On Wed, Nov 06, 2024 at 11:11:23PM -0700, Abhinav Saxena wrote: > Fix unintentional word repetitions in devicetree binding documentation: > - usb.txt: Fix repeated "two" > - mvebu-devbus.txt: Fix repeated "from" > - gpio.txt: Fix repeated "Both" > - pinctrl-bindings.txt: Fix repeated "device" > - cavium/bootbus.txt: Fix repeated "one" > > These issues were identified using the checkpatch.pl script. > > Signed-off-by: Abhinav Saxena <xandfury@xxxxxxxxx> > --- > Documentation/devicetree/bindings/gpio/gpio.txt | 2 +- This and... > .../devicetree/bindings/memory-controllers/mvebu-devbus.txt | 2 +- > Documentation/devicetree/bindings/mips/cavium/bootbus.txt | 2 +- > Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | 2 +- ...this I'll take. The others need to be converted to schema. > Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/usb.txt | 2 +- > 5 files changed, 5 insertions(+), 5 deletions(-) > > diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt > index d82c32217fff..530420475a4f 100644 > --- a/Documentation/devicetree/bindings/gpio/gpio.txt > +++ b/Documentation/devicetree/bindings/gpio/gpio.txt > @@ -304,7 +304,7 @@ pins 50..69. > It is also possible to use pin groups for gpio ranges when pin groups are the > easiest and most convenient mapping. > > -Both both <pinctrl-base> and <count> must set to 0 when using named pin groups > +Both <pinctrl-base> and <count> must set to 0 when using named pin groups > names. > > The property gpio-ranges-group-names must contain exactly one string for each > diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt > index 8b9388cc1ccc..1983d7eabd2b 100644 > --- a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt > +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt > @@ -43,7 +43,7 @@ Read parameters: > - devbus,bus-width: Defines the bus width, in bits (e.g. <16>). > Mandatory, except if devbus,keep-config is used. > > - - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle, > + - devbus,badr-skew-ps: Defines the time delay from A[2:0] toggle, > to read data sample. This parameter is useful for > synchronous pipelined devices, where the address > precedes the read data by one or two cycles. > diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt > index 6581478225a2..1bc655d285ce 100644 > --- a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt > +++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt > @@ -15,7 +15,7 @@ Properties: > > - #size-cells: Must be <1>. > > -- ranges: There must be one one triplet of (child-bus-address, > +- ranges: There must be one triplet of (child-bus-address, > parent-bus-address, length) for each active chip select. If the > length element for any triplet is zero, the chip select is disabled, > making it inactive. > diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt > index 6904072d3944..500b76ba2ab3 100644 > --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt > @@ -18,7 +18,7 @@ states. The number and names of those states is defined by the client device's > own binding. > > The common pinctrl bindings defined in this file provide an infrastructure > -for client device device tree nodes to map those state names to the pin > +for client device tree nodes to map those state names to the pin Actually I think this was correct. See "client device" used above. Maybe "client device Devicetree nodes" would be a bit clearer and use the right form of Devicetree. Rob
