* Kirill A. Shutemov (kirill@xxxxxxxxxxxxx) wrote:
> On Fri, Apr 15, 2016 at 02:42:33PM +0100, Dr. David Alan Gilbert wrote:
> > * Kirill A. Shutemov (kirill@xxxxxxxxxxxxx) wrote:
> > > On Thu, Apr 14, 2016 at 12:22:30PM -0400, Andrea Arcangeli wrote:
> > > > Adding linux-mm too,
> > > >
> > > > On Thu, Apr 14, 2016 at 01:34:41PM +0100, Dr. David Alan Gilbert wrote:
> > > > > * Andrea Arcangeli (aarcange@xxxxxxxxxx) wrote:
> > > > >
> > > > > > The next suspect is the massive THP refcounting change that went
> > > > > > upstream recently:
> > > > >
> > > > > > As further debug hint, can you try to disable THP and see if that
> > > > > > makes the problem go away?
> > > > >
> > > > > Yep, this seems to be the problem (cc'ing in Kirill).
> > > > >
> > > > > 122afea9626ab3f717b250a8dd3d5ebf57cdb56c - works (just before Kirill disables THP)
> > > > > 61f5d698cc97600e813ca5cf8e449b1ea1c11492 - breaks (when THP is reenabled)
> > > > >
> > > > > It's pretty reliable; as you say disabling THP makes it work again
> > > > > and putting it back to THP/madvise mode makes it break. And you need
> > > > > to test on a machine with some free ram to make sure THP has a chance
> > > > > to have happened.
> > > > >
> > > > > I'm not sure of all of the rework that happened in that series,
> > > > > but my reading of it is that splitting of THP pages gets deferred;
> > > > > so I wonder if when I do the madvise to turn THP off, if it's actually
> > > > > still got THP pages and thus we end up with a whole THP mapped
> > > > > when I'm expecting to be userfaulting those pages.
> > > >
> > > > Good thing at least I didn't make UFFDIO_COPY THP aware yet so there's
> > > > less variables (as no user was interested to handle userfaults at THP
> > > > granularity yet, and from userland such an improvement would be
> > > > completely invisible in terms of API, so if an user starts doing that
> > > > we can just optimize the kernel for it, criu restore could do that as
> > > > the faults will come from disk-I/O, when network is involved THP
> > > > userfaults wouldn't have a great tradeoff with regard to the increased
> > > > fault latency).
> > > >
> > > > I suspect there is an handle_userfault missing somewhere in connection
> > > > with trans_huge_pmd splits (not anymore THP splits) that you're doing
> > > > with MADV_DONTNEED to zap those pages in the destination that got
> > > > redirtied in source during the last precopy stage. Or more simply
> > > > MADV_DONTNEED isn't zapping all the right ptes after the trans huge
> > > > pmd got splitted.
> > > >
> > > > The fact the page isn't splitted shouldn't matter too much, all we care
> > > > about is the pte triggers handle_userfault after MADV_DONTNEED.
> > > >
> > > > The userfaultfd testcase in the kernel isn't exercising this case
> > > > unfortunately, that should probably be improved too, so there is a
> > > > simpler way to reproduce than running precopy before postcopy in qemu.
> > >
> > > I've tested current Linus' tree and v4.5 using qemu postcopy test case for
> > > both x86-64 and i386 and it never failed for me:
> > >
> > > /x86_64/postcopy: first_byte = 7e last_byte = 7d hit_edge = 1 OK
> > > OK
> > > /i386/postcopy: first_byte = f6 last_byte = f5 hit_edge = 1 OK
> > > OK
> > >
> > > I've run it directly, setting relevant QTEST_QEMU_BINARY.
> >
> > Interesting; it's failing reliably for me - but only with a reasonably
> > freshly booted machine (so that the pages get THPd).
>
> The same here. Freshly booted machine with 64GiB ram. I've checked
> /proc/vmstat: huge pages were allocated
Thanks for testing.
Damn; this is confusing now. I've got a RHEL7 box with 4.6.0-rc3 on where it
works, and a fedora24 VM where it fails (the f24 VM is where I did the bisect
so it works fine with the older kernel on the f24 userspace in that VM).
So lets see:
works: Kirill's (64GB machine)
Dave's RHEL7 host (24GB RAM, dual xeon, RHEL7 userspace and kernel config)
fails: Dave's f24 VM (4GB RAM, 4 vcpus VM on my laptop24 userspace and kernel config)
So it's any of userspace, kernel config, machine hardware or hmm.
My f24 box has transparent_hugepage_madvise, where my rhel7 has transparent_hugepage_always
(but still works if I flip it to madvise at run time). I'll try and get the configs
closer together.
Liang Li: Can you run my test on your setup which fails the migrate and tell
me what your userspace is?
(If you've not built my test yet, you might find you need to add a :
tests/postcopy-test$(EXESUF): tests/postcopy-test.o
to the tests/Makefile)
Dave
>
> --
> Kirill A. Shutemov
--
Dr. David Alan Gilbert / dgilbert@xxxxxxxxxx / Manchester, UK
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxx. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>