Re: [PATCH v6 4/4] sparc64: Add support for ADI (Application Data Integrity)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> On Mar 6, 2017, at 4:31 PM, Khalid Aziz <khalid.aziz@xxxxxxxxxx> wrote:
> 
> On 03/06/2017 05:13 PM, Anthony Yznaga wrote:
>> 
>>> On Feb 28, 2017, at 10:35 AM, Khalid Aziz <khalid.aziz@xxxxxxxxxx> wrote:
>>> 
>>> diff --git a/arch/sparc/kernel/etrap_64.S b/arch/sparc/kernel/etrap_64.S
>>> index 1276ca2..7be33bf 100644
>>> --- a/arch/sparc/kernel/etrap_64.S
>>> +++ b/arch/sparc/kernel/etrap_64.S
>>> @@ -132,7 +132,33 @@ etrap_save:	save	%g2, -STACK_BIAS, %sp
>>> 		stx	%g6, [%sp + PTREGS_OFF + PT_V9_G6]
>>> 		stx	%g7, [%sp + PTREGS_OFF + PT_V9_G7]
>>> 		or	%l7, %l0, %l7
>>> -		sethi	%hi(TSTATE_TSO | TSTATE_PEF), %l0
>>> +661:		sethi	%hi(TSTATE_TSO | TSTATE_PEF), %l0
>>> +		/*
>>> +		 * If userspace is using ADI, it could potentially pass
>>> +		 * a pointer with version tag embedded in it. To maintain
>>> +		 * the ADI security, we must enable PSTATE.mcde. Userspace
>>> +		 * would have already set TTE.mcd in an earlier call to
>>> +		 * kernel and set the version tag for the address being
>>> +		 * dereferenced. Setting PSTATE.mcde would ensure any
>>> +		 * access to userspace data through a system call honors
>>> +		 * ADI and does not allow a rogue app to bypass ADI by
>>> +		 * using system calls. Setting PSTATE.mcde only affects
>>> +		 * accesses to virtual addresses that have TTE.mcd set.
>>> +		 * Set PMCDPER to ensure any exceptions caused by ADI
>>> +		 * version tag mismatch are exposed before system call
>>> +		 * returns to userspace. Setting PMCDPER affects only
>>> +		 * writes to virtual addresses that have TTE.mcd set and
>>> +		 * have a version tag set as well.
>>> +		 */
>>> +		.section .sun_m7_1insn_patch, "ax"
>>> +		.word	661b
>>> +		sethi	%hi(TSTATE_TSO | TSTATE_PEF | TSTATE_MCDE), %l0
>>> +		.previous
>>> +661:		nop
>>> +		.section .sun_m7_1insn_patch, "ax"
>>> +		.word	661b
>>> +		.word 0xaf902001	/* wrpr %g0, 1, %pmcdper */
>> 
>> Since PMCDPER is never cleared, setting it here is quickly going to set it on all CPUs and then become an expensive "nop" that burns ~50 cycles each time through etrap.  Consider setting it at boot time and when a CPU is DR'd into the system.
>> 
>> Anthony
>> 
> 
> I considered that possibility. What made me uncomfortable with that is there is no way to prevent a driver/module or future code elsewhere in kernel from clearing PMCDPER with possibly good reason. If that were to happen, setting PMCDPER here ensures kernel will always see consistent behavior with system calls. It does come at a cost. Is that cost unacceptable to ensure consistent behavior?

Aren't you still at risk if the thread relinquishes the CPU while in the kernel and is then rescheduled on a CPU where PMCDPER has erroneously been left cleared?  You may need to save and restore PMCDPER as well as MCDPER on context switch, but I don't know if that will cover you completely.

Alternatively you can avoid problems from buggy code and avoid the performance hit when storing to ADI enabled memory with precise mode enabled (e.g. when reading from a file into an ADI-enabled buffer) by handling disrupting mismatches that happen in copy_to_user() or put_user().  That does require adding error barriers and appropriate exception table entries, though, to deal with the nature of disrupting exceptions.

Anthony

> 
> --
> Khalid

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxx.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [eCos]     [Asterisk Internet PBX]     [Linux API]
  Powered by Linux