On Mon, Jul 26, 2010 at 03:28:32PM +0800, Wu Fengguang wrote:
> On Mon, Jul 19, 2010 at 09:11:30PM +0800, Mel Gorman wrote:
> > There are a number of cases where pages get cleaned but two of concern
> > to this patch are;
> > o When dirtying pages, processes may be throttled to clean pages if
> > dirty_ratio is not met.
> > o Pages belonging to inodes dirtied longer than
> > dirty_writeback_centisecs get cleaned.
> >
> > The problem for reclaim is that dirty pages can reach the end of the LRU
> > if pages are being dirtied slowly so that neither the throttling cleans
> > them or a flusher thread waking periodically.
> >
> > Background flush is already cleaning old or expired inodes first but the
> > expire time is too far in the future at the time of page reclaim. To mitigate
> > future problems, this patch wakes flusher threads to clean 1.5 times the
> > number of dirty pages encountered by reclaimers. The reasoning is that pages
> > were being dirtied at a roughly constant rate recently so if N dirty pages
> > were encountered in this scan block, we are likely to see roughly N dirty
> > pages again soon so try keep the flusher threads ahead of reclaim.
> >
> > This is unfortunately very hand-wavy but there is not really a good way of
> > quantifying how bad it is when reclaim encounters dirty pages other than
> > "down with that sort of thing". Similarly, there is not an obvious way of
> > figuring how what percentage of dirty pages are old in terms of LRU-age and
> > should be cleaned. Ideally, the background flushers would only be cleaning
> > pages belonging to the zone being scanned but it's not clear if this would
> > be of benefit (less IO) or not (potentially less efficient IO if an inode
> > is scattered across multiple zones).
> >
> > Signed-off-by: Mel Gorman <mel@xxxxxxxxx>
> > ---
> > mm/vmscan.c | 18 +++++++++++-------
> > 1 files changed, 11 insertions(+), 7 deletions(-)
> >
> > diff --git a/mm/vmscan.c b/mm/vmscan.c
> > index bc50937..5763719 100644
> > --- a/mm/vmscan.c
> > +++ b/mm/vmscan.c
> > @@ -806,6 +806,8 @@ restart_dirty:
> > }
> >
> > if (PageDirty(page)) {
> > + nr_dirty++;
> > +
> > /*
> > * If the caller cannot writeback pages, dirty pages
> > * are put on a separate list for cleaning by either
> > @@ -814,7 +816,6 @@ restart_dirty:
> > if (!reclaim_can_writeback(sc, page)) {
> > list_add(&page->lru, &dirty_pages);
> > unlock_page(page);
> > - nr_dirty++;
> > goto keep_dirty;
> > }
> >
> > @@ -933,13 +934,16 @@ keep_dirty:
> > VM_BUG_ON(PageLRU(page) || PageUnevictable(page));
> > }
> >
> > + /*
> > + * If reclaim is encountering dirty pages, it may be because
> > + * dirty pages are reaching the end of the LRU even though
> > + * the dirty_ratio may be satisified. In this case, wake
> > + * flusher threads to pro-actively clean some pages
> > + */
> > + wakeup_flusher_threads(laptop_mode ? 0 : nr_dirty + nr_dirty / 2);
>
> Ah it's very possible that nr_dirty==0 here! Then you are hitting the
> number of dirty pages down to 0 whether or not pageout() is called.
>
True, this has been fixed to only wakeup flusher threads when this is
the file LRU, dirty pages have been encountered and the caller has
sc->may_writepage.
> Another minor issue is, the passed (nr_dirty + nr_dirty / 2) is
> normally a small number, much smaller than MAX_WRITEBACK_PAGES.
> The flusher will sync at least MAX_WRITEBACK_PAGES pages, this is good
> for efficiency.
> And it seems good to let the flusher write much more
> than nr_dirty pages to safeguard a reasonable large
> vmscan-head-to-first-dirty-LRU-page margin. So it would be enough to
> update the comments.
>
Ok, the reasoning had been to flush a number of pages that was related
to the scanning rate but if that is inefficient for the flusher, I'll
use MAX_WRITEBACK_PAGES.
Thanks
--
Mel Gorman
Part-time Phd Student Linux Technology Center
University of Limerick IBM Dublin Software Lab
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@xxxxxxxxxx For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@xxxxxxxxx";> email@xxxxxxxxx </a>