Re: [RFC, PATCHv2 29/29] mm, x86: introduce RLIMIT_VADDR

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jan 11, 2017 at 10:09:17AM -0800, Andy Lutomirski wrote:
> On Wed, Jan 11, 2017 at 6:29 AM, Kirill A. Shutemov
> <kirill@xxxxxxxxxxxxx> wrote:
> > On Thu, Jan 05, 2017 at 12:49:44PM -0800, Dave Hansen wrote:
> >> On 01/05/2017 12:14 PM, Andy Lutomirski wrote:
> >> >> I'm not sure I'm comfortable with this.  Do other rlimit changes cause
> >> >> silent data corruption?  I'm pretty sure doing this to MPX would.
> >> >>
> >> > What actually goes wrong in this case?  That is, what combination of
> >> > MPX setup of subsequent allocations will cause a problem, and is the
> >> > problem worse than just a segfault?  IMO it would be really nice to
> >> > keep the messy case confined to MPX.
> >>
> >> The MPX bounds tables are indexed by virtual address.  They need to grow
> >> if the virtual address space grows.   There's an MSR that controls
> >> whether we use the 48-bit or 57-bit layout.  It basically decides
> >> whether we need a 2GB (48-bit) or 1TB (57-bit) bounds directory.
> >>
> >> The question is what we do with legacy MPX applications.  We obviously
> >> can't let them just allocate a 2GB table and then go let the hardware
> >> pretend it's 1TB in size.  We also can't hand the hardware using a 2GB
> >> table an address >48-bits.
> >>
> >> Ideally, I'd like to make sure that legacy MPX can't be enabled if this
> >> RLIMIT is set over 48-bits (really 47).  I'd also like to make sure that
> >> legacy MPX is active, that the RLIMIT can't be raised because all hell
> >> will break loose when the new addresses show up.
> >
> > I think we can do this. See the patch below.
> >
> > Basically, we refuse to enable MPX and issue warning in dmesg if there's
> > anything mapped above 47-bits. Once MPX is enabled, mmap_max_addr() cannot
> > be higher than 47-bits too.
> >
> > Function call from mmap_max_addr() is unfortunate, but I don't see a
> > way around.
> 
> How about preventing the max addr from being changed to too high a
> value while MPX is on instead of overriding the set value?  This would
> have the added benefit that it would prevent silent failures where you
> think you've enabled large addresses but MPX is also on and mmap
> refuses to return large addresses.

Setting rlimit high doesn't mean that you necessary will get access to
full address space, even without MPX in picture. TASK_SIZE limits the
available address space too.

I think it's consistent with other resources in rlimit: setting RLIMIT_RSS
to unlimited doesn't really means you are not subject to other resource
management.

-- 
 Kirill A. Shutemov

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxx.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [eCos]     [Asterisk Internet PBX]     [Linux API]