
Capabilities: [130] Root Complex Link
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port
1 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge:
00000000cf800000-00000000cf9fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device
30aa
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link
00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port
3 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=18, subordinate=18, sec-latency=0
I/O behind bridge: 00004000-00005fff
Memory behind bridge: e4000000-e7ffffff
Prefetchable memory behind bridge:
00000000cfa00000-00000000cfbfffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device
30aa
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port
4 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: e0000000-e3ffffff
Prefetchable memory behind bridge:
00000000cfc00000-00000000cfdfffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device
30aa
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 20
I/O ports at 6020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 21
I/O ports at 6040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at 6060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 6080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 20
Memory at e8584000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
(prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 00008000-00008fff
Memory behind bridge: e8100000-e83fffff
Prefetchable memory behind bridge:
00000000ec000000-00000000efffffff
Capabilities: [50] Subsystem: Hewlett-Packard Company Device
30aa
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 01)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE
Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at 60a0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family)
SATA AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 40
I/O ports at 13f0 [size=8]
I/O ports at 15f4 [size=4]
I/O ports at 1370 [size=8]
I/O ports at 1574 [size=4]
I/O ports at 60d0 [size=16]
Memory at e8585000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [70] Power Management version 2
Kernel driver in use: ahci
02:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: ec000000-effff000 (prefetchable)
Memory window 1: f0000000-f3fff000
I/O window 0: 00008000-000080ff
I/O window 1: 00008400-000084ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia
Card Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at e8108000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Kernel driver in use: tifm_7xx1
02:06.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard
Compliant SD Host Controller
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 64, IRQ 22
Memory at e8109000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Kernel driver in use: sdhci-pci
02:06.4 Communication controller: Texas Instruments PCIxx12 GemCore
based SmartCard controller
Subsystem: Hewlett-Packard Company nc6310
Flags: medium devsel, IRQ 10
Memory at e810a000 (32-bit, non-prefetchable) [size=4K]
Memory at e810b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
02:0e.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788
Gigabit Ethernet (rev 03)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at e8110000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
Kernel driver in use: tg3
08:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
[Golan] Network Connection (rev 02)
Subsystem: Hewlett-Packard Company Compaq 6710b or nx9420
Notebook
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at e8000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [e0] Express Legacy Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 00-1b-77-ff-ff-70-85-a0
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36.2 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1d.7
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 8
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0503 highspeed power enable connect
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 002: ID 0424:2503 Standard Microsystems Corp. USB 2.0 Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 2 TT per port
bMaxPacketSize0 64
idVendor 0x0424 Standard Microsystems Corp.
idProduct 0x2503 USB 2.0 Hub
bcdDevice 0.01
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 1 Single TT
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 2 TT per port
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 1 milli Ampere
DeviceRemovable 0x0e
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Port 3: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187
Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0bda Realtek Semiconductor Corp.
idProduct 0x8187 RTL8187 Wireless Adapter
bcdDevice 1.00
iManufacturer 1 Manufacturer_Realtek_RTL8187_
iProduct 2 RTL8187_Wireless_LAN_Adapter
iSerial 3 00C0CA1B8330
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 Wireless Network Card
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 0 (Defined at Interface level)
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 5 Bulk-IN,Bulk-OUT,Bulk-OUT
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 004: ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint
Sensor
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 8
idVendor 0x08ff AuthenTec, Inc.
idProduct 0x2580 AES2501 Fingerprint Sensor
bcdDevice 6.23
iManufacturer 0
iProduct 1 Fingerprint Sensor
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36.2 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36.2 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36.2 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36.2 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
>
> > Please see attached screenshot (I cannot copy it as text as it takes
> > down the machine and locks up in text console, so I can only make a
> > foto).
>
> Can you run netconsole to capture more of the messages before that? If
> you need help with setting up netconsole, see:
> http://sarah.thesharps.us/2010-03-26-09-41
>
I'm afraid I lack the time to play with kernel setup... :(
> > see attached .config.
> >
> > The bug did NOT happen on 2.6.35.7 - however there the USB3.0 xhci
> > frequently disconnects the sdb backup disk and dd fails after 400GB of
> > copy or so (but no panic).
>
> Would this happen to be on a Lenovo W510 laptop? I've received reports
> of different oopses caused by disconnects, while running 2.6.35.8:
>
> http://marc.info/?l=linux-kernel&m=129131271416325&w=2
>
> Do you see panics or oopses when you run 2.6.35.8? Or did you just
> upgrade straight from 2.6.35.7 to 2.6.36.2?
upgraded from 2.6.35.7 to 2.6.36 => panics
so then upgraded from 2.6.36 to 2.6.36.2 => same panic() while dd
As I said this happens equally if I connect my backup station to either
native USB 2.0 (USB3.0 NOT plugged in!) or the conceptronics USB 3.0.
The backup station is Sharkoon SATA Quickport 3.0.
Hope this helps.
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxxx For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom policy in Canada: sign http://dissolvethecrtc.ca/
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>